journal article·2019-12

Influence of Introducing an Organic Pore-Forming Agent on the Porosity and Microstructure of Alumina Coatings Produced by the Atmospheric Plasma Spray Process

W. Tillmann, O. Khalil, M. Abdulgader

Publisher page

Abstract

Controlling the amount of porosity that can be added to ceramic coatings produced by means of atmospheric plasma spraying has always been a challenging task, especially, when coatings are produced with high adhesion/cohesion strengths combined with higher deposition efficiency. However, coating porosity can be varied in a limited fashion between 2 and 25% by changing the process parameters. The use of pore-forming agent is, therefore, an adequate alternative to add porosity by using the optimal spraying parameters. In this work, baking flour was vertically inserted into the plasma plume at different positions and with different feed rates while depositing alumina particles, as the basic feedstock powder, using optimized spray parameters. According to the spray conditions used in this work, flour particles have successfully contributed to the obtained coating porosity; however, the effectiveness is higher when flour is inserted at about half of the spray distance and depends on the feed rate of the flour. In comparison with flour-free alumina coatings, the porosity of flour-alumina’s coatings increased by approx. 50 area% and 170 area% when the flour’s weight fraction was equal 10 and 20 wt.% of the feedstock powder, respectively. Adhesion/cohesion strengths, hardness and thickness of coatings were strongly affected.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Advanced ceramic materials synthesis · Material Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. N. Curry, Design of TBCs, Ph.D. Thesis, University West, 2014, p. 3
2. P. Ctibor, R. Lechnerova, and V. Benes, Quantitative Analysis of Pores of Two Types in a Plasma-Sprayed Coating, Mater. Charact., 2006, 56, p 297-30410.1016/j.matchar.2005.11.016 ↗
3. H. Xie, Y.C. Xie, G.J. Yang, C.X. Li, and C.J. Li, Modeling Thermal Conductivity of Thermally Sprayed Coatings with Intrasplat Cracks, J. Therm. Spray Technol., 2013, 22(8), p 1328-133610.1007/s11666-013-0005-x ↗
4. I.O. Golosnoy, A. Cipitria, and T.W. Clyne, Heat Transfer Through Plasma-Sprayed Thermal Barrier Coatings in Gas Turbines: A Review of Recent Work, J. Therm. Spray Technol., 2009, 18(5–6), p 809-82110.1007/s11666-009-9337-y ↗
5. Y. Tan, A. Shyam, W.B. Choi, E. Lara-Curzio, and S. Sampath, Anisotropic Elastic Properties of Thermal Spray Coatings Determined via Resonant Ultrasound Spectroscopy, Acta Mater., 2010, 58(16), p 5305-531510.1016/j.actamat.2010.06.003 ↗
6. G.R. Li, B.W. Lv, G.J. Yang, W.X. Zhang, C.X. Li, and C.J. Li, Relationship Between Lamellar Structure and Elastic Modulus of Thermally Sprayed Thermal Barrier Coatings with Intra-Splat Cracks, J. Therm. Spray Technol., 2015, 24(8), p 1355-136710.1007/s11666-015-0292-5 ↗
7. C.G. Levi, Emerging Materials and Processes for Thermal Barrier Systems, Curr. Opin. Solid State Mater. Sci., 2004, 8, p 77-9110.1016/j.cossms.2004.03.009 ↗
8. R. Miller, Thermal Barrier Coatings for Aircraft Engines: History and Directions, J. Therm. Spray Technol., 1997, 6(1), p 35-4210.1007/BF02646310 ↗
9. W.W. Zhang, G.R. Li, Zhang et al., Multiscale Pores in TBCs for Lower Thermal Conductivity, J. Therm. Spray Technol., 2017, 26, p 1183-119710.1007/s11666-017-0585-y ↗
10. W.W. Zhang, G.R. Li, Q. Zhang, G. Yang, G.W. Zhang, and H.M. Mu, Self-enhancing Thermal Insulation Performance of Bimodal-Structured Thermal Barrier Coating, J. Therm. Spray Technol., 2018, 27, p 1064-107510.1007/s11666-018-0754-7 ↗
11. G. Li and G. Yang, Corrigendum to Understanding of Degradation-Resistant Behavior of Nanostructured Thermal Barrier Coatings with Bimodal Structure, J. Mater. Sci. Technol., 2019, 35, p 231-23810.1016/j.jmst.2018.09.054 ↗
12. J.R. Brandon and R. Taylor, Phase Stability of Zirconia-Based Thermal Barrier Coatings Part I. Zirconia-yttria alloys, Surf. Coat. Technol., 1991, 46(1), p 75-9010.1016/0257-8972(91)90151-L ↗
13. P. Ramaswamy, S. Seetharamu, K.B.R. Varma, and K.J. Rao, Evaluation of CaO-CeO2-Partially Stabilized Zirconia Thermal Barrier Coatings, Ceram. Int., 1999, 25, p 317-32410.1016/S0272-8842(98)00041-8 ↗
14. R.C. Reed, The Super Alloys, Fundamentals and Applications, Cambridge University Press, Cambridge, 200610.1017/CBO9780511541285 ↗
15. D. Thirumalaikumarasamy, K. Shanmugam, and V. Balasubramanian, Influences of Atmospheric Plasma Spraying Parameters on the Porosity Level of Alumina Coating on AZ31B Magnesium Alloy Using Response Surface Methodology, Mater. Int., 2012, 22(5), p 468-479
16. A. Sanson, P. Pinasco, and E. Roncari, Influence of Pore Formers on Slurry Composition and Microstructure of Tape Cast Supporting Anodes for SOFCs, J. Eur. Ceram. Soc., 2008, 28(6), p 1221-122610.1016/j.jeurceramsoc.2007.10.001 ↗
17. H. Jamali, R. Mozafarinia, R.S. Razavi, R. Ahmadi-pidani, and M.R. Loghman-Estarki, Fabrication and Evaluation of Plasma-Sprayed Nanostructured and Conventional YSZ Thermal Barrier Coatings, Curr. Nanosci., 2012, 8, p 402-40910.2174/157341312800620250 ↗
18. O.C. Kwon, C. Lee, S.Y. Hwang, Microstructure Control of NiO(graphite)/8YSZ SOFC Anode Coatings by APS, in Conference Proceedings ITSC, 200710.31399/asm.cp.itsc2007p0750 ↗
19. R.M.C. Clemmer and S.F. Corbin, The Influence of Pore and Ni Morphology on the Electrical Morphology of Porous Ni/YSZ Composite Anodes for Use in Solid Oxide Fuel Cells, Solid State Ion., 2009, 180(9–10), p 721-73010.1016/j.ssi.2009.02.030 ↗
20. R.M.C. Clemmer and S.F. Corbin, Effect of Graphite Pore-Forming Agents on the Sintering Characteristics of Ni/YSZ Composites for Solid Oxide Fuel Cell Applications, Int. J. Appl. Ceram. Technol., 2012, 9(6), p 1022-103410.1111/j.1744-7402.2011.02639.x ↗
21. B.A. Horri, C. Selomulya, and H. Wang, Electrochemical Characteristics and Performance of Anode-Supported SOFCs Fabricated Using Carbon Microspheres as a Pore-Former, Int. J. Hydrog. Energy, 2012, 37, p 15311-1531910.1016/j.ijhydene.2012.07.108 ↗
22. F. Heshmatpour and R.B. Aghakhanpour, Synthesis and Characterization of Nanocrystalline Zirconia Powder by Simple Sol–Gel Method with Glucose and Fructose as Organic Additives, Powder Technol., 2011, 205(1–3), p 193-20010.1016/j.powtec.2010.09.011 ↗
23. L. Tai and P.A. Lessing, Plasma Spraying of Porous Electrodes for a Planar Solid Oxide Fuel Cell, J. Am. Ceram. Soc., 1991, 74(3), p 501-50410.1111/j.1151-2916.1991.tb04050.x ↗
24. H. Weckmann, A. Syed, Z. Ilhan, and J. Arnold, Development of Porous Anode Layers for the Solid Oxide Fuel Cell by Plasma Spraying, J. Therm. Spray Technol., 2006, 15(4), p 604-60910.1361/105996306X147289 ↗
25. M. Poon and O. Kesler, The Influence of Pore Formers on the Microstructure of Plasma-Sprayed NiO-YSZ Anodes, J. Power Sour., 2012, 210, p 204-21710.1016/j.jpowsour.2012.02.046 ↗
26. G. Kaletunc, K.J. Breslauer, Characterization of Cereals and Flours: Properties, Analysis and Applications, Ohio & Rutgers University, 200310.1201/9780203911785 ↗
27. K.J. Zeleznak and R.C. Hoseney, The Glass Transition in Starch, Cereal Chem., 1987, 64, p 121-124
28. P. Aggarwal, D. Dollimore, and K. Heon, Comparative Thermal Analysis Study of Two Biopolymers, Starch and Cellulose, J. Therm. Anal., 1997, 50(1–2), p 7-1710.1007/BF01979545 ↗
29. M. Mellali, Influence of Roughness and Substrate Surface Temperature on the Adhesion/Cohesion and on the Residual Stresses of Alumina Coatings Plasma Sprayed, Ph.D. Thesis, University of Limoges, 1994
30. L. Bianchi, F. Blein, P. Lucchese, A. Grimaud, and P. Fauchais, Comparison of Plasma Sprayed Alumina and Zirconia Coatings by RF and DC Plasma Spraying, J. Therm. Spray Technol., 1995, 4(1), p 59-6610.1007/BF02648529 ↗
31. M. Vardelle, A. Vardelle, A.C. Leger, D. Gobin, and P. Fauchais, Influence of the Particle Parameters at Impact on Splat Formation and Solidification in Plasma Spraying Processes, J. Therm. Spray Technol., 1995, 4(1), p 50-5810.1007/BF02648528 ↗
32. S. Kuroda and T.W. Clyne, The Quenching Stress in Thermally Sprayed Coatings, Thin Solid Films, 1991, 200(1), p 49-6610.1016/0040-6090(91)90029-W ↗
33. G.J. Yang, C.J. Li, C.X. Li, K. Kondoh, and A. Ohmori, Improvement of Adhesion and Cohesion in Plasma-Sprayed Ceramic Coatings by Heterogeneous Modification of Nonbonded Lamellar Interface Using High Strength Adhesive Infiltration, J. Therm. Spray Technol., 2013, 22, p 36-4710.1007/s11666-012-9831-5 ↗
34. R. Venkataraman, G. Dasa, S.R. Singh, L.C. Pathak, R.N. Ghosha, B. Venkataraman et al., Study on Influence of Porosity, Pore Size, Spatial and Topological Distribution of Pores on Microhardness of as Plasma Sprayed Ceramic Coatings. Mater. Sci. Eng. A, 2007, 269–274, p 445–446