The Mechanical and Tribological Properties of Cold-Sprayed Cermet Coatings—Al Alloy Substrate Systems
Source abstract
Abstract
Abstract The article describes the influence of a solid lubricant such as graphite on the coating-substrate adhesion, susceptibility to cracking during three-point bending tests and tribological properties of the cermet coating-substrate systems. Two types of deposits Cr3C2-25(Ni20Cr) and (Cr3C2-25(Ni20Cr))-5(Ni25C), cold-sprayed on the Al 7075 alloy substrate, were analyzed. The Cr3C2-25(Ni20Cr) coatings showed a homogeneous microstructure with evenly distributed ceramic particles in a Ni20Cr matrix. The (Cr3C2-25(Ni20Cr))-5(Ni25C) deposits also contained graphite placed both between metallic particles and near the crushed ceramic Cr3C2 particles. The force required for the crack that appeared in the coating-substrate system during the three-point bending test under constant velocity was significantly higher in the case of (Cr3C2-25(Ni20Cr))-5(Ni25C) deposit than in that without the solid lubricant. The cracks were observed perpendicular to the coating-substrate interface. The graphite embedded in the cermet coating structure prevented the formation of crack nuclei during three-point bending test under cyclic load at room temperature and reduced the size of cracks in the deposit at 200 °C. Both cermet coatings revealed the same adhesion. The addition of graphite not only did not deteriorate the adhesion of the deposits and thus their quality but also improved their other properties, such as flexural strength and wear resistance. Coatings containing the solid lubricant showed a lower wear index than the Cr3C2-25(Ni20Cr) deposits examined at both room and elevated temperatures. This recommends their use in industry as deposit working in heavy wear conditions. The presented results of mechanical tests effectively fill the gap regarding the properties of the cold-sprayed cermet coatings.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Advanced materials and composites · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. D. Wolfe, T. Eden, J. Potter and A. Jaroh, Investigation and Characterization of Cr3C2-Based Wear-Resistant Coatings Applied by the Cold Spray Process, J. Therm. Spray Technol., 2006, 15, p 400-412.10.1361/105996306X124400 ↗
2. P. Poza and M.A. Garrido-Maneiro, Cold-Sprayed Coatings: Microstructure, Mechanical Properties, and Wear Behaviour, Prog. Mater Sci., 2022, 123, 100839.10.1016/j.pmatsci.2021.100839 ↗
3. H. Singh, T.S. Sidhu, J. Karthikeyan and S.B.S. Kalsi, Development and Characterization of Cr3C2-NiCr Coated Superalloy by Novel Cold Spray Process, Mater. Manuf. Process., 2015, 31(11), p 1476-1482.10.1080/10426914.2014.973599 ↗
4. R. Fernandez and B. Jodoin, Effect of Particle Morphology on cold Spray Deposition of Chromium Carbide-Nickel Chromium Cermet Powders, J. Therm. Spray Technol., 2017, 26, p 1356-1380.10.1007/s11666-017-0580-3 ↗
5. A. Trelka, W. Żórawski, Ł Maj, P. Petrzak, D. Soboń and A. Góral, The Effect of the Substrate on the Microstructure and Tribological Properties of Cold Sprayed (Cr3C2-25(Ni20Cr))-(Ni-graphite) Cermet Coatings, Materials., 2022, 15, p 994.10.3390/ma15030994 ↗
6. H. Assadi, H. Kreye, F. Gärtner and T. Klassen, Cold Spraying–A Materials Perspective, Acta Mater., 2016, 116, p 382-407.10.1016/j.actamat.2016.06.034 ↗
7. M. Winnicki, Advanced Functional Metal-Ceramic and Ceramic Coatings Deposited by Low-Pressure Cold Spraying: A Review, Coatings, 2021, 11(9), p 1044.10.3390/coatings11091044 ↗
8. W. Żórawski, A. Góral, M. Makrenek, D. Soboń, A. Trelka and M. Bara, Optimization of Mechanical Properties of Cr3C2-Ni20Cr/Graphite Cold Sprayed Coatings, Material, 2021, 14, p 3458.10.3390/ma14133458 ↗
9. A. Papyrin, A development of the cold spray process, The Cold Spray Materials Deposition Process Fundamentals and Applications. V.K. Champagne Ed., Woodhead Publishing Limited, England, Cambridge, 2007, p 11-4210.1533/9781845693787.1.11 ↗
10. A. Trelka, W. Żórawski and A. Góral, Microstructure and Properties Modification of Cold Sprayed Coatings Using Different Grain Size of Cr3C2-25(Ni20Cr) Composite Powder, Stroj. Vestn.-J. Mech. E., 2020, 66, p 494-504.10.5545/sv-jme.2020.6688 ↗
11. A. Góral, W. Żórawski and M. Makrenek, The Effect of the Standoff Distance on the Microstructure and Mechanical Properties of Cold Sprayed Cr3C2-25(Ni20Cr) Coatings, Surf. Coatings Technol., 2019, 361, p 9-18.10.1016/j.surfcoat.2019.01.006 ↗
12. M. Grujicic, Particle/substrate interaction in the cold-spray bonding process, The Cold Spray Materials Deposition Process. V.K. Champagne Ed., Fundamentals and applications. Woodhead Publishing Limited. England, Cambridge, 2007, p 148-17710.1533/9781845693787.2.148 ↗
13. L. Gyansah, N.H. Tariq, J.R. Tang, X. Qiu, B. Feng, J. Huang, H. Du, J.Q. Wang and T.Y. Xiong, Cold Spraying SiC /Al Metal Matrix Composites: Effects of SiC Contents and Heat Treatment on Microstructure, Thermophysical and Flexural Properties, Mater. Res. Express, 2018, 5, 026523.10.1088/2053-1591/aaaeee ↗
14. E. Mayrhofer, L. Janka, W.P. Mayr, J. Norpoth, M.R. Ripoll and M. Gröschl, Cracking resistance of Cr3C2–NiCr and WC–Cr3C2–Ni thermally sprayed coatings under tensile bending stress, Surf. Coat. Technol., 2015, 281, p 169-175.10.1016/j.surfcoat.2015.09.002 ↗
15. M. Gui, B. Eybel, B. Asselin and F. Monerie-Moulin, Cracking and spalling behavior of HVOF thermally sprayed WC-Co-Cr coating in bend and axial fatigue tests, J. Mater. Eng. Perform., 2015, 24(3), p 1347-1356.10.1007/s11665-014-1378-9 ↗
16. A. Koutsomichalis, K. Kalfountzos, P. Makri, M. Vardavoulias, N. Vaxevanidis, Tensile and bend behaviour of WC-Co-Cr HVOF coatings on steel, in 6th Panhellenic Conference on Metallic Materials, Ioannina, 7–9 December 2016, pp. 204-209.
17. M. Hahn and A. Fisher, Characterization of Thermal Spray Coatings for Cylinder Running Surfaces of Diesel Engines, J. Therm. Spray Technol., 2009, 19, p 866-872.10.1007/s11666-010-9488-x ↗
18. P. Bansal, N.P. Padture and A. Vasiliev, Improved Interfacial Mechanical Properties of Al2O313wt%TiO2 Plasma-Sprayed Coatings Derived from Nanocrystalline Powders, Acta Mater., 2003, 51, p 2959-2970.10.1016/S1359-6454(03)00109-5 ↗
19. A. Góral, W. Żórawski, L. Lityńska-Dobrzyńska, M. Makrenek, M. Goły, A. Trelka and M. Szlezynger, Laser Modification of the Microstructure and Mechanical Properties of (Cr3C2-25(Ni20Cr))-5(Ni25C) Cermet Coatings Containing a Solid Lubricant, Surf. Coat. Technol., 2020, 405, 126701.10.1016/j.surfcoat.2020.126701 ↗
20. D.X. Thao, H.V. Got, N.H. Phan and P.D. Cuong, Influence of Carbide Content on the Adhesion and Microscopic Hardness of Plasma Spray Cr3C2-NiCr Coating on 16Mn Steel, Chemical and Materials Engineering., 2019, 7(3), p 25–31.10.13189/cme.2019.070301 ↗
21. M. Winnicki, A. Machałowska, M. Rutkowska-Gorczyca, P. Sokołowska, A. Ambroziak and L. Pawłowski, Characterization of Cermet Coatings Deposited by Low-Pressure Cold Spraying, Surf. Coat. Technol., 2015, 268, p 108-114.10.1016/j.surfcoat.2014.12.070 ↗
22. W. Deng, X. Zhao, Y. An, J. Chen and H. Zhou, Study on Preparation and Tribological Properties of As-Sprayed 8YSZ/Graphite Coating, Surf. Eng., 2020, 36, p 1097-1106.10.1080/02670844.2019.1669348 ↗
23. B. Cai, Y.-F. Tan, Y.-G. Tu, X.-L. Wang and T. Xu, Effects of Graphite Content on Microstructure and Tribological Properties of Graphite/TiC/Ni-Base Alloy Composite Coatings, Trans. Nonferr. Met. Soc. China, 2011, 21(8), p 1741-1749.10.1016/S1003-6326(11)60924-2 ↗
24. J. Yi, M.L. Li, H.X. Zhou, A. Rosenkranz, B. Wang, H. Song and N. Jiang, Enhanced Tribological Properties of Y/MoS2 Composite Coatings Prepared by Chemical Vapor Deposition, Ceram. Int., 2020, 46(15), p 23813-23819.10.1016/j.ceramint.2020.06.157 ↗
25. W. Song, K. Sun, G. Zhao, L. Zhu, S. Wang and T. Li, Performance of MoS2/Zr Composite Coatings at Different Deposition Temperatures, Materials, 2021, 14(17), p 5100.10.3390/ma14175100 ↗
26. C.E. Morstein and M. Dienwiebel, Graphite Lubrication Mechanisms Under High Mechanical Load, Wear, 2021, 477, 203794.10.1016/j.wear.2021.203794 ↗
27. M. Alajmi, K.R. Alrashdan, T. Alsaeed and A. Shalwan, Tribological Characteristics of Graphite Epoxy Composites Using Adhesive Wear Experiments, J. Mater. Res. Technol, 2020, 9(6), p 13671-13681.10.1016/j.jmrt.2020.09.106 ↗
28. ISO 4624:2016; Paints and Varnishes—Pull‐Off Test for Adhesion. ISO: Geneva, Switzerland, 2016.
29. ISO 20808:2016(E); Fine Ceramics (Advanced Ceramics, Advanced Technical Ceramics)–Determination of Friction and Wear Characteristics of Monolithic Ceramics by Ball‐On‐Disc Method. ISO: Geneva, Switzerland, 2016.
30. F. Sevillano, P. Poza, C.J. Munez, S. Vezzu, S. Rech and A. Trentin, Cold-sprayed Ni-Al2O3 coatings for applications in power generation industry, J. Therm. Spray Technol, 2012, 22(5), p 772-782.10.1007/s11666-013-9890-2 ↗
31. S.V. Sajadifar, E. Scharifi, U. Weidig, K. Steinhoff and T. Niendorf, Performance of Thermo-Mechanically Processed AA7075 Alloy at Elevated Temperatures-From Microstructure to Mechanical Properties, Metals, 2020, 10(7), p 884.10.3390/met10070884 ↗
32. J. Soyama and C.T. Rios, Effect of Subcritical Annealing on the Microstructure and Mechanical Properties of a Precipitation-Hardened Al-Zn-Mg-Cu Alloy, J. Mater. Eng. Perform, 2021, 30(2), p 1012-1021.10.1007/s11665-020-05416-2 ↗
33. W. Hanyun, Y. Yinmiao, L. Haoqi, Y. Jie and K. Dejun, Tribological behavior of laser thermal sprayed Cr3C2–NiCr + 10%Ni/MoS2 composite coating on H13 hot work mould steel, Mater. Res. Express, 2019, 7, 016599.10.1088/2053-1591/ab5ec6 ↗