Effect of Dimensions of Non-bonded Lamellar Interfaces on the Stress Distribution in APS-TBCs
Source abstract
Abstract
Cracking behavior has been considered for the top coating in the thermal barrier coating system. The effect of the dimension and position of non-bonded lamellar interfaces on the stress distribution is investigated by the simulation method. Plasma-sprayed yttria-stabilized zirconia coatings are deposited at different spraying distances. The crack propagation behavior is studied by statistical analysis after the coatings have experienced different thermal cycles. The simulation results reveal that the normal stresses at the tips of non-bonded lamellar interfaces increase with the increment of the length of interfaces and with the decrease of the distance between them. The stress level almost stays the same with the changing of lamellar thickness. Experimental results indicate the correctness of the simulation. It is found that the length of non-bonded lamellar interfaces in the as-deposited coatings shows an increasing tendency with the spraying distance. The total crack length of coatings increases with the number of thermal cycles and the spraying distance after thermal cycling tests.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Nuclear Materials and Properties · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. N.P. Padture, M. Gell, and E.H. Jordan, Thermal Barrier Coatings for Gas-Turbine Engine Applications, Science, 2002, 296(5566), p 280-28410.1126/science.1068609 ↗
2. A.G. Evans, D.R. Mumm, J.W. Hutchinson, G.H. Meier, and F.S. Pettit, Mechanisms Controlling the Durability of Thermal Barrier Coatings, Prog. Mater Sci., 2001, 46(5), p 505-55310.1016/S0079-6425(00)00020-7 ↗
3. J.R. Nicholls, Advances in Coating Design for High-Performance Gas Turbines, MRS Bull., 2003, 28(09), p 659-67010.1557/mrs2003.194 ↗
4. K.W. Schlichting, N.P. Padture, E.H. Jordan, and M. Gell, Failure Modes in Plasma-Sprayed Thermal Barrier Coatings, Mater. Sci. Eng. A, 2003, 342(1), p 120-13010.1016/S0921-5093(02)00251-4 ↗
5. M. Ranjbar-Far, J. Absi, and G. Mariaux, Finite Element Modeling of the Different Failure Mechanisms of a Plasma Sprayed Thermal Barrier Coatings System, J. Therm. Spray Technol., 2012, 21(6), p 1234-124410.1007/s11666-012-9814-6 ↗
6. C.J. Li, Y. Li, G.J. Yang, and C.X. Li, Evolution of Lamellar Interface Cracks During Isothermal Cyclic Test of Plasma-Sprayed 8YSZ Coating with a Columnar-Structured YSZ Interlayer, J. Therm. Spray Technol., 2013, 22(8), p 1374-138210.1007/s11666-013-9965-0 ↗
7. Y. Liu, C. Persson, and S. Melin, Fracture Mechanics Analysis of Microcracks in Thermally Cycled Thermal Barrier Coatings, J. Therm. Spray Technol., 2004, 13(3), p 377-38010.1361/10599630420407 ↗
8. L.L. Shaw, B. Barber, E.H. Jordan, and M. Gell, Measurements of the Interfacial Fracture Energy of Thermal Barrier Coatings, Scripta Mater., 1998, 39(10), p 1427-143410.1016/S1359-6462(98)00292-9 ↗
9. W.Z. Wang and C.J Li, Relationships Between the Microstructure and Mechanical Properties of Plasma-Sprayed Coatings, J. Press. Equip. Syst., 2005, 3, p 93-101
10. C.J. Li, C.X. Li, and M. Wang, Effect of Spray Parameters on the Electrical Conductivity of Plasma-Sprayed LA1−x Sr x MnO3 Coating for the Cathode of SOFCs, Surf. Coat. Technol., 2005, 198, p 278-28210.1016/j.surfcoat.2004.10.083 ↗
11. C.J. Li, G.J. Yang, and A. Ohmori, Relationship Between Particle Erosion and Lamellar Microstructure for Plasma Sprayed Alumina Coatings, Wear, 2006, 260, p 1166-117210.1016/j.wear.2005.07.006 ↗
12. M. Ranjbar-Far, J. Absi, G. Mariaux, and D.S. Smith, Crack Propagation Modeling on the Interfaces of Thermal Barrier Coating System with Different Thickness of the Oxide Layer and Different Interface Morphologies, Mater. Des., 2011, 32(10), p 4961-496910.1016/j.matdes.2011.05.039 ↗
13. C.J. Li and A. Ohmori, Relationships Between the Microstructure and Properties of Thermally Sprayed Deposits, J. Therm. Spray Technol., 2002, 11(3), p 365-37410.1361/105996302770348754 ↗
14. C.J. Li, A. Ohmori, and R. McPherson, The Relationship Between Microstructure and Young’s Modulus of Thermally Sprayed Ceramic Coatings, J. Mater. Sci., 1997, 32(4), p 997-100410.1023/A:1018574221589 ↗
15. C.J. Li and W.Z. Wang, Quantitative Characterization of Lamellar Microstructure of Plasma-Sprayed Ceramic Coatings Through Visualization of Void Distribution, Mater. Sci. Eng. A, 2004, 386(1), p 10-19
16. J. Rösler, M. Bäker, and M. Volgmann, Stress State and Failure Mechanisms of Thermal Barrier Coatings: Role of Creep in Thermally Grown Oxide, Acta Mater., 2001, 49(18), p 3659-367010.1016/S1359-6454(01)00283-X ↗
17. M. Białas, Finite Element Analysis of Stress Distribution in Thermal Barrier Coatings, Surf. Coat. Technol., 2008, 202(24), p 6002-601010.1016/j.surfcoat.2008.06.178 ↗
18. M. Ahrens, R. Vaßen, and D. Stöver, Stress Distributions in Plasma-Sprayed Thermal Barrier Coatings as a Function of Interface Roughness and Oxide Scale Thickness, Surf. Coat. Technol., 2002, 161(1), p 26-3510.1016/S0257-8972(02)00359-6 ↗
19. A.M. Freborg, B.L. Ferguson, W.J. Brindley, and G.J. Petrus, Modeling Oxidation Induced Stresses in Thermal Barrier Coatings, Mater. Sci. Eng. A, 1998, 245(2), p 182-19010.1016/S0921-5093(97)00849-6 ↗
20. R. McPherson and B.V. Shafer, Interlamellar Contact Within Plasma-Sprayed Coatings, Thin Solid Films, 1982, 97(3), p 201-20410.1016/0040-6090(82)90453-9 ↗
21. H. Yuan and J. Chen, Computational Analysis of Thin Coating Layer Failure Using a Cohesive Model and Gradient Plasticity, Eng. Fract. Mech., 2003, 70(14), p 1929-194210.1016/S0013-7944(03)00132-2 ↗
22. A. Rabiei and A.G. Evans, Failure Mechanisms Associated with the Thermally Grown Oxide in Plasma-Sprayed Thermal Barrier Coatings, Acta Mater., 2000, 48(15), p 3963-397610.1016/S1359-6454(00)00171-3 ↗
23. ABAQUS Version 6.10, User Documentation, Deassault Systèmes, 2010
24. W. Xie, E. Jordan, and M. Gell, Stress and Cracking Behavior of Plasma Sprayed Thermal Barrier Coatings Using An Advanced Constitutive Model, Mater. Sci. Eng. A, 2006, 419(1), p 50-5810.1016/j.msea.2005.11.060 ↗
25. C.G. Zhou, N. Wang, and H.B. Xu, Comparison of Thermal Cycling Behavior of Plasma-Sprayed Nanostructured and Traditional Thermal Barrier Coatings, Mater. Sci. Eng. A, 2007, 452, p 569-57410.1016/j.msea.2006.11.027 ↗
26. H.B. Xu and H.B. Guo, Thermal Barrier Coatings, Elsevier, Amsterdam, 201110.1533/9780857090829 ↗
27. M. Ranjbar-Far, J. Absi, S. Shahidi, and G. Mariaux, Impact of the Non-homogenous Temperature Distribution and the Coatings Process Modeling on the Thermal Barrier Coatings System, Mater. Des., 2011, 33(2), p 728-73510.1016/j.matdes.2010.07.034 ↗
28. A. Ohmori and C.J. Li, Quantitative Characterization of the Structure of Plasma-Sprayed Al2O3 Coating by Using Copper Electroplating, Thin Solid Films, 1991, 201(2), p 241-25210.1016/0040-6090(91)90114-D ↗
29. A. Ohmori, C.J. Li, and Y. Arata, Influence of Plasma Spray Conditions on the Structure of Al2O3 Coatings, Trans. Jpn. Weld. Res. Inst., 1990, 19, p 259-270
30. ASTM C1525-02, Standard Test Method for Determination of Thermal Shock Resistance for Advanced Ceramics by Water Quenching, Annual Book of ASTM Standards, ASTM International, PA, 2002
31. A.N. Khan and J. Lu, Behavior of Air Plasma Sprayed Thermal Barrier Coatings, Subject to Intense Thermal Cycling, Surf. Coat. Technol., 2003, 166(1), p 37-4310.1016/S0257-8972(02)00740-5 ↗
32. L. Wang, Y. Wang, W.Q. Zhang, X.G. Sun, J.Q. He, Z.Y. Pan, and C.H. Wang, Finite Element Simulation of Stress Distribution and Development in 8YSZ and Double-Ceramic-Layer La2Zr2O7/8YSZ Thermal Barrier Coatings During Thermal Shock, Appl. Surf. Sci., 2012, 258(8), p 3540-355110.1016/j.apsusc.2011.11.109 ↗
33. M.R. Loghman-Estarki, R. ShojaRazavi, H. Edris, and H. Jamali, Life Time of New SYSZ Thermal Barrier Coatings Produced by Plasma Spraying Method Under Thermal Shock Test and High Temperature Treatment, Ceram. Int., 2014, 40(1), p 1405-141410.1016/j.ceramint.2013.07.023 ↗
34. P.L. Ke, Q.M. Wang, M.H. Guo, J. Gong, C. Sun, and Y.C. Zhou, Failure Mechanism of D-Gun Sprayed Thermal Barrier Coatings Subjected to Thermal Shock Cycling, Mater. Sci. Forum, 2005, 475, p 3977-3980
35. R. McPherson, The Relationship Between the Mechanism of Formation, Microstructure and Properties of Plasma Sprayed Coating, Thin Solid Films, 1981, 83(3), p 297-31010.1016/0040-6090(81)90633-7 ↗
36. Y. Joliff, J. Absi, M. Huger, and J.C. Glandus, Experimental and Numerical Study of the Elastic Modulus Vs Temperature of Debonded Model Materials, Comput. Mater. Sci., 2008, 44(2), p 826-83110.1016/j.commatsci.2008.04.024 ↗
37. Y. Liu, C. Persson, and S. Melin, Numerical Modeling of Short Crack Behavior in a Thermal Barrier Coating Upon Thermal Shock Loading, J. Therm. Spray Technol., 2004, 13(4), p 554-56010.1361/10599630421488 ↗