Surface and Cross-Sectional Micro-scratch Characterization of Cold-Sprayed SS316L Coatings
Source abstract
Abstract
Abstract This study presents a scratch test-based framework for evaluating interfacial adhesion, inter-splat cohesion, and fracture toughness of cold-sprayed SS316L coatings on SS304 substrates, representing the first such application for this coating system. To systematically investigate the influence of process parameters on microstructure and mechanical performance, coatings were deposited at four traverse speeds (20, 100, 250, and 400 mm/s). Among these, the coating produced at 250 mm/s demonstrated the lowest porosity (0.14%) compared to porosities of 0.2, 2.04, and 2.04% at 20, 100, and 400 mm/s, respectively. Notably, this coating also achieved the highest fracture toughness (28 ± 4 MPa-m0.5, as determined by Zhang’s model), closely approaching the bulk SS316L value (34 MPa-m0.5). Superior inter-splat cohesion was evidenced by the smallest projected cone area (0.12 mm2) at the scratch indenter tip, with no splat debonding or cracks observed under progressive loading. Furthermore, exceptional interfacial adhesion was demonstrated, as coatings deposited at 250 and 400 mm/s exhibited no interface failure even at maximum applied loads (50 N). These findings establish scratch testing as a reliable quantitative tool for assessing fracture toughness in cold-sprayed coatings. Additionally, an intermediate traverse speed is identified as optimal for achieving the best combination of fracture toughness, inter-splat cohesion, and interfacial adhesion.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Metal Alloys Wear and Properties · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. T. Schmidt, F. Gärtner, H. Assadi, and H. Kreye, Development of a Generalized Parameter Window for Cold Spray Deposition, Acta Mater., 2006, 54, p 729–742. https://doi.org/10.1016/j.actamat.2005.10.00510.1016/j.actamat.2005.10.005 ↗
2. H. Assadi, F. Gärtner, T. Stoltenhoff, and H. Kreye, Bonding Mechanism in Cold Gas Spraying, Acta Mater., 2003, 51, p 4379–4394. https://doi.org/10.1016/S1359-6454(03)00274-X10.1016/S1359-6454(03)00274-X ↗
3. H. Assadi, F. Gärtner, T. Klassen, and H. Kreye, Comment on ‘Adiabatic Shear Instability is Not Necessary for Adhesion in Cold Spray,’ Scr. Mater., 2019, 162, p 512–514. https://doi.org/10.1016/j.scriptamat.2018.10.03610.1016/j.scriptamat.2018.10.036 ↗
4. T. Schmidt, H. Assadi, F. Gärtner, H. Richter, T. Stoltenhoff, H. Kreye et al., From Particle Acceleration to Impact and Bonding in Cold Spraying, J. Therm. Spray Technol., 2009, 18, p 794–808. https://doi.org/10.1007/s11666-009-9357-710.1007/s11666-009-9357-7 ↗
5. A. Kumar, S. Rathor, M. Vostrak, S. Houdkova, R. Kant, and H. Singh, Exploring Potential of Cold Spray Technology for Medical Devices: Current and Future Scenario, Mater. Today Commun., 2024 https://doi.org/10.1016/j.mtcomm.2024.10953410.1016/j.mtcomm.2024.109534 ↗
6. M. Hassani-Gangaraj, D. Veysset, V.K. Champagne, K.A. Nelson, and C.A. Schuh, Adiabatic Shear Instability is Not Necessary for Adhesion in Cold Spray, Acta Mater., 2018, 158, p 430–439. https://doi.org/10.1016/j.actamat.2018.07.06510.1016/j.actamat.2018.07.065 ↗
7. A. Kumar, H. Singh, and R. Kant, Influence of Substrate Roughness and Ceramic Content on Deposition Characteristics of Cold-Sprayed Ti/TiO2 Deposits, Met. Mater. Int., 2022 https://doi.org/10.1007/s12540-022-01323-410.1007/s12540-022-01323-4 ↗
8. Z. Zhang, Z. Liu, B. Wang, and Y. Cai, Effect of Plastic Deformation of Particle and Substrate on Metallurgical Bonding During Cold Spraying, Mater. Lett., 2024, 373, p 137157. https://doi.org/10.1016/j.matlet.2024.13715710.1016/j.matlet.2024.137157 ↗
9. B. Dikici and M. Topuz, Production of Annealed Cold-Sprayed 316L Stainless Steel Coatings for Biomedical Applications and Their In-Vitro Corrosion Response, Prot. Met. Phys. Chem. Surf., 2018, 54(2), p 333–339.10.1134/S2070205118020168 ↗
10. X. Jiang, N. Overman, C. Smith, and K. Ross, Microstructure, Hardness and Cavitation Erosion Resistance of Different Cold Spray Coatings on Stainless Steel 316 for Hydropower Applications, Mater. Today Commun., 2020, 25, p 101305. https://doi.org/10.1016/j.mtcomm.2020.10130510.1016/j.mtcomm.2020.101305 ↗
11. S. Yin, X. Yan, R. Jenkins et al., Hybrid Additive Manufacture of 316L Stainless Steel with Cold Spray and Selective Laser Melting: Microstructure and Mechanical Properties, J. Mater. Process. Tech., 2019 https://doi.org/10.1016/j.jmatprotec.2019.05.02910.1016/j.jmatprotec.2019.05.029 ↗
12. S. Yin, J. Cizek, X. Yan, and R. Lupoi, Annealing Strategies for Enhancing Mechanical Properties of Manufactured 316L Stainless Steel Deposited by Cold Spray, Surf. Coat. Technol., 2019, 370, p 353–361. https://doi.org/10.1016/j.surfcoat.2019.04.01210.1016/j.surfcoat.2019.04.012 ↗
13. J. Huang, W. Ma, Y. Xie, H. Fukanum, K. Zhang, G. Wang, and R. Huang, Influence of Cold Gas Spray Processing Conditions on the Properties of 316L Stainless Steel Coatings, Surf. Eng., 2019, 35(9), p 784–791. https://doi.org/10.1080/02670844.2019.158496710.1080/02670844.2019.1584967 ↗
14. J. Lee, S. Shin, H. Kim, and C. Lee, Effect of Gas Temperature on the Critical Velocity and Characteristics in Kinetic Spraying, Appl. Surf. Sci., 2007, 253, p 3512–3520. https://doi.org/10.1016/j.apsusc.2006.07.06110.1016/j.apsusc.2006.07.061 ↗
15. Y. Xie, S. Yin, and C. Chen, New Insights into the Coating/Substrate Interfacial Bonding Mechanism in Cold Spray, Scripta Mater., 2016, 125, p 2351–2363. https://doi.org/10.1016/j.scriptamat.2016.07.02410.1016/j.scriptamat.2016.07.024 ↗
16. F.R. Vaz, V. Luzin, F. Salvemini et al., The Effect of the Deposition Strategy and Heat Treatment on Cold Spray Additive Manufactured 316L Stainless Steel, Adv. Eng. Mater., 2024, 26(14), p 1. https://doi.org/10.1002/adem.20230215610.1002/adem.202302156 ↗
17. R. Cortes, A.M. Garrido-Manerio, and P. Poza, Erosion Behaviour of Cold Sprayed Stainless-Steel Coatings for Civil Infrastructures: An Energetic Approach, Results Eng., 2024, 22, p 102166. https://doi.org/10.1016/j.rineng.2024.10216610.1016/j.rineng.2024.102166 ↗
18. Standard Test Method for Adhesion or Cohesion Strength of Thermal Spray Coatings 1 n.d. https://doi.org/10.1520/C0633-13R17.10.1520/C0633-13R17 ↗
19. M.S. Younger, K.H. Eckelmeyer, Overcoming Residual Stresses and Machining Distortion in the Production of Aluminum Alloy Satellite Boxes. Sandia Report, 2007.10.2172/922073 ↗
20. A. Fardan, C.C. Berndt, and R. Ahmed, Numerical Modelling of Particle Impact and Residual Stresses in Cold Sprayed Coatings: A Review, Surf. Coat Technol., 2021 https://doi.org/10.1016/j.surfcoat.2021.12683510.1016/j.surfcoat.2021.126835 ↗
21. B.C. White, W.A. Story, L.N. Brewer, and J.B. Jordon, Fracture Mechanics Methods for Evaluating the Adhesion of Cold Spray Deposits, Eng. Fract. Mech., 2019, 205, p 57–69. https://doi.org/10.1016/j.engfracmech.2018.11.00910.1016/j.engfracmech.2018.11.009 ↗
22. S.T. Method, Standard Test Method for Adhesion or Cohesion Strength of Thermal Spray Coatings 1, Current, 2001, 03, p 1–7. https://doi.org/10.1520/C0633-13R17.110.1520/C0633-13R17.1 ↗
23. D. Boruah, B. Robinson, T. London, H. Wu, H. de Villiers-Lovelock, P. McNutt et al., Experimental Evaluation of Interfacial Adhesion Strength of Cold Sprayed Ti-6Al-4V Thick Coatings Using an Adhesive-Free Test Method, Surf. Coat. Technol., 2020 https://doi.org/10.1016/j.surfcoat.2019.12513010.1016/j.surfcoat.2019.125130 ↗
24. G. Quinn, Fracture Toughness of Ceramics by the Vickers Indentation Crack Length Method: A Critical Review.
25. S. Nakonechnyi, T. Soloviova, A. Yurkova, I. Solodkiy, and P. Loboda, Cold Sprayed AlNiCoFeCr-TiB2 Metal Matrix Composite Coatings, Vacuum, 2023 https://doi.org/10.1016/j.vacuum.2023.11214410.1016/j.vacuum.2023.112144 ↗
26. J. Nohava, B. Bonferroni, G. Bolelli, and L. Lusvarghi, Interesting Aspects of Indentation and Scratch Methods for Characterization of Thermally-Sprayed Coatings, Surf. Coat. Technol., 2010, 205, p 1127–1131. https://doi.org/10.1016/j.surfcoat.2010.08.08610.1016/j.surfcoat.2010.08.086 ↗
27. E. Lopez and F. Beltzung, Measurement of Cohesion and Adhesion Strengths in Alumina Coatings Produced by Plasma Spraying, J. Mater. Sci. Lett., 1989, 8(3), p 346–348.10.1007/BF00725519 ↗
28. M.M. Harfouche, S.A. Alidokht, A. Islas Encalada, V.N.V. Mungala, R.R. Chromik, C. Moreau et al., Scratch Adhesion Testing of Thick HVOF Thermal Sprayed Coatings, J. Therm. Spray Technol., 2024, 33, p 1158–1166. https://doi.org/10.1007/s11666-024-01741-310.1007/s11666-024-01741-3 ↗
29. A.-T. Akono, Scratch Tests: A New Way of Evaluating the Fracture Toughness of Materials Department of Civil and Environmental Engieering. 2009.
30. A.T. Akono, and F.J. Ulm, Scratch Test Model for the Determination of Fracture Toughness, Eng. Fract. Mech., 2011, 78, p 334–342. https://doi.org/10.1016/j.engfracmech.2010.09.01710.1016/j.engfracmech.2010.09.017 ↗
31. A.T. Akono, and F.J. Ulm, An Improved Technique for Characterizing the Fracture Toughness via Scratch Test Experiments, Wear, 2014, 313, p 117–124. https://doi.org/10.1016/j.wear.2014.02.01510.1016/j.wear.2014.02.015 ↗
32. J. Zhang, C. Zhang, Y. Li, M. Zhao, and B. Wang, Fracture Toughness Testing of Metallic Materials Based on Scratch Tests, Theor. Appl. Fract. Mech., 2024 https://doi.org/10.1016/j.tafmec.2024.10439310.1016/j.tafmec.2024.104393 ↗
33. Thermal spraying-Evaluation of adhesion/cohesion of thermal sprayed ceramic coatings by transverse scratch testing ISO 27307:2015(E) ii COPYRIGHT PROTECTED DOCUMENT ISO 27307:2015(E). 2015.
34. A.W.Y. Tan, W. Sun, Y.P. Phang, M. Dai, I. Marinescu, Z. Dong et al., Effects of Traverse Scanning Speed of Spray Nozzle on the Microstructure and Mechanical Properties of Cold-Sprayed Ti6Al4V Coatings, J. Therm. Spray Technol., 2017, 26, p 1484–1497. https://doi.org/10.1007/s11666-017-0619-510.1007/s11666-017-0619-5 ↗
35. W. Wong, A. Rezaeian, E. Irissou, J. Legoux, and S. Yue, Cold Spray Characteristics of Commercially Pure Ti and Ti-6Al-4V, Advanced Materials Research, 2010, 89–91, p 639–644. https://doi.org/10.4028/www.scientific.net/AMR.89-91.63910.4028/www.scientific.net/AMR.89-91.639 ↗
36. A. Kumar, H. Singh, and R. Kant, Microstructural and Tribological Properties of Laser-Treated Cold-Sprayed Titanium/Baghdadite Deposits, J. Mater. Res., 2022, 37, p 2698–2709. https://doi.org/10.1557/s43578-022-00675-210.1557/s43578-022-00675-2 ↗
37. T.S. Senthil, S.R. Babu, and M. Puviyarasan, Mechanical, Microstructural and Fracture Studies on Inconel 825–SS316L Functionally Graded Wall Fabricated by Wire Arc Additive Manufacturing, Sci. Rep., 2023, 13, p 5321. https://doi.org/10.1038/s41598-023-32124-310.1038/s41598-023-32124-3 ↗
38. V.N.V. Munagala, S. Bessette, R. Gauvin, and R.R. Chromik, Sliding Wear of Cold Sprayed Ti6Al4V Coatings: Effect of Porosity and Normal Load, Wear, 2020 https://doi.org/10.1016/j.wear.2020.20326810.1016/j.wear.2020.203268 ↗