Exploring Miniaturized HVOF Systems for the Deposition of Ti-6Al-4V
Source abstract
Abstract
Abstract The exceptional properties of Ti-6Al-4V of high strength, lightweight, corrosion resistance and machinability make it one of the most widely used alloys in in the aerospace industry. Significant efforts are underway to establish powder bed additive manufacturing technologies for Ti-6Al-4V. There are also increasing attempts to use thermal and cold spray to build near-net-shaped parts with buildup rates orders of magnitude higher than powder bed. Thermal spraying, such as HVOF, can oxidize and degrade the alloy due to the high processing temperature. Lowering the flame temperature through inert gas addition in full-size HVOF systems is a possible approach to retain solid-state deposition of the feedstock particles, thereby limiting oxidation and detrimental α-case formation, while providing sufficient heat input for particle softening and plastic deformation at impact. Novel miniaturized HVOF systems, with spray jets of only a few millimeters in width, may further offer the possibility to improve the spatial resolution of the buildup for near-net shape forming. The process parameter range for solid-state deposition of Ti-6A-4V using the liquid-fuelled TAFA Model 825 JPid and the novel hydrogen-fuelled Spraywerx ID-NOVA MK-6 with the addition of nitrogen is shown. Buildups at over 80% deposition efficiency generally yield as-sprayed porosities below 3% and hardness above 200 HV100gf. Attainable microstructures and oxygen content as a function of spray parameters are delineated. Recrystallization and beta-annealing of selected samples lower the residual porosity and can create equiaxed α and intergranular ß-phases. Ultimate tensile strengths of up to 1100 MPa were attained; however, the residual oxygen content of above 0.7% was found to limit β-phase formation, which contributes to a limited elongation to failure.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Advanced materials and composites · Nuclear Materials and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. G. Lutjering and J.C. Williams, Titanium, 2nd ed. Springer, Berlin, 2003.10.1007/978-3-540-71398-2 ↗
2. R.H. Morgan, C.J. Sutcliffe, J. Pattison, M. Murphy, C. Gallagher, A. Papworth, P. Fox, and W. O’Neill, Cold Gas Dynamic Manufacturing—A New Approach to Near-Net Shape Metal Component Fabrication, Mater. Res. Soc. Symp. Proc., 2003, 758, p 73-84.
3. E. Brandl, A. Schoberth, and C. Leyens, Morphology, Microstructure, and Hardness of Titanium (Ti-6Al-4V) Blocks Deposited by Wire-Feed Additive Layer Manufacturing (ALM), Mater. Sci. Eng. A, 2012, 532, p 295-307.10.1016/j.msea.2011.10.095 ↗
4. J. Cizek, O. Kovarik, J. Siegl, K.A. Khor, and I. Dlouhy, Influence of Plasma and Cold Spray deposited Ti Layers on High-Cycle Fatigue Properties of Ti6Al4V Substrates, Surf. Coat. Technol., 2013, 217, p 23–33.10.1016/j.surfcoat.2012.11.067 ↗
5. L.E. Murr, S.A. Quinones, S.M. Gaytan, M.I. Lopez, A. Rodela, E.Y. Martinez, D.H. Hernandez, E. Martinez, F. Medina, and R.B. Wicker, Microstructure and Mechanical Behavior of Ti-6Al-4V Produced by Rapid-Layer Manufacturing, for Biomedical Applications, J. Mech. Behav. Biomed. Mater., 2009, 2(1), p 20-32.10.1016/j.jmbbm.2008.05.004 ↗
6. H.R. Salimijazi, T.W. Coyle, and J. Mostaghimi, Vacuum Plasma Spraying: A New Concept for Manufacturing Ti-6Al-4V Structures, JOM-US, 2006, 58, p 50-56.10.1007/s11837-006-0083-z ↗
7. R.E. Blose, B.H. Walker, R.M. Walker, and S.H. Froes, New Opportunities to Use Cold Spray Process for Applying Additive Features to Titanium Alloys, Met. Powder Rep., 2006, 61, p 30-37.10.1016/S0026-0657(06)70713-5 ↗
8. J.C. Lee, H.J. Kang, W.S. Chu, and S.H. Ahn, Repair of Damaged Mold Surface by Cold-Spray Method, Ann. CIRP, 2007, 56, p 577-580.10.1016/j.cirp.2007.05.138 ↗
9. V.K. Champagne, The Repair of Magnesium Rotorcraft Components by Cold Spray, J. Fail. Anal. Prev., 2008, 8, p 164-175.10.1007/s11668-008-9116-y ↗
10. R. Huang and H. Fukanuma, Study of the Influence of Particle Velocity on Adhesive Strength of Cold Spray Deposits, J. Therm. Spray Technol., 2012, 21(3-4), p 541-549.10.1007/s11666-011-9707-0 ↗
11. W. Wong, E. Irissou, J.G. Legoux, P. Vo, and S. Yue, Powder Processing and Coating Heat Treatment on Cold Sprayed Ti-6Al-4V Alloy, Mater. Sci. Forum., 2012, 706-709, p 258-263.10.4028/www.scientific.net/MSF.706-709.258 ↗
12. P. Vo, E. Irissou, J.-G. Legoux, and S. Yue, Mechanical and Microstructural Characterization of Cold-Sprayed Ti-6Al-4V After Heat Treatment, J. Therm. Spray Technol., 2013, 22(6), p 954-964.10.1007/s11666-013-9945-4 ↗
13. D.L. Gilmore, R.C. Dykhuizen, R.A. Neiser, T.J. Roemer, and M.F. Smith, Particle Velocity and Deposition Efficiency in the Cold Spray Process, J. Therm. Spray Technol., 1999, 8(4), p 576-582.10.1361/105996399770350278 ↗
14. J. Kawakita, H. Katanoda, M. Watanabe, K. Yokoyama, and S. Kuroda, Warm Spraying: An Improved Spray Process to Deposit Novel Coatings, Surf. Coat. Technol., 2008, 202(18), p 4369-4373.10.1016/j.surfcoat.2008.04.011 ↗
15. S. Kuroda, M. Watanabe, K.-H. Kim, and H. Katanoda, Current Status and Future Prospects of Warm Spray Technology, J. Therm. Spray Technol., 2011, 20(4), p 653-676.10.1007/s11666-011-9648-7 ↗
16. S. Kuroda, J. Kawakita, M. Watanabe, and H. Katanoda, Warm Spraying—A Novel Coating Process Based on High-Velocity Impact of Solid Particles, Sci. Technol. Adv. Mater., 2008, 9(3), p 1-17.10.1088/1468-6996/9/3/033002 ↗
17. R.M. Molak, H. Araki, M. Watanabe, H. Katanoda, N. Ohno, and S. Kuroda, Effects of Spray Parameters and Post-spray Heat Treatment on Microstructure and Mechanical Properties of Warm-Sprayed Ti-6Al-4V Coatings, J. Therm. Spray Technol., 2017, 26, p 627-647.10.1007/s11666-016-0494-5 ↗
18. D. MacDonald, R. Fernandez, F. Delloro, and B. Jodoin, Cold Spraying of Armstrong Process Titanium Powder for Additive Manufacturing, J. Therm. Spray Technol., 2017, 26(4), p 598-609.10.1007/s11666-016-0489-2 ↗
19. A. Bhowmik, A.W.Y. Tan, W. Sun, Z. Wei, I. Marinescu, and E. Liu, On the Heat-Treatment Induced Evolution of Residual Stress and Remarkable Enhancement of Adhesion Strength of Cold Sprayed Ti–6Al–4V Coatings, Results Mater., 2020, 7, p 100119. https://doi.org/10.1016/j.rinma.2020.10011910.1016/j.rinma.2020.100119 ↗
20. V.S. Bhattiprolu, K.W. Johnson, and G.A. Crawford, Influence of Powder Microstructure on the Microstructural Evolution of As-Sprayed and Heat Treated Cold-Sprayed Ti-6Al-4V Coatings, J. Therm. Spray Technol., 2019, 28, p 174-188. https://doi.org/10.1007/s11666-018-0812-110.1007/s11666-018-0812-1 ↗
21. V.N.V. Munagal, V. Akinyi, P. Vo, and R.R. Chromik, Influence of Powder Morphology and microstructure on the Cold Spray and Mechanical Properties of Ti6Al4V Coatings, J. Therm. Spray Technol., 2018, 27, p 827-842.10.1007/s11666-018-0729-8 ↗
22. R.M. Molak, H. Araki, M. Watanabe, H. Katanoda, N. Ohno, and S. Kuroda, Warm Spray Forming of Ti-6Al-4V, J. Therm. Spray Technol., 2014, 23(1-2), p 197-212.10.1007/s11666-013-0024-7 ↗
23. P. Khamsepour, J. Oberste-Berghaus, M. Aghasibeig, F. Ben Ettouil, C. Moreau, and A. Dolatabadi, The Effect of Spraying Parameters of the Inner-Diameter High-Velocity Air-Fuel (ID-HVAF) Torch on Characteristics of Ti-6Al-4V In-Flight Particles and Coatings Formed at Short Spraying Distances, J. Therm. Spray Technol., 2022, 18, p 164.
24. Standard Test Methods for Tension Testing of Metallic Materials, ASTM E8/E8M-22, ASTM International, West Conshohocken, 2022.