journal article·2023-02

Properties of Multilayered Metallic Coatings Deposited on Carbon Fiber-Reinforced Polymers (CFRPs) through Electrochemical and Cold Spray Processes

Panteha Fallah, Sima A. Alidokht, Phuong Vo, Richard R. Chromik, André McDonald, Stephen Yue

Publisher page

Abstract

Previous studies have shown that copper (Cu) may be cold spray deposited on epoxy carbon fiber-reinforced polymers (CFRPs) if an interlayer Cu of electroplated on an electroless nickel (Ni) coating is present prior to cold spraying. In this present study, the tensile adhesion bond strength of these multilayered metallic coatings was measured in accordance with ASTM Standard C-633-13. Fractured surfaces after tensile adhesion testing were examined by scanning electron microscopy (SEM) and optical microscopy (OM). Scratch adhesion testing from the polished cross sections of the multilayered coatings was also performed to compare the results with those obtained from the tensile adhesion testing. The microstructure of the cold-sprayed and electroplated Cu coatings was analyzed by electron channeling contrast imaging (ECCI), and its correlation with hardness values was studied. Adhesive failure at the Ni coating/CFRP interface was observed in the absence of a cold-sprayed Cu coating. Enhanced bonding between electroless Ni coating and exposed carbon fiber areas was observed relative to the epoxy regions. This enhanced bonding was attributed to the increased roughness of the carbon fiber regions relative to the epoxy areas. However, after cold spraying with Cu, cohesive failure of the cold-sprayed Cu coating occurred, which was likely due to insufficient plastic deformation of the particles cold sprayed close to the critical velocity of Cu. Electron channeling contrast imaging analysis from the cross sections revealed uniform and inhomogeneous microstructures within the electroplated and cold-sprayed Cu coatings, respectively.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Metal and Thin Film Mechanics · Corrosion Behavior and Inhibition

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (58)

Show source-provided references
1. U.S. Department of Transportation Federal Aviation Administration, Aviation Maintenance Technician Handbook—Airframe Vol. 1 (2012)
2. J. Siegel and V. Kotál, Preparation of Thin Metal Layers on Polymers, Acta Polytech., 2007 https://doi.org/10.14311/90410.14311/904 ↗
3. T. Duguet, F. Senocq, L. Laffont and C. Vahlas, Metallization of Polymer Composites by Metalorganic Chemical Vapor Deposition of Cu: Surface Functionalization Driven Films Characteristics, Surf. Coat. Technol., 2013, 230, p 254-259.10.1016/j.surfcoat.2013.06.065 ↗
4. S. Kuroda, J. Kawakita, M. Watanabe and H. Katanoda, Warm Spraying—A Novel Coating Process Based on High-Velocity Impact of Solid Particles, Sci. Technol. Adv. Mater., 2008, 9(3), p 17.10.1088/1468-6996/9/3/033002 ↗
5. C. Katsoulis, B.K. Kandola, P. Myler and E. Kandare, Post-Fire Flexural Performance of Epoxy-Nanocomposite Matrix Glass Fibre Composites Containing Conventional Flame Retardants, Compos. Part A Appl. Sci., 2012, 43(8), p 1389-1399.10.1016/j.compositesa.2012.03.009 ↗
6. J. Affi, H. Okazaki, M. Yamada and M. Fukumoto, Fabrication of Aluminum Coating onto CFRP Substrate by Cold Spray, Mater. Trans., 2011, 52(1), p 1759-1763.10.2320/matertrans.T-M2011807 ↗
7. N. Huonnic, M. Abdelghani, P. Mertiny and A. McDonald, Deposition and Characterization of Flame-Sprayed Aluminum on Cured Glass and Basalt Fiber-Reinforced Epoxy Tubes, Surf. Coat. Technol., 2010, 205(3), p 867-873.10.1016/j.surfcoat.2010.08.029 ↗
8. R. Gonzalez, H. Ashrafizadeh, A. Lopera, P. Mertiny and A. McDonald, A Review of Thermal Spray Metallization of Polymer-Based Structures, J. Therm. Spray Technol., 2016, 25(5), p 897-919.10.1007/s11666-016-0415-7 ↗
9. S. Kuroda, J. Kawakita, M. Watanabe, K.H. Kim, R. Molak and H. Katanoda, Current Status and Future Prospects of Warm Spray Technology, Future Development of Thermal Spray Coatings. Woodhead Publishing, 2015, p 163-206. https://doi.org/10.1016/B978-0-85709-769-9.00007-510.1016/B978-0-85709-769-9.00007-5 ↗
10. C. Chen, X. Xie, Y. Xie, X. Yan, G. Huang, S. Deng, Z. Ren and H. Liao, Metallization of Polyether Ether Ketone (PEEK) by Copper Coating via Cold Spray, Surf. Coat. Technol., 2018, 342, p 209-219.10.1016/j.surfcoat.2018.02.087 ↗
11. A. Papyrin, V. Kosarev, S. Klinkov, A. Alkhimov and V.M. Fomin, Cold Spray Technology, Elsevier, 2007.
12. V.K. Champagne, The Cold Spray Materials Deposition Process: Fundamentals and Applications, Elsevier, 2007.10.1201/9781439824122 ↗
13. H. Che, P. Vo and S. Yue, Metallization of carbon Fibre Reinforced Polymers by Cold Spray, Surf. Coat. Technol., 2017, 313, p 236-247.10.1016/j.surfcoat.2017.01.083 ↗
14. A. Ganesan, M. Yamada and M. Fukumoto, Cold spray Coating Deposition Mechanism on the Thermoplastic and Thermosetting Polymer Substrates, J. Therm. Spray Technol., 2013, 22(8), p 1275-1282.10.1007/s11666-013-9984-x ↗
15. H. Che, P. Vo and S. Yue, Metallization of various polymers by cold spray, J. Therm. Spray Technol., 2017, 27(1-2), p 169-178.10.1007/s11666-017-0663-1 ↗
16. P. Lomonaco, S. Weiller, I. Feki, A. Debray, F. Delloro, M. Jeandin, B. Favini and C. Rossignol, Cold Spray Technology to Promote Conductivity of Short Carbon Fiber Reinforced Polyether-Ether-Ketone (PEEK), Key Eng. Mater., 2019, 813, p 459-464.10.4028/www.scientific.net/KEM.813.459 ↗
17. V. Gillet, E. Aubignat, S. Costil, B. Courant, C. Langlade, P. Casari, W. Knapp and M.P. Planche, Development of Low Pressure Cold Sprayed Copper Coatings on Carbon Fiber Reinforced Polymer (CFRP), Surf. Coat. Technol., 2019, 364, p 306-316.10.1016/j.surfcoat.2019.01.011 ↗
18. R. Della Gatta, A. Viscusi, A.S. Perna, A. Caraviello and A. Astarita, Feasibility of Steel Powder Deposition on Composites Through Cold Spray, Mater. Manuf. Process., 2020, 36(3), p 281-291.10.1080/10426914.2020.1832693 ↗
19. M. Barletta, A. Gisario and V. Tagliaferri, Electrostatic Spray Deposition (ESD) of Polymeric Powders on Thermoplastic (PA66) Substrate, Surf. Coat. Technol., 2006, 201(1-2), p 296-308.10.1016/j.surfcoat.2005.11.120 ↗
20. G. Archambault, B. Jodoin, S. Gaydos and M. Yandouzi, Metallization of Carbon Fiber Reinforced Polymer Composite by Cold Spray and Lay-up Molding Processes, Surf. Coat. Technol., 2016, 300, p 78-86.10.1016/j.surfcoat.2016.05.008 ↗
21. A. Ganesan, J. Affi, M. Yamada and M. Fukumoto, Bonding Behavior Studies of Cold Sprayed Copper Coating on the PVC Polymer Substrate, Surf. Coat. Technol., 2012, 207, p 262-269.10.1016/j.surfcoat.2012.06.086 ↗
22. M. Chen, Surface preparation of polymeric substrates for cold spraying coatings, Masters thesis, McGill University (2022)
23. A. Liberati, Mechanisms affecting the metallization of carbon fiber reinforced polymers through the cold spraying of Sn-based mixed metal powders, Ph.D. thesis, McGill University (2022)
24. A.C. Liberati, H. Che, P. Fallah, P. Vo and S. Yue, Pull-off Testing and Electrical Conductivity of Sn-Based Metal Powder Mixtures Cold Sprayed on Carbon Fiber-Reinforced Polymers, J. Therm. Spray Technol., 2022 https://doi.org/10.1007/s11666-022-01405-010.1007/s11666-022-01405-0 ↗
25. A. Małachowska, M. Winnicki, Ł Konat, T. Piwowarczyk, L. Pawłowski, A. Ambroziak and M. Stachowicz, Possibility of Spraying of Copper Coatings on Polyamide 6 with Low Pressure Cold Spray Method, Surf. Coat. Technol., 2017, 318, p 82-89.10.1016/j.surfcoat.2017.02.001 ↗
26. A. Rezzoug, S. Abdi, A. Kaci and M. Yandouzi, Thermal Spray Metallisation of Carbon Fibre Reinforced Polymer Composites: Effect of Top Surface Modification on Coating Adhesion and Mechanical Properties, Surf. Coat. Technol., 2018, 333, p 13-23.10.1016/j.surfcoat.2017.10.066 ↗
27. P. Fallah, S. Rajagopalan, A. McDonald and S. Yue, Development of Hybrid Metallic Coatings on Carbon Fiber-Reinforced Polymers (CFRPs) by Cold Spray Deposition of Copper-Assisted Copper Electroplating Process, Surf. Coat. Technol., 2020, 400, p 126231.10.1016/j.surfcoat.2020.126231 ↗
28. P. Fallah, R. Chakrabarty, J. Song, A. McDonald and S. Yue, Effect of Metallic Interlayer Hardness on Deposition Characteristics of Cold-Sprayed Copper Particles on Carbon Fiber-Reinforced Polymers, J. Therm. Spray Technol., 2022, 31(3), p 559-573.10.1007/s11666-021-01313-9 ↗
29. ASTM, ASTM C 633—Standard Test Method for Adhesion or Cohesion Strength of Thermal Spray Coatings. Annual Book of ASTM Standards (2008)
30. International A, ASTM C633-13, Standard Test Method for Adhesion or Cohesion Strength of Thermal Spray Coatings. 2017: West Conshohocken, PA
31. ISO-ISO 27307:2015, Thermal spraying—Evaluation of adhesion/cohesion of thermal sprayed ceramic coatings by transverse scratch testing
32. M. Cailler and G.H. Lee, Scratch Adhesion Test of Magnetron-Sputtered Copper Coatings on Aluminium Substrates: Effects of the Surface Preparation, Thin Solid Films, 1989, 168(2), p 193-205.10.1016/0040-6090(89)90006-0 ↗
33. M. Schlesinger and M. Paunovic, Modern Electroplating, 5th ed. John Wiley & Sons, 2014.
34. G.O. Mallory and J.B. Hajdu, Electroless Plating: Fundamentals and Applications, William Andrew, 1990.
35. P. Bindra, Mechanisms of Electroless Metal Plating, J. Electrochem. Soc., 1983, 130(11), p 1112.10.1149/1.2119895 ↗
36. S.J. Yu, L.X. Song, Y.S. Huang, R.G. Zhao, X.F. Hu, Electroless Ni-P-SiC Composite Coating. Inorg. Mater. 19(3) (2004)
37. J.N. Balaraju, P. Radhakrishnan, V. Ezhilselvi, A.A. Kumar, Z. Chen and K.P. Surendran, Studies on Electroless Nickel Polyalloy Coatings Over Carbon Fibers/CFRP Composites, Surf. Coat. Technol., 2016, 302, p 389-397.10.1016/j.surfcoat.2016.06.040 ↗
38. R. Agarwala, V. Agarwala and R. Sharma, Electroless Ni-P Based Nanocoating Technology—A Review, Synthesis and Reactivity in Inorganic, Inorg. Nano Met. Chem., 2006, 36(6), p 493-515.10.1080/15533170600596030 ↗
39. J.N. Balaraju and K.S. Rajam, Electroless Deposition of Ni-Cu-P, Ni-W-P and Ni-W-Cu-P Alloys, Surf. Coat. Technol., 2005, 195(2-3), p 154-161.10.1016/j.surfcoat.2004.07.068 ↗
40. K. Yamagishi, N. Okamoto, N. Mitsumata, N. Fukumuro, S. Yae and H. Matsuda, Reaction process of two-step Catalysation Pre-treatment for Electroless Plating on Non-conducting Substrates, Trans. Inst. Met. Finish., 2004, 82(3-4), p 114-117.10.1080/00202967.2004.11871571 ↗
41. H. Jüntgen, Activated Carbon as Catalyst Support: A Review of New Research Results, Fuel, 1986, 65(10), p 1436-1446.10.1016/0016-2361(86)90120-1 ↗
42. E. Lam and J.H.T. Luong, Carbon Materials as Catalyst Supports and Catalysts in the Transformation of Biomass to Fuels and Chemicals, ACS Catal., 2014, 4(10), p 3393-3410.10.1021/cs5008393 ↗
43. M. Luty-Błocho, M. Wojnicki, K. Pacławski and K. Fitzner, The Synthesis of Platinum Nanoparticles and their Deposition on the Active Carbon Fibers in One Microreactor Cycle, Chem. Eng. J., 2013, 226, p 46-51.10.1016/j.cej.2013.04.008 ↗
44. M. Charbonnier and M. Romand, Polymer Pretreatments for Enhanced Adhesion of Metals Deposited by the Electroless Process, Int. J. Adhes. Adhes., 2003, 23(4), p 277-285.10.1016/S0143-7496(03)00045-9 ↗
45. C.K. Lee, Structure, Electrochemical and Wear-Corrosion Properties of Electroless Nickel-Phosphorus Deposition on CFRP Composites, Mater. Chem. Phys., 2009, 114(1), p 125-133.10.1016/j.matchemphys.2008.08.088 ↗
46. J.E. Van Den Meerakker, On the Mechanism of Electroless Plating. II. One Mechanism for Different Reductants, J. Appl. Electrochem., 1981, 11(3), p 395-400.10.1007/BF00613960 ↗
47. S. Wei, X. Zhan, Y. Wen, Y. Li, Z. Zhang, F. Wu and C. Wang, Deposition Mechanism of Electroless Nickel Plating of Composite Coatings on Magnesium Alloy, Chem. Eng. Sci., 2019, 207, p 1299-1308.10.1016/j.ces.2019.07.048 ↗
48. S.J. Bull, Failure Modes in Scratch Adhesion Testing, Surf. Coat. Technol., 1991, 50(1), p 25-32.10.1016/0257-8972(91)90188-3 ↗
49. R.F. Váz et al., Fretting Wear and Scratch Resistance of Cold-Sprayed Pure Cu and Ti, Metallogr. Microstruct. Anal., 2021, 10(4), p 496-513.10.1007/s13632-021-00758-2 ↗
50. V. Aleksandar, S. Arostegui, G. Favaro, F. Zivic, M. Mrdak, S. Mitrović and V. Popovic, Evaluation of Adhesion/Cohesion Bond Strength of the Thick Plasma Spray Coatings by Scratch Testing on Coatings Cross-Sections, Tribol. Int., 2011, 44(11), p 1281-1288.10.1016/j.triboint.2011.04.002 ↗
51. T. Liu, J.D. Leazer and L.N. Brewer, Particle Deformation and Microstructure Evolution During Cold Spray of Individual Al-Cu Alloy Powder Particles, Acta Mater., 2019, 168, p 13-23.10.1016/j.actamat.2019.01.054 ↗
52. M.R. Rokni, S.R. Nutt, C.A. Widener, V.K. Champagne and R.H. Hrabe, Review of Relationship Between Particle Deformation, Coating Microstructure, and Properties in High-Pressure Cold Spray, J. Therm. Spray Technol., 2017, 26, p 1308-1355.10.1007/s11666-017-0575-0 ↗
53. T. Schmidt, F. Gärtner, H. Assadi and H. Kreye, Development of a Generalized Parameter Window for Cold Spray Deposition, Acta Mater., 2006, 54(3), p 729-742.10.1016/j.actamat.2005.10.005 ↗
54. M. Hamdi, M.N. Saleh and J.A. Poulis, Improving the Adhesion Strength of Polymers: Effect of Surface Treatments, J. Adhes. Sci. Technol., 2020, 34(17), p 1853-1870.10.1080/01694243.2020.1732750 ↗
55. A. Vencl et al., Evaluation of Adhesion/Cohesion Bond Strength of the Thick Plasma Spray Coatings by Scratch Testing on Coatings Cross-Sections, Tribol. Int., 2011, 44(11), p 1281-1288.10.1016/j.triboint.2011.04.002 ↗
56. C. Borchers, R. Gärtner, T. Stoltenhoff and H. Kreye, Microstructural Bonding Features of Cold Sprayed Face Centered Cubic Metals, J. Appl. Phys., 2004, 96(8), p 4288.10.1063/1.1789278 ↗
57. V.N.V. Munagala, V. Akinyi, P. Vo and R.R. Chromik, Influence of Powder Morphology and Microstructure on the Cold Spray and Mechanical Properties of Ti6Al4V Coatings, J. Therm. Spray Technol., 2018, 27(5), p 827-842.10.1007/s11666-018-0729-8 ↗
58. Y. Zou, D. Goldbaum, J.A. Szpunar and S. Yue, Microstructure and Nanohardness of Cold-Sprayed Coatings: Electron Backscattered Diffraction and Nanoindentation Studies, Scr. Mater., 2010, 62(6), p 395-398.10.1016/j.scriptamat.2009.11.034 ↗