Microstructure and Properties of Cu Coating Fabricated onto Diamond-Cu Substrate by Low-Temperature HVOF Process
Source abstract
Abstract
Diamond-Cu composites have been considered to be the next generation of electronic packing materials. One of the key stumbles for such an application is the joining problem between diamond-Cu composites and other materials due to the poor wettability of the diamond particles in the composites. In order to overcome this hurdle, pure Cu powder was thermally sprayed onto diamond-Cu substrate by low-temperature high-velocity oxygen fuel spraying process. Microstructure and some fundamental properties of the coating obtained were systematically investigated, and morphologies of the single splat deposited on the diamond-Cu substrate were also observed. The splats obtained have good adhesion with the substrate as fine particles flattened sufficiently, while the coarse particles were significantly deformed. The coating was quite dense with porosity lower than 1%, oxygen content under 0.5% and thermal conductivity about 266 Wm−1 K−1 and still remained on the diamond-Cu substrate after 50 thermal shock cycles between 300 °C and water bath at room temperature. Meanwhile, the solderability of the coating was significantly improved. Therefore, Cu coating deposited on diamond-Cu substrate by low-temperature high-velocity oxygen fuel spraying process can be beneficial in electronic industry assisting with soldering and improved wettability for joining of other materials.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · Diamond and Carbon-based Materials Research · High-Temperature Coating Behaviors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (43)
Show source-provided references
1. C. Zhao and J. Wang, Enhanced Mechanical Properties in Diamond/Cu Composites with Chromium Carbide Coating for Structural Applications, Mater. Sci. Eng. A, 2013, 588, p 221-22710.1016/j.msea.2013.09.034 ↗
2. C. Zhang, R. Wang, Z. Cai, C. Peng, Y. Feng, and L. Zhang, Effects of Dual-Layer Coatings on Microstructure and Thermal Conductivity of Diamond/Cu Composites Prepared by Vacuum Hot Pressing, Surf. Coat. Technol., 2015, 277, p 299-30710.1016/j.surfcoat.2015.07.059 ↗
3. J. Li, H. Zhang, Y. Zhang, Z. Che, and X. Wang, Microstructure and Thermal Conductivity of Cu/Diamond Composites with Ti-Coated Diamond Particles Produced by Gas Pressure Infiltration, J. Alloys Compd., 2015, 647, p 941-94610.1016/j.jallcom.2015.06.062 ↗
4. Th Schubert, B. Trindade, T. Weißgärber, and B. Kieback, Interfacial Design of Cu Based Composites Prepared by Powder Metallurgy for Heat Sink Applications, Mater. Sci. Eng. A, 2008, 475(1-2), p 39-4410.1016/j.msea.2006.12.146 ↗
5. T. Schubert, Ł. Ciupiński, W. Zieliński, A. Michalski, T. Weißgärber, and B. Kieback, Interfacial Characterization of Cu/Diamond Composites Prepared by Powder Metallurgy for Heat Sink Applications, Scr. Mater., 2008, 58(4), p 263-26610.1016/j.scriptamat.2007.10.011 ↗
6. M. Zain-ul-abdein, K. Raza, F.A. Khalid, and T. Mabrouki, Numerical Investigation of the Effect of Interfacial Thermal Resistance Upon the Thermal Conductivity of Copper/Diamond Composites, Mater. Des., 2015, 86, p 248-25810.1016/j.matdes.2015.07.059 ↗
7. S. Ren, X. Shen, C. Guo, N. Liu, J. Zang, X. He, and X. Qu, Effect of Coating on the Microstructure and Thermal Conductivities of Diamond-Cu Composites Prepared by Powder Metallurgy, Compos. Sci. Technol., 2011, 71, p 1550-155510.1016/j.compscitech.2011.06.012 ↗
8. H. Bai, N. Ma, J. Lang, and C. Zhu, Effect of a New Pretreatment on the Microstructure and Thermal Conductivity of Cu/Diamond Composites, J. Alloys Compd., 2013, 580, p 382-38510.1016/j.jallcom.2013.06.027 ↗
9. X.Y. Shen, X.B. He, S.B. Ren, H.M. Zhang, and X.H. Qu, Effect of Molybdenum as Interfacial Element on the Thermal Conductivity of Diamond/Cu Composites, J. Alloys Compd., 2012, 529, p 134-13910.1016/j.jallcom.2012.03.045 ↗
10. J. Flaquer, A. Ríos, A. Martín-Meizoso, S. Nogales, and H. Böhm, Effect of Diamond Shapes and Associated Thermal Boundary Resistance on Thermal Conductivity of Diamond-Based Composites, Comp. Mater. Sci., 2007, 41(2), p 156-16310.1016/j.commatsci.2007.03.016 ↗
11. A. Abyzov, S. Kidalov, and F. Shakhov, High Thermal Conductivity Compositess Consisting of Diamond Filler with Tungsten Coating and Copper (Silver) Matrix, J. Mater. Sci., 2011, 46, p 1424-143810.1007/s10853-010-4938-x ↗
12. E.A. Ekimov, N.V. Suetin, A.F. Popovich, and V.G. Ralchenko, Thermal Conductivity of Diamond Compositess Sintered Under High Pressures, Diam. Relat. Mater., 2008, 17, p 838-84310.1016/j.diamond.2007.12.051 ↗
13. Y. Dong, R. Zhang, X. He, Z. Ye, and X. Qu, Fabrication and Infiltration Kinetics Analysis of Ti-Coated Diamond/Copper Compositess with Near-Net-Shape by Pressureless Infiltration, Mater. Sci. Eng. B, 2012, 177, p 1524-153010.1016/j.mseb.2012.08.009 ↗
14. J.M. Molina, M. Rheme, J. Carron, and L. Weber, Thermal Conductivity of Aluminum Matrix Composites Reinforced with Mixtures of Diamond and SiC Particles, Scr. Mater., 2008, 58, p 393-39610.1016/j.scriptamat.2007.10.020 ↗
15. G. Chen, W. Yang, R. Dong, M. Hussain, and G. Wu, Interfacial Microstructure and Its Effect on Thermal Conductivity of SiCp/Cu Composites, Mater. Des., 2014, 63, p 109-11410.1016/j.matdes.2014.05.068 ↗
16. I.E. Monje, E. Louis, and J.M. Molina, Optimizing Thermal Conductivity in Gas-Pressure Infiltrated Aluminum/Diamond Composites by Precise Processing Control, Compos. Part A, 2013, 48, p 9-1410.1016/j.compositesa.2012.12.010 ↗
17. Z. Tan, Z. Li, G. Fan, X. Kai, G. Ji, L. Zhang, and D. Zhang, Diamond/Aluminum Composites Processed by Vacuum Hot Pressing: Microstructure Characteristics and thermal Properties, Diam. Relat. Mater., 2013, 31, p 1-510.1016/j.diamond.2012.10.008 ↗
18. L. Weber and R. Tavangar, On the Influence of Active Element Content on the Thermal Conductivity and Thermal Expansion of Cu-X (X = Cr, B) Diamond Composites, Scr. Mater., 2007, 57(11), p 988-99110.1016/j.scriptamat.2007.08.007 ↗
19. N. Ali, W. Ahmed, C.A. Rego, and Q.H. Fan, Chromium Interlayers as a Tool for Enhancing Diamond Adhesion on Copper, Diam. Relat. Mater., 2000, 9, p 1464-147010.1016/S0925-9635(00)00266-1 ↗
20. W.Q. Qiu, Z.W. Liu, L.X. He, D.C. Zeng, and Y.W. Mai, Improved Interfacial Adhesion Between Diamond Film and Copper Substrate Using a Cu(Cr)-Diamond Composite Interlayer, Mater. Lett., 2012, 81, p 155-15710.1016/j.matlet.2012.05.015 ↗
21. M. Cartier, Handbook of Surface Treatments and Coatings, ASME Press, New York, NY, 2003
22. P. Fauchais, A. Vardelle, and B. Dussoubs, Quo Vadis Thermal Spray, J. Therm. Spray Technol., 2001, 10(1), p 44-6610.1361/105996301770349510 ↗
23. P. Fauchais, M. Fukumoto, A. Vardelle, and M. Vardelle, Knowledge Concerning Splat Formation: An Invited Review, J. Therm. Spray Technol., 2004, 13(3), p 337-36010.1361/10599630419670 ↗
24. C. Xu, C.C. Jia, H. Guo, Z.H. Bai, and M. Li, Effect of Electroless Nickel Plating Process on the Properties of the Plating Layer on Diamond/Cu Composite Materials, Journal of University of Science and Technology Beijing, 2013, 35(11), p 1500-1506 ((in Chinese))
25. Thermal Conductivities of the Elements. https://en.wikipedia.org/wiki/Thermal_conductivities_of_the_elements_(data_page)
26. D.C. Giancoli, Physics for Scientists and Engineers with Modern Physics, 4th ed., Published by Pearson Education, 2008, ISBN 9780131495081
27. T. Schmidt, F. Gaertner, and H. Kreye, New Developments in Cold Spray Based on Higher Gas and Particle Temperatures, J. Therm. Spray Technol., 2006, 15(4), p 488-49410.1361/105996306X147144 ↗
28. M. Fukumoto, M. Mashiko, M. Yamada, and E. Yamaguchi, Deposition Behavior of Copper Fine Particles onto Flat Substrate Surface in Cold Spraying, J. Therm. Spray Technol., 2010, 19(1-2), p 89-9410.1007/s11666-009-9426-y ↗
29. S. Kuroda, J. Kawakita, M. Watanabe, and H. Katanoda, Warm Spraying—A novel Coating Process Based on High-Velocity Impact of Solid Particles, Technol. Adv. Mater, Sci, 2008, doi: 10.1088/1468-6996/9/3/03300210.1088/1468-6996/9/3/033002 ↗
30. H. Katanoda, T. Kiriaki, T. Tachibanaki, J. Kawakita, S. Kuroda, and M. Fukuhara, Mathematical Modeling and Experimental Validation of the Warm Spray (Two-Stage HVOF) Process, J. Therm. Spray Technol., 2009, 18(3), p 401-41010.1007/s11666-009-9299-0 ↗
31. S. Kuroda, M. Watanabe, K. Kim, and H. Katanoda, Current Status and Future Prospects of Warm Spray Technology, J. Therm. Spray Technol., 2011, 20(4), p 653-67610.1007/s11666-011-9648-7 ↗
32. Q.S. Lin, K.S. Zhou, C.M. Deng, M. Liu, X.L. Xiao, and C.G. Deng, Deposition Behavior and Microstructural Development of TiNi Powder particles in Low Temperature-HVOF Spraying Process, Appl. Surf. Sci., 2013, 283, p 352-35910.1016/j.apsusc.2013.06.115 ↗
33. Q.S. Lin, K.S. Zhou, C.M. Deng, M. Liu, L.P. Xu, and C.G. Deng, Deposition Mechanisms and Oxidation Behaviors of Ti-Ni Coatings Deposited in Low-Temperature HVOF Spraying Process, J. Therm. Spray Technol., 2014, 23(6), p 892-90210.1007/s11666-014-0117-y ↗
34. A. Wank, A. Schwenk, M. Liu, K.S. Zhou, C.M. Deng, and C.G. Deng, Expansion of the Applicable Range of HVOF Process Conditions, Thermal Spray 2010: Global Solutions for Future Applications, Proceedings of the International Thermal Spray Conference, B.R. Marple, A. Agarwal, M.M. Hyland, Y.-C. Lau, C.-J. Li, R.S. Lima, and G. Montavon, Ed., May 3-5, 2010 (Singapore), CD-ROM10.31399/asm.cp.itsc2010p0455 ↗
35. K. Yang, M. Liu, and C. Deng, Adhesion Strength of Cu Coating on Substrate at Different Temperatures, Surf. Eng., 2014, 30(11), p 814-82210.1179/1743294414Y.0000000320 ↗
36. W.S. Rasband, ImageJ, U. S. National Institutes of Health, Bethesda, MA, 1997
37. V. Pershin, M. Lufitha, S. Chandra, and J. Mostaghimi, Effect of Substrate Temperature on Adhesion Strength of Plasma-Sprayed Nickel Coatings, J. Therm. Spray Technol., 2003, 12(3), p 370-37610.1361/105996303770348249 ↗
38. K. Yang, M. Fukumoto, T. Yasui, and M. Yamada, Study of Substrate Preheating on Flattening Behavior of Thermal-Sprayed Copper Particles, J. Therm. Spray Technol., 2010, 19(6), p 1195-120510.1007/s11666-010-9515-y ↗
39. A. Vardelle, C. Moreau, and P. Fauchais, Deposit Formation Dynamics, MRS Bull., 2000, July, p 32-3710.1557/mrs2000.121 ↗
40. P.M. Scott, M. Nicholas, and B. Dewar, The Wetting and Bonding of Diamonds by Copperbase Binary Alloys, J. Mater. Sci., 1975, 10, p 1833-184010.1007/BF00754470 ↗
41. C.J. Li and J.L. Li, Transient Contact Pressure During Flattening of Thermal Spray Droplet and Its Effect on Splat Formation, J. Therm. Spray Technol., 2004, 13(2), p 229-23810.1361/10599630418158 ↗
42. C.J. Li and J.L. Li, Evaporated-Gas-Induced Splashing Model for Splat Formation During Plasma Spraying, Surf. Coat. Technol., 2004, 184, p 13-2310.1016/j.surfcoat.2003.10.048 ↗
43. J. Kawakita, K. Isoyama, S. Kuroda, and H.I. Yumoto, Effects of Deformability of HVOF Sprayed Copper Particles on the Density of Resultant Coatings, Surf. Coat. Technol., 2006, 200, p 4414-442310.1016/j.surfcoat.2005.02.180 ↗