journal article·2012-12Open access

Adhesion of Ceramic Coating on Thin and Smooth Metal Substrate: A Novel Approach with a Nanostructured Ceramic Interlayer

R. Vert, P. Carles, E. Laborde, G. Mariaux, E. Meillot, A. Vardelle

Abstract

Abstract The adhesion of plasma-sprayed coating is to a large extent controlled by the cleanness and roughness of the surface on which the coating is deposited. So, most of the plasma spray procedures involve surface pretreatment by grit-blasting to adapt the roughness of the surface to the size of the impacting particles. This preparation process brings about compressive stresses that make it inappropriate for thin substrates. The present works aims to elaborate a ceramic coating on a thin metal substrate with a smooth surface. The coating system is intended for use in a generation–IV nuclear energy system. It must exhibit a good adhesion between the ceramic topcoat (about 0.5-mm thick) and the smooth metal substrate (1-mm thick) to meet the specifications of the application. Our approach has consisted in depositing the ceramic layer on a few micrometers thick ceramic layer made by suspension spraying. We have observed the interface between both ceramic layers by transmission electronic microscope and studied the adhesion of the nanostructured layer by the Vickers Indentation Cracking technique and that of the coating system by tensile test.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Nuclear Materials and Properties · Fusion materials and technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (17)

Show source-provided references
1. A Technology Roadmap for Generation IV Nuclear Energy Systems, US DOE Nuclear Energy Research Advisory Committee and the Generation IV International Forum, December 2002
2. R. Stainsby et al, Gas Cooled Fast Reactor Research and Development in the European Union, Sci. Technol. Nucl. Install. 2009, 2009, Article ID 23862410.1155/2009/238624 ↗
3. H. Liao, P. Vaslin, Y. Yang, and C. Coddet, Determination of Residual Stress Distribution from In Situ Curvature Measurements for Thermally Sprayed WC-Co Coatings, J. Therm. Spray Technol., 1997, 6(2), p 235-24110.1007/s11666-997-0018-4 ↗
4. O. Racek, C.C. Berndt, D.N. Guru, and J. Heberlein, Nanostructured and Conventional YSZ Coatings Deposited Using APS and TTPR Techniques, Surf. and Coat. Tech., 2006, 201, p 338-34610.1016/j.surfcoat.2005.11.122 ↗
5. R. Vert, C. Dublanche-Tixier, D. Chicot, E. Meillot, A. Vardelle, and G. Mariaux, Adhesion of YSZ Plasma Sprayed Coating on Low Roughness and Thin Substrates, Surf. and Coat. Tech., 2010, 205(4), p 999-100310.1016/j.surfcoat.2010.07.090 ↗
6. E. Meillot, R. Vert, C. Caruyer, D. Damiani, and M. Vardelle, Manufacturing Nanostructured YSZ Coatings by Suspension Plasma Spraying (SPS): Effect of Injection Parameters, J. Phys. D, 2011, 44, 194008, 8 pp10.1088/0022-3727/44/19/194008 ↗
7. S.H. Leigh and C.C. Berndt, A Test for Coating Adhesion on Flat Substrates—A Technical Note, J. Therm. Spray Technol., 1994, 3(2), p 184-19010.1007/BF02648276 ↗
8. R. Vert, X. Decoopman, I.C. Gruescu, E. Meillot, D. Chicot, A. Vardelle, and G. Mariaux, Adhesive and Cohesive Properties of Nanostructured ZrO2 Coatings by Vickers Indentation Cracking Technique, Thin Solid Film, 2011, 519, p 7789-779510.1016/j.tsf.2011.04.228 ↗
9. V. Debout, Ph.D. Thesis, in French, 2007, Limoges, University of Limoges, 285 pp, 2007. http://epublications.unilim.fr/theses/2007/debout-vincent/debout-vincent.pdf
10. A. Bacciochini, J. Ilavsy, G. Montavon, A. Denoirjean, F. Ben-Ettouil, S. Valette, P. Fauchais, and K. Wittmann-Teneze, Quantification of Void Networks Architectures of Suspension Plasma Sprayed (SPS) Yttria Stabilized Zirconia (YSZ) Coatings Using Ultra-Small-Angle X-Ray Scattering (USAXS), Mater. Sci. Eng., A, 2010, 528, p 92-10210.1016/j.msea.2010.06.082 ↗
11. M.C. Biesinger, B.P. Payne, A.P. Grosvenor, L.W.M. Lau, A.R. Gerson, and R.St.C. Smart, Resolving Surface Chemical States in XPS Analysis of First Row Transition Metals, Oxides and Hydroxides: Cr, Mn, Fe, Co and Ni, Appl. Surf. Sci., 2011, 257(7), p 2717-273010.1016/j.apsusc.2010.10.051 ↗
12. S. Colin, E. Beche, R. Berjoan, H. Jolibois, and A. Chambaudet, An XPS and AES Study of the Free Corrosion of Cu-, Ni- and Zn-Based Alloys in Synthetic Sweat, Corr. Sci., 1999, 41, p 1051-106510.1016/S0010-938X(98)00141-3 ↗
13. S. Goutier, M. Vardelle, and P. Fauchais, Last Developments in Diagnostics to Follow Splats Formation During Plasma Spraying, J. Phys: Conf. Ser., 2011, 275, p 01200310.1088/1742-6596/275/1/012003 ↗
14. M.C. Munoz, S. Gallego, J.I. Beltran, and J. Cerda, Adhesion at Metal-ZrO2 Interfaces, Surf. Sci. Rep., 2006, 61, p 303-34410.1016/j.surfrep.2006.03.002 ↗
15. T. Chraska and A.H. King, Transmission Electron Microscopy Study of Rapid Solidification of Plasma Sprayed Zirconia, Thin Solid Films, 2001, 397, p 40-4810.1016/S0040-6090(01)01361-X ↗
16. C. Delbos, J. Fazilleau, V. Rat, J.-F. Coudert, and P. Fauchais, Phenomena Involved in Suspension Plasma Spraying, PCPP, 2006, 26, p 393-414
17. C.R.C. Lima and J.M. Guilemany, Adhesion Improvement of Thermal Barrier Coatings with HVOF Thermally Sprayed Bond Coats, Surf. Coat. Technol., 2007, 201(8), p 4694-470110.1016/j.surfcoat.2006.10.005 ↗