journal article·2020-12

Effect of the Corrosion of Seal Coatings Used in Aero Engines on Their High-Speed Wear Behaviour

Jiaping Zhang, Weihai Xue, Deli Duan, Shengli Jiang, Jia Song, Siyang Gao, Shu Li

Publisher page

Abstract

As the number of aircraft that park in ocean environments increases, the corrosion of coatings used in their engines becomes inevitable. Previous studies have focussed on the abradability of as-sprayed seal coatings in high-speed rubbing tests with a blade. This study deals with the investigation of the effect of corrosion on the abradability of seal coatings. It uses metallographic analysis and hardness, bonding strength and high-speed rubbing tests conducted on as-sprayed and corroded Al-hBN coatings. The results have shown the appearance of additional pores in the corroded coatings and a decrease in the coating mechanical properties. Compared with the as-sprayed coatings, the corroded coatings caused an increase in blade wear and severe overheating of the blade tip during the high-speed rubbing test when the rubbing speed and single-pass depth were high. The unfavourable thermal properties of the corroded coatings were considered as the probable reason for these results.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Material Properties and Applications · Surface Treatment and Coatings · Tribology and Wear Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (19)

Show source-provided references
1. R.E. Chupp, R.C. hendricks, S.B. Lattime, and B.M. Steinetz, Sealing in Turbomachine. NASS/TM-2006-214341, 2006
2. R.C. Bill and L.P. Ludwig, Wear of Seal Materials Used in Aircraft Propulsion Systems, Wear, 1980, 59(1), p 165-18910.1016/0043-1648(80)90277-X ↗
3. L.T. Shiembob, Development of Abradable Gas Path Seals. NASA Contract. Rep., CR-134689, 1974
4. L.P. Ludwig and R.C. Bill, Gas Path Sealing in Turbine Engines, Tribol. Trans., 1980, 23(1), p 1-22
5. J. Stringer and M.B. Marshall, High Speed Wear Testing of an Abradable Coating, Wear, 2012, 294–295, p 257-26310.1016/j.wear.2012.07.009 ↗
6. N. Fois, J. Stringer, and M.B. Marshall, Adhesive Transfer in Aero-engine Abradable Linings Contact, Wear, 2013, 304(1–2), p 202-21010.1016/j.wear.2013.04.033 ↗
7. W.H. Xue, S.Y. Gao, D.L. Duan, Y. Liu, and S. Li, Material Transfer Behaviour Between a Ti6Al4V Blade and an Aluminium Hexagonal Boron Nitride Abradable Coating During High-Speed Rubbing, Wear, 2015, 322–323, p 76-9010.1016/j.wear.2014.10.001 ↗
8. S.Y. Gao, W.H. Xue, D.L. Duan, and S. Li, Tribological Behaviors of Turbofan Seal Couples from Friction Heat Perspective Under High-Speed Rubbing Condition, Friction, 2016, 4(2), p 176-19010.1007/s40544-016-0114-x ↗
9. C.G. Xu, L.Z. Du, B. Yang, and W.G. Zhang, The Effect of Al Content on the Galvanic Corrosion Behaviour of Coupled Ni/Graphite and Ni–Al Coatings, Corros. Sci., 2011, 53(6), p 2066-207410.1016/j.corsci.2011.02.019 ↗
10. B. Lei, M. Li, Z.X. Zhao, L. Wang, Y. Li, and F.H. Wang, Corrosion Mechanism of an Al-BN Abradable Seal Coating System in Chloride Solution, Corros. Sci., 2014, 79, p 198-20510.1016/j.corsci.2013.11.007 ↗
11. F. Zhang, C.G. Xu, H. Lan, C.B. Huang, Y. Zhou, L.Z. Du, and W.G. Zhang, Corrosion Behavior of an Abradable Seal Coating System, J. Therm. Spray Technol., 2014, 23(6), p 1019-102810.1007/s11666-014-0115-0 ↗
12. L. Li and X. Su, Corrosion Behavior of Aluminum Alloy 1050A During Cyclic Wet-Dry Immersion Test in Simulated Marine Atmospheric Enviroment, Corros. Sci. Prot. Technol., 2014, 04, p 367-386 ((in Chinese))10.1016/j.corsci.2014.03.005 ↗
13. B. Lei, S.N. Hu, Z.H. Wang, Y. Li, and F.H. Wang, Corrosion-Detection and Assessment Methods for Abradable Sealing Coatings, Corros. Sci. Prot. Technol., 2017, 06, p 651-656 ((in Chinese))
14. D.M. William, A Phenomenological Model of Abradable Wear in High Performance Turbomachinery, Wear, 1980, 59(1), p 191-21110.1016/0043-1648(80)90278-1 ↗
15. N. Fois, M. Watson, and M. Marshall, The Influence of Material Properties on the Wear of Abradable Materials, in Proceedings of the Institution of Mechanical Engineers. Part J, Journal of Engineering Tribology, 201610.1177/1350650116649528 ↗
16. W.H. Xue, S.Y. Gao, D.L. Duan, J.P. Zhang, Y. Liu, and S. Li, Effects of Blade Material Characteristics on the High-Speed Rubbing Behavior Between Al-hBN Abradable Seal Coatings and Blades, Wear, 2018, 410–411, p 25-3310.1016/j.wear.2018.06.003 ↗
17. J.F. Archard, The Temperature of Rubbing Surfaces, Wear, 1959, 2(6), p 438-45510.1016/0043-1648(59)90159-0 ↗
18. J. Porntadawit, V. Uthaisangsuk, and P. Choungthong, Modeling of Flow Behavior of Ti–6Al–4V Alloy at Elevated Temperatures, Mater. Sci. Eng. A-Struct. Mater. Prop. Microstruct. Process., 2014, 599, p 212-22210.1016/j.msea.2014.01.064 ↗
19. R. Ding, Z.X. Guo, and A. Wilson, Microstructural Evolution of a Ti–6Al–4V Alloy During Thermomechanical Processing, Mater. Sci. Eng. A-Struct. Mater. Prop. Microstruct. Process., 2002, 327(2), p 233-24510.1016/S0921-5093(01)01531-3 ↗