journal article·2019-08

Effect of HVOF Process Parameters on TiO2 Coatings: An Approach Using DoE and First-Order Process Maps

G. A. Clavijo-Mejía, D. G. Espinosa-Arbeláez, J. A. Hermann-Muñoz, A. L. Giraldo-Betancur, J. Muñoz-Saldaña

Publisher page

Abstract

High-velocity oxy-fuel deposition stages of titanium oxide coatings were analyzed and reported here. For the first stages of deposition, process maps were used to evaluate the influence of deposition parameters such as stand-off distance (SOD), powder feed rate (PFR) and fuel/oxygen ratio (F/O) on velocity and temperature of in-flight particles. These parameters were then combined with particle size distribution (PSD) to further optimize the deposition process considering the spray trace width and the area covered by splats and non-molten particles as responses. Furthermore, the structural, morphological and mechanical characteristics either of single splats, clusters of semi- and/or non-molten particles or coatings were obtained by, x-ray diffraction, Raman spectroscopy, scanning electron microscopy and nanoindentation. During coating build-up, lower PFR and F/O induce more splat particles and fewer clusters of semi- and/or non-molten particles, whereas the PSD affects the width of the spray trace. The combination of F/O and SOD upper levels was related to a high percentage of TiO2 splat deposition. Finally, the proposed methodology allowed to obtain dense TiO2 coatings with a higher content of rutile phase and an average thickness of 65 µm.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Catalytic Processes in Materials Science · High-Temperature Coating Behaviors · Nuclear Materials and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (61)

Show source-provided references
1. U. Diebold, The Surface Science of Titanium Dioxide, Surf. Sci. Rep., 2003, 48(5-8), p 53-229. https://doi.org/10.1016/S0167-5729(02)00100-010.1016/S0167-5729(02)00100-0 ↗
2. T. Kemmitt, N.I. Al-Salim, M. Waterland, V.J. Kennedy, and A. Markwitz, Photocatalytic Titania Coatings, Curr. Appl. Phys., 2004, 4(2-4), p 189-192. https://doi.org/10.1016/j.cap.2003.11.00610.1016/j.cap.2003.11.006 ↗
3. A.R. Boccaccini, M. Rossetti, J.A. Roether, S.H. Sharif Zein, and M. Ferraris, Development of Titania Coatings on Glass Foams, Constr. Build. Mater., 2009, 23(7), p 2554-2558. https://doi.org/10.1016/j.conbuildmat.2009.02.01910.1016/j.conbuildmat.2009.02.019 ↗
4. M.J. Santillán, N. Quaranta, F. Membrives, J.A. Roether, and A.R. Boccaccini, Processing and Characterization of Biocompatible Titania Coatings by Electrophoretic Deposition, Key Eng. Mater., 2009, 412, p 189-19410.4028/www.scientific.net/KEM.412.189 ↗
5. Y.-P. Lu, M.-S. Li, S.-T. Li, Z.-G. Wang, and R.-F. Zhu, Plasma-Sprayed Hydroxyapatite + Titania Composite Bond Coat for Hydroxyapatite Coating on Titanium Substrate, Biomaterials, 2004, 25(18), p 4393-4403. https://doi.org/10.1016/j.biomaterials.2003.10.0910.1016/j.biomaterials.2003.10.092 ↗
6. M.G. Latorre, Recubrimientos Biocompatibles Obtenidos Por Proyección Térmica y Estudio in Vitro de La Función Osteoblástica, Universitat de Barcelona, Barcelona, 2007
7. R. Tomaszek, L. Pawlowski, L. Gengembre, J. Laureyns, and A. Le Maguer, Microstructure of Suspension Plasma Sprayed Multilayer Coatings of Hydroxyapatite and Titanium Oxide, Surf. Coatings Technol., 2007, 201(16-17), p 7432-7440. https://doi.org/10.1016/j.surfcoat.2007.02.01310.1016/j.surfcoat.2007.02.013 ↗
8. R.B. Heimann, Design of Novel Plasma Sprayed Hydroxyapatite-Bond Coat Bioceramic Systems, J. Therm. Spray Technol., 1999, 8(4), p 597-604. https://doi.org/10.1361/10599639977035030410.1361/105996399770350304 ↗
9. G. Goller, The Effect of Bond Coat on Mechanical Properties of Plasma Sprayed Bioglass-Titanium Coatings, Ceram. Int., 2004, 30(3), p 351-355. https://doi.org/10.1016/S0272-8842(03)00107-X10.1016/S0272-8842(03)00107-X ↗
10. F.N. Oktar, M. Yetmez, S. Agathopoulos, T.M.L. Goerne, G. Goller, I. Ipeker, and J.M.F. Ferreira, Bond-Coating in Plasma-Sprayed Calcium-Phosphate Coatings, J. Mater. Sci. Mater. Med., 2006, 17(11), p 1161-1171. https://doi.org/10.1007/s10856-006-0544-510.1007/s10856-006-0544-5 ↗
11. H. Kurzweg, R.B. Heimann, T. Troczynski, and M.L. Wayman, Development of Plasma-Sprayed Bioceramic Coatings with Bond Coats Based on Titania and Zirconia, Biomaterials, 1998, 19(16), p 1507-1511. https://doi.org/10.1016/S0142-9612(98)00067-210.1016/S0142-9612(98)00067-2 ↗
12. B. Jeffery, M. Peppler, R.S. Lima, and A. McDonald, Bactericidal Effects of HVOF-Sprayed Nanostructured TiO2 on Pseudomonas Aeruginosa, J. Therm. Spray Technol., 2009, 19(1-2), p 344-349. https://doi.org/10.1007/s11666-009-9369-310.1007/s11666-009-9369-3 ↗
13. H. Melero, J. Fernández, S. Dosta, and J.M. Guilemany, Caracterización de Nuevos Recubrimientos Biocompatibles de Hidroxiapatita-TiO2 Obtenidos Mediante Proyección Térmica de Alta Velocidad, Boletín la Soc, Española Cerámica y Vidr., 2011, 50(2), p 59-64. https://doi.org/10.3989/cyv.08201110.3989/cyv.082011 ↗
14. R.S. Lima and B.R. Marple, From APS to HVOF Spraying of Conventional and Nanostructured Titania Feedstock Powders: A Study on the Enhancement of the Mechanical Properties, Surf. Coatings Technol., 2006, 200(11), p 3428-3437. https://doi.org/10.1016/j.surfcoat.2004.10.13710.1016/j.surfcoat.2004.10.137 ↗
15. S. Chandra and P. Fauchais, Formation of Solid Splats during Thermal Spray Deposition, J. Therm. Spray Technol., 2009, 18(2), p 148-180. https://doi.org/10.1007/s11666-009-9294-510.1007/s11666-009-9294-5 ↗
16. P. Bansal, P.H. Shipway, and S.B. Leen, Effect of Particle Impact on Residual Stress Development in HVOF Sprayed Coatings, Proc. Int. Therm. Spray Conf., 2006, 15(December), p 570-575. https://doi.org/10.1361/105996306X14670310.1361/105996306X146703 ↗
17. A.N.N. Sakakibara, H. Tsulcuda, The Splat Morphology of Plasma Sprayed Particle and the Relation to Coating Property, in Thermal Spray 2000: Surface Engineering via Applied Research (2000), p 753-758 (6)10.31399/asm.cp.itsc2000p0753 ↗
18. P. Fauchais, M. Fukumoto, A. Vardelle, and M. Vardelle, Knowledge Concerning Splat Formation: An Invited Review, J. Therm. Spray Technol., 2004, 13(3), p 337-360. https://doi.org/10.1361/1059963041967010.1361/10599630419670 ↗
19. M. Pasandideh-Fard, V. Pershin, S. Chandra, and J. Mostaghimi, Splat Shapes in a Thermal Spray Coating Process: Simulations and Experiments, J. Therm. Spray Technol., 2002, 11(2), p 206-217. https://doi.org/10.1361/10599630277034886210.1361/105996302770348862 ↗
20. H. Ruiz-Luna, D. Lozano-Mandujano, J.M. Alvarado-Orozco, A. Valarezo, C.A. Poblano-Salas, L.G. Trápaga-Martínez, F.J. Espinoza-Beltrán, and J. Muñoz-Saldaña, Effect of HVOF Processing Parameters on the Properties of NiCoCrAlY Coatings by Design of Experiments, J. Therm. Spray Technol., 2014, 23(6), p 950-961. https://doi.org/10.1007/s11666-014-0121-210.1007/s11666-014-0121-2 ↗
21. D. Cheng, Q. Xu, G. Trapaga, and E.J. Lavernia, The Effect of Particle Size and Morphology on the In-Flight, Metall. Mater. Trans. B, 2001, 32(June), p 525-535. https://doi.org/10.1007/s11663-001-0037-310.1007/s11663-001-0037-3 ↗
22. M. Friis and C. Persson, Control of Thermal Spray Processes by Means of Process Maps and Process Windows, J. Therm. Spray Technol., 2003, 12(1), p 44-52. https://doi.org/10.1361/10599630377034849210.1361/105996303770348492 ↗
23. A. Valarezo, W.B. Choi, W. Chi, A. Gouldstone, and S. Sampath, Process Control and Characterization of NiCr Coatings by HVOF-DJ2700 System: A Process Map Approach, J. Therm. Spray Technol., 2010, 19(5), p 852-865. https://doi.org/10.1007/s11666-010-9492-110.1007/s11666-010-9492-1 ↗
24. C. Pierlot, L. Pawlowski, M. Bigan, and P. Chagnon, Design of Experiments in Thermal Spraying: A Review, Surf. Coat. Technol., 2008, 202(18), p 4483-4490. https://doi.org/10.1016/j.surfcoat.2008.04.03110.1016/j.surfcoat.2008.04.031 ↗
25. S. Hasan and J. Stokes, Design of Experiment Analysis of the Sulzer Metco DJ High Velocity Oxy-Fuel Coating of Hydroxyapatite for Orthopedic Applications, J. Therm. Spray Technol., 2010, 20(1-2), p 186-194. https://doi.org/10.1007/s11666-010-9566-010.1007/s11666-010-9566-0 ↗
26. S.M. Forghani, M.J. Ghazali, A. Muchtar, A.R. Daud, N.H.N. Yusoff, and C.H. Azhari, Effects of Plasma Spray Parameters on TiO2-Coated Mild Steel Using Design of Experiment (DoE) Approach, Ceram. Int., 2013, 39(3), p 3121-3127. https://doi.org/10.1016/j.ceramint.2012.09.09210.1016/j.ceramint.2012.09.092 ↗
27. M. Gardon, J.M. Guilemany, The Influence of Titanium Sub-Oxides in Thermal Sprayed Coatings, in Proceedings International Thermal Spray Conference, 2012 (May 2012)10.31399/asm.cp.itsc2012p0622 ↗
28. M. Lufitha, Effect of Substrate Temperature on Coating Adhesion, University of Toronto, Toronto, 2001
29. R.S. Lima and B.R. Marple, Optimized HVOF Titania Coatings, J. Therm., 2003, 12(September), p 360-369. https://doi.org/10.1361/10599630377034823010.1361/105996303770348230 ↗
30. Y. Liu, T.E. Fischer, and A. Dent, Comparison of HVOF and Plasma-Sprayed Alumina/Titania Coatings—Microstructure, Mechanical Properties and Abrasion Behavior, Surf. Coat. Technol., 2003, 167(1), p 68-76. https://doi.org/10.1016/S0257-8972(02)00890-310.1016/S0257-8972(02)00890-3 ↗
31. R.S. Lima and B.R. Marple, High Weibull Modulus HVOF Titania Coatings, J. Therm. Spray Technol., 2003, 12(June), p 240-249. https://doi.org/10.1361/10599630377034835710.1361/105996303770348357 ↗
32. D.L. Perry and S.L. Phillips, Handbook of Inorganic Compounds, CRC Press LLC, Boca Raton, 1995
33. W.C. Oliver and G.M. Pharr, An Improved Technique for Determining Hardness and Elastic Modulus Using Load and Displacement Sensing Indentation Experiments, J. Mater. Res., 1992, 7(6), p 1564-158310.1557/JMR.1992.1564 ↗
34. P. Fauchais, G. Montavon, and G. Bertrand, From Powders to Thermally Sprayed Coatings, J. Therm. Spray Technol., 2010, 19(January), p 56-80. https://doi.org/10.1007/s11666-009-9435-x10.1007/s11666-009-9435-x ↗
35. O.C. Brandt, Mechanical Properties of HVOF Coatings, J. Therm. Spray Technol., 1995, 4(June), p 147-152. https://doi.org/10.1007/BF0264610510.1007/BF02646105 ↗
36. M. Gardon and J.M. Guilemany, Milestones in Functional Titanium Dioxide Thermal Spray Coatings: A Review, J. Therm. Spray Technol., 2014, 23(April), p 577-595. https://doi.org/10.1007/s11666-014-0066-510.1007/s11666-014-0066-5 ↗
37. M. Gaona, R.S. Lima, and B.R. Marple, Influence of Particle Temperature and Velocity on the Microstructure and Mechanical Behaviour of High Velocity Oxy-Fuel (HVOF)-Sprayed Nanostructured Titania Coatings, J. Mater. Process. Technol., 2008, 198(1-3), p 426-435. https://doi.org/10.1016/j.jmatprotec.2007.07.02410.1016/j.jmatprotec.2007.07.024 ↗
38. M. Li, D. Shi, and P.D. Christofides, Modeling and Control of HVOF Thermal Spray Processing of WC–Co Coatings, Powder Technol., 2005, 156(2-3), p 177-194. https://doi.org/10.1016/j.powtec.2005.04.01110.1016/j.powtec.2005.04.011 ↗
39. E. Turunen, T. Varis, S.P. Hannula, A. Vaidya, A. Kulkarni, J. Gutleber, S. Sampath, and H. Herman, On the Role of Particle State and Deposition Procedure on Mechanical, Tribological and Dielectric Response of High Velocity Oxy-Fuel Sprayed Alumina Coatings, Mater. Sci. Eng., A, 2006, 415(1-2), p 1-11. https://doi.org/10.1016/j.msea.2005.08.22610.1016/j.msea.2005.08.226 ↗
40. K. Aik, J. Cizek, K.A. Khor, and I. Dlouhy, In-Flight Temperature and Velocity of Powder Particles of Plasma-Sprayed TiO2, J. Therm. Spray Technol., 2013, 22(8), p 1320-1327. https://doi.org/10.1007/s11666-013-9993-910.1007/s11666-013-9993-9 ↗
41. A.G.M. Pukasiewicz, H.E. de Boer, G.B. Sucharski, R.F. Vaz, and L.A.J. Procopiak, The Influence of HVOF Spraying Parameters on the Microstructure, Residual Stress and Cavitation Resistance of FeMnCrSi Coatings, Surf. Coat. Technol., 2017, 327, p 158-166. https://doi.org/10.1016/j.surfcoat.2017.07.07310.1016/j.surfcoat.2017.07.073 ↗
42. J.A. Hermann-Muñoz, J.A. Rincón-López, G.A. Clavijo-Mejía, A.L. Giraldo-Betancur, J.M. Alvarado-Orozco, A. De Vizcaya-Ruiz, and J. Muñoz-Saldaña, Influence of HVOF Parameters on HAp Coating Generation: An Integrated Approach Using Process Maps, Surf. Coat. Technol., 2019, 358, p 299-307. https://doi.org/10.1016/j.surfcoat.2018.11.02910.1016/j.surfcoat.2018.11.029 ↗
43. G. Mauer, R. Vaben, and D. Stöver, Comparison and Applications of DPV-2000 and Accuraspray-G3 Diagnostic Systems, J. Therm. Spray Technol., 2007, 16(September), p 414-424. https://doi.org/10.1007/s11666-007-9047-210.1007/s11666-007-9047-2 ↗
44. P. Fauchais and A.M. Vardelle, Sensors in Spray Processes, J. Therm. Spray Technol., 2014, 19(4), p 668-694. https://doi.org/10.1007/s11666-010-9485-010.1007/s11666-010-9485-0 ↗
45. J.R. Fincke, D.C. Haggard, and W.D. Swank, Particle Temperature Measurement in the Thermal Spray Process, J. Therm. Spray Technol., 2001, 10, p 255-266. https://doi.org/10.1361/10599630177034935810.1361/105996301770349358 ↗
46. C. Moreau, J. Bisson, R.S. Lima, and B.R. Marple, Diagnostics for Advanced Materials Processing by Plasma Spraying, Pure Appl. Chem., 2005, 77(2), p 443-462. https://doi.org/10.1351/pac20057702044310.1351/pac200577020443 ↗
47. J.W. Jr., W. Tefft, and D.L. Jr., Elastic Constants of Rutile (TiO2), J. Res. Nat. Bur. Stand., 1962, 66(6), p 465-471. https://doi.org/10.6028/jres.066A.04710.6028/jres.066A.047 ↗
48. G.M. Pharr and W.C. Oliver, Measurement of Thin Film Mechanical Properties Using Nanoindentation, MRS Bull., 1992, 17(7), p 28-33. https://doi.org/10.1557/S088376940004163410.1557/S0883769400041634 ↗
49. J.R. Davis, ASM Specialty Handbook ® Stainless Steels, Materials Park, ASM International, 1994, p 584
50. P. Ctibor, P. Boháč, M. Stranyánek, and R. Čtvrtlík, Structure and Mechanical Properties of Plasma Sprayed Coatings of Titania and Alumina, J. Eur. Ceram. Soc., 2006, 26(16), p 3509-3514. https://doi.org/10.1016/j.jeurceramsoc.2005.12.01810.1016/j.jeurceramsoc.2005.12.018 ↗
51. L. Pawlowski, The Science and Engineering of Thermal Spray Coatings, 2nd ed., Wiley, Hoboken, 200810.1002/9780470754085 ↗
52. R. Tomaszek, L. Pawlowski, L. Gengembre, J. Laureyns, Z. Znamirowski, and J. Zdanowski, Microstructural Characterization of Plasma Sprayed TiO2 Functional Coating with Gradient of Crystal Grain Size, Surf. Coat. Technol., 2006, 201(1-2), p 45-56. https://doi.org/10.1016/j.surfcoat.2005.10.03310.1016/j.surfcoat.2005.10.033 ↗
53. I.N. Martyanov, T. Berger, O. Diwald, S. Rodrigues, and K.J. Klabunde, Enhancement of TiO2 Visible Light Photoactivity through Accumulation of Defects during Reduction–Oxidation Treatment, J. Photochem. Photobiol. A Chem., 2010, 212(2-3), p 135-141. https://doi.org/10.1016/j.jphotochem.2010.04.00610.1016/j.jphotochem.2010.04.006 ↗
54. V.V. Sobolev and J.M. Guilemany, Flattening of Droplets and Formation of Splats in Thermal Spraying: A Review of Recent Work—Part 2, J. Therm. Spray Technol., 1999, 8(1), p 87-101. https://doi.org/10.1361/10599639977035061010.1361/105996399770350610 ↗
55. M. Vardelle, A. Vardelle, A.C. Leger, P. Fauchais, and D. Gobin, Influence of Particle Parameters at Impact on Splat Formation and Solidification in Plasma Spraying Processes, J. Therm. Spray Technol., 1994, 4(March), p 50-58. https://doi.org/10.1007/BF0264852810.1007/BF02648528 ↗
56. H. Fukanuma, R. Huang, Y. Tanaka, and Y. Uesugi, Mathematical Modeling and Numerical Simulation of Splat Cooling in Plasma Spray Coatings, J. Therm. Spray Technol., 2009, 18(December), p 965-974. https://doi.org/10.1007/s11666-009-9366-610.1007/s11666-009-9366-6 ↗
57. Z. Zhu, K. Spyros, and S. Gu, Numerical Study of Molten and Semi-Molten Ceramic Impingement by Using Coupled Eulerian and Lagrangian Method, Acta Mater., 2015, 90(March), p 77-87. https://doi.org/10.1016/j.actamat.2015.02.01010.1016/j.actamat.2015.02.010 ↗
58. M. Bertagnolli, M. Marchese, G. Jacucci, S.D. Ioannis, and S. Noelting, Thermomechanical Simulation of the Splashing of Ceramic Droplets on a Rigid Substrate, J. Comput. Phys., 1997, 133(2), p 205-221. https://doi.org/10.1006/jcph.1996.546810.1006/jcph.1996.5468 ↗
59. L. Li, A. Vaidya, S. Sampath, H. Xiong, and L. Zheng, Particle Characterization and Splat Formation of Plasma Sprayed Zirconia, J. Therm. Spray Technol., 2006, 15(March), p 97-105. https://doi.org/10.1361/105996306X9266810.1361/105996306X92668 ↗
60. K. Yang, M. Liu, K. Zhou, and C. Deng, Recent Developments in the Research of Splat Formation Process in Thermal Spraying, J. Mater., 2013, 2013, p 1-1410.1155/2013/260758 ↗
61. T. Itsukaichi, S. Osawa, and R. Ahmed, Influence of Powder Size and Strength on HVOF Spraying—Mapping the Onset of Spitting, in Thermal Spray 2003 Advanced Science Application Technology (2003), p 819-824.10.31399/asm.cp.itsc2003p0819 ↗