journal article·2020-02Open access

Understanding Particle–Particle Interactions from Deposition Efficiencies in Cold Spray of Mixed Fe/316L Powders with Different Particle Size Combinations

Xin Chu, Hanqing Che, Chaoyi Teng, Phuong Vo, Stephen Yue

Abstract

In this study, Fe and 316L powders with two different particle sizes were used as the feedstock. They were also premixed using different mixing ratios and combinations: (i) either 316L or Fe powder with large particles blended with small ones and (ii) a blend of 316L and Fe powder using three particle size combinations. Both single-component and mixed powders were deposited by cold spray, and the deposition efficiencies (DEs) were calculated and discussed. The results show that the DE of a mixture of large and small particles of the same powder follows the Rule of Mixtures, whereas the variation of the DE of the 316L and Fe mixture depends on the particle size combinations; specifically, mixtures with smaller-sized particles show better DEs than the respective Fe powder. The difference in the DEs of different Fe/316L mixtures can be explained by the particle–particle interactions (i.e., tamping and retention) upon impact. In addition, a relationship between the average particle size and density is proposed to determine the occurrence of particle–particle interactions in cold spray of mixed generic powders. The industrial significance of the knowledge of particle–particle interactions is finally explained in the context of the fabrications of metal matrix composites.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Particle Dynamics in Fluid Flows · Flame retardant materials and properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. A. Moridi, S.M. Hassani-Gangaraj, M. Guagliano, and M. Dao, Cold Spray Coating: Review of Material Systems and Future Perspectives, Surf. Eng., 2014, 30(6), p 369-39510.1179/1743294414Y.0000000270 ↗
2. T. Novoselova, P. Fox, R. Morgan, and W. O’Neill, Experimental Study of Titanium/Aluminium Deposits Produced by Cold Gas Dynamic Spray, Surf. Coat. Technol., 2006, 200(8), p 2775-278310.1016/j.surfcoat.2004.10.133 ↗
3. H.Y. Lee, S.H. Jung, S.Y. Lee, and K.H. Ko, Alloying of Cold-Sprayed Al–Ni Composite Coatings by Post-Annealing, Appl. Surf. Sci., 2007, 253(7), p 3496-350210.1016/j.apsusc.2006.07.053 ↗
4. H.-T. Wang, C.-J. Li, G.-J. Yang, and C.-X. Li, Cold Spraying of Fe/Al Powder Mixture: Coating Characteristics and Influence of Heat Treatment on the Phase Structure, Appl. Surf. Sci., 2008, 255(5), p 2538-254410.1016/j.apsusc.2008.07.127 ↗
5. W. Wong, P. Vo, E. Irissou, A.N. Ryabinin, J.G. Legoux, and S. Yue, Effect of Particle Morphology and Size Distribution on Cold-Sprayed Pure Titanium Coatings, J. Therm. Spray Technol., 2013, 22(7), p 1140-115310.1007/s11666-013-9951-6 ↗
6. H. Aydin, M. Alomair, W. Wong, P. Vo, and S. Yue, Cold Sprayability of Mixed Commercial Purity Ti plus Ti6Al4V Metal Powders, J. Therm. Spray Technol., 2017, 26(3), p 360-37010.1007/s11666-017-0528-7 ↗
7. T. Piwowarczyk, M. Winnicki, A. Małachowska, and A. Ambroziak, Casting Defects Filling by Low Pressure Cold Spraying Method, Arch. Foundry Eng., 2014, 14(1), p 109-114
8. H. Che, X. Chu, P. Vo, and S. Yue, Cold Spray of Mixed Metal Powders on Carbon Fibre Reinforced Polymers, Surf. Coat. Technol., 2017, 329, p 232-24310.1016/j.surfcoat.2017.09.052 ↗
9. S. Yue, W. Wong, H. Aydin, R. Mongrain, R. Barua, P. Vo, R. Dolbec, Improving Cold Sprayability: Mixed Metal Powders, Thermal Spray 2015: Proceedings of the International Thermal Spray Conference, A. McDonald, A. Agarwal, G. Bolelli, A. Concustell, Y.-C. Lau, F.-L. Toma, E. Turunen, and C. Widener, Ed., May 11-14, 2015 (Long Beach, California), Springer, 2016, 473 p10.31399/asm.cp.itsc2015p0473 ↗
10. R.G. Maev and V. Leshchynsky, Air Gas Dynamic Spraying of Powder Mixtures: Theory and Application, J. Therm. Spray Technol., 2016, 15(2), p 198-20510.1361/105996306X108048 ↗
11. E. Irissou, J.-G. Legoux, B. Arsenault, and C. Moreau, Investigation of Al-Al2O3 Cold Spray Coating Formation and Properties, J. Therm. Spray Technol., 2007, 5(16), p 661-66810.1007/s11666-007-9086-8 ↗
12. R. Fernandez and B. Jodoin, Cold Spray Aluminum-Alumina Cermet Coatings: Effect of Alumina Content, J. Therm. Spray Technol., 2018, 27(4), p 603-62310.1007/s11666-018-0702-6 ↗
13. K. Ito and Y. Ichikawa, Microstructure Control of Cold-Sprayed Pure Iron Coatings Formed Using Mechanically Milled Powder, Surf. Coat. Technol., 2019, 357, p 129-13910.1016/j.surfcoat.2018.10.016 ↗
14. J. Perry, P. Richer, B. Jodoin, and E. Matte, Pin Fin Array Heat Sinks by Cold Spray Additive Manufacturing: Economics of Powder Recycling, J. Therm. Spray Technol., 2018, 28(1–2), p 144-160
15. X.-T. Luo, Y.-K. Wei, Y. Wang, and C.-J. Li, Microstructure and Mechanical Property of Ti and Ti6Al4V Prepared by an In-Situ Shot Peening Assisted Cold Spraying, Mater. Des., 2015, 85, p 527-53310.1016/j.matdes.2015.07.015 ↗
16. P.C. King, S.H. Zahiri, and M.Z. Jahedi, Rare Earth/Metal Composite Formation by Cold Spray, J. Therm. Spray Technol., 2017, 17(2), p 221-22710.1007/s11666-007-9145-1 ↗
17. S. Ahmad Alidokht, P. Vo, S. Yue, and R.R. Chromik, Erosive Wear Behavior of Cold-Sprayed Ni-WC Composite Coating, Wear, 2017, 376, p 566-57710.1016/j.wear.2017.01.052 ↗
18. S.M. Hassani-Gangaraj, A. Moridi, and M. Guagliano, Critical Review of Corrosion Protection by Cold Spray Coatings, Surf. Eng., 2015, 31(11), p 803-81510.1179/1743294415Y.0000000018 ↗
19. R. Barua, Study of the Structural Properties and Control of Degradation Rate for Biodegradable Metallic Stents using Cold Spray, Ph.D. Thesis, McGill University, 2015
20. X. Chu, R. Chakrabarty, H. Che, L. Shang, P. Vo, J. Song, and S. Yue, Investigation of the Feedstock Deposition Behavior in a Cold Sprayed 316L/Fe Composite Coating, Surf. Coat. Technol., 2018, 337, p 53-6210.1016/j.surfcoat.2017.12.063 ↗
21. X. Chu, H. Che, P. Vo, R. Chakrabarty, B. Sun, J. Song, and S. Yue, Understanding the Cold Spray Deposition Efficiencies of 316L/Fe Mixed Powders by Performing Splat Tests onto As-Polished Coatings, Surf. Coat. Technol., 2017, 324, p 353-36010.1016/j.surfcoat.2017.05.083 ↗
22. W.Y. Li, C. Zhang, H.T. Wang, X.P. Guo, H.L. Liao, C.J. Li, and C. Coddet, Significant Influences of Metal Reactivity and Oxide Films at Particle Surfaces on Coating Microstructure in Cold Spraying, Appl. Surf. Sci., 2017, 253(7), p 3557-356210.1016/j.apsusc.2006.07.063 ↗
23. Y.-K. Wei, X.-T. Luo, C.-X. Li, and C.-J. Li, Optimization of In-Situ Shot-Peening-Assisted Cold Spraying Parameters for Full Corrosion Protection of Mg Alloy by Fully Dense Al-based Alloy Coating, J. Therm. Spray Technol., 2016, 26(1–2), p 173-183
24. X.-T. Luo, M.-L. Yao, N. Ma, M. Takahashi, and C.-J. Li, Deposition Behavior, Microstructure and Mechanical Properties of an In-Situ Micro-Forging Assisted Cold Spray Enabled Additively Manufactured Inconel 718 Alloy, Mater. Des., 2018, 155, p 384-39510.1016/j.matdes.2018.06.024 ↗