Fabrication and Wear Behavior of Nanostructured Plasma-Sprayed 6061Al-SiCp Composite Coating
Source abstract
Abstract
6061Al powder with 15 wt.% SiC particulate (SiCp) reinforcement was mechanically alloyed (MA) in a high-energy attrition mill. The MA powder was then plasma sprayed onto weathering steel (Cor-Ten A242) substrate using an atmospheric plasma spray process. Results of particle size analysis and scanning electron microscopy show that the addition of SiC particles as the reinforcement influences on the matrix grain size and morphology. XRD studies revealed embedment of SiCp in the MA-processed composite powder, and nanocrystals in the MA powder and the coating. Microstructural studies showed a uniform distribution of reinforced SiC particles in the coating. The porosity level in the coating was as low as 2% while the coating hardness was increased to 232VHN. The adhesion strength of the coatings was high and this was attributed to higher degree of diffusion at the interface. The wear rate in the coatings was evaluated using a pin-on-disk type tribometer and found to decrease by 50% compared to the 6061Al matrix coating. The wear mechanism in the coating was delamination and oxidative type.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · High-Temperature Coating Behaviors · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (34)
Show source-provided references
1. J.A. Hookery and P.J. Doorbar, Metal Matrix Composites for Aero Engines, Mater. Sci. Technol., 2000, 16, p 725-73110.1179/026708300101508414 ↗
2. F.H. Froes, Advanced Metals for Aerospace and Automotive Use, Mater. Sci. Eng. A, 1994, 184, p 119-13310.1016/0921-5093(94)91026-X ↗
3. M. Kok and K. Ozdin, Wear Resistance of Aluminium Alloy and its Composites Reinforced by Al2O3 Particles, J. Mater. Process. Technol., 2007, 183, p 301-30910.1016/j.jmatprotec.2006.10.021 ↗
4. T.G. Durai, K. Das, and S. Das, Synthesis and Characterization of Al Matrix Composites Reinforced by In-Situ Alumina Particulates, Mater. Sci. Eng. A., 2007, 445-446, p 100-10510.1016/j.msea.2006.09.018 ↗
5. H. Mindivan, E.S. Kayali, and H. Cimenoglu, Tribological Behavior of Squeeze Cast Aluminum Matrix Composites Wear, 2008, 265, p 645-654
6. M.A. Dellis, J.P. Keastenrmans, and F. Delannay, The Wear Properties of Aluminium Alloy Composite, Mater. Sci. Eng. A, 1991, 135, p 253-25710.1016/0921-5093(91)90572-5 ↗
7. P. Rohatgi, Cast Aluminum-Matrix Composites for Automotive Applications, JOM, 1991, 43(4), p 10-1510.1007/BF03220538 ↗
8. J. Dinwoodie, Automotive Applications for MMCs Based on Short Staple Alumina Fibres, SAE Technical Paper Series, International Congress and Exposition, Detroit Michigan, 1987, p 23-2710.4271/870437 ↗
9. M.J. Kocazac, S.C. Khatri, J.E. Allison, and M. G. Bader, MMCs for Ground Vehicle Aerospace and Industrial Applications, Fundamentals of Metal Matrix Composites, Suresh, et al., Eds., Butterworths, Guildford, 199310.1016/B978-0-08-052371-2.50020-1 ↗
10. A.M. Al-Qutub, I.M. Allam, and T.W. Qureshi, Wear Properties of 10% Submicron A1201/6061 Aluminum Alloy Composite, Int. J. Appl. Mech. Eng., 2002, 7, p 329-334
11. D.C. Jia, Influence of SiC Particulate Size on the Microstructural Evolution and Mechanical Properties of Al-6Ti-6Nb Matrix Composites, Mater. Sci. Eng. A, 2000, 289, p 83-9010.1016/S0921-5093(00)00897-2 ↗
12. T. Yamasaki, Y.J. Zheng, Y. Ogino, M. Terasawa, T. Mitamura, and T. Fukami, Formation of Metal-TiN/TiC Nanocomposite Powders by Mechanical Alloying and their Consolidation, Mater. Sci. Eng. A, 2003, 350, p 168-17210.1016/S0921-5093(02)00722-0 ↗
13. K.I. Moon and K.S. Lee, Study of the Microstructure of Nanocrystalline Al-Ti Alloys Synthesized by Ball Milling in a Hydrogen Atmosphere and Hot Extrusion, J. Alloys Compd., 1999, 291, p 312-32110.1016/S0925-8388(99)00299-6 ↗
14. K.M. Mussert, W.P. Vellinga, A. Bakker, and S. Van Der Zwaag, A Nano-indentation Study on the Mechanical Behaviour of the Matrix Material in an AA6061-Al2O3 MMC, Mater. Sci., 2002, 37, p 789-79410.1023/A:1013896032331 ↗
15. D.Y. Ying and D.L. Zhang, Processing of Cu-Al2O3 Metal Matrix Nanocomposite Materials by Using High Energy Ball Milling, Mater. Sci. Eng. A, 2000, 286, p 152-15610.1016/S0921-5093(00)00627-4 ↗
16. N. Zhao, P. Nash, and X. Yang, The Effect of Mechanical Alloying on SiC Distribution and the Properties of 6061 Aluminum Composite, J. Mater. Process. Technol., 2005, 170, p 586-59210.1016/j.jmatprotec.2005.06.037 ↗
17. J. Ye, B.Q. Han, Z. Lee, B. Ahn, S.R. Nutt, and J.M. Schoenung, A Tri-modal Aluminum Based Composite with Super-High Strength, Scr. Mater., 2005, 53, p 481-48610.1016/j.scriptamat.2005.05.004 ↗
18. S. Tailor, V.K. Sharma, R.M. Mohanty, and P.R. Soni, Study of the Effects of Mechanically Alloying on 2024AI with SiCp and on Plasma Sprayed Coatings, Proceedings of EURO PM 2011 International Powder Metallurgy Congress & Exhibition, vol 2, 9-12th October 2011(Barcelona, Spain), EPMA, 2011, p 91-96
19. T.S. Sidhu, S. Prakash, and R.D. Agarwal, Performance of High-Velocity Oxyfuel-Sprayed Coatings on a Fe-Based Superalloy in Na2SO4-60%V2O5 Environment at 900 °C Part I: Characterization of the Coatings, J. Mater. Eng. Perform., 2006, 15, p 122-12910.1361/105994906X83402 ↗
20. I. Ozdemir, I. Hamanaka, M. Hirose, Y. Tsunekawa, and M. Okumiya, In-Situ Formation of Al-Si-Mg Based Composite Coating by Different Reactive Thermal Spray Processes, Surf. Coat. Technol., 2005, 200(1-4), p 1155-116110.1016/j.surfcoat.2005.01.117 ↗
21. C. Tekmen, M. Yamazaki, Y. Tsunekawa, and M. Okumiya, In-Situ Plasma Spraying: Alumina Formation and In-flight Particle Diagnostic, Surf. Coat. Technol., 2008, 202, p 4163-416910.1016/j.surfcoat.2008.03.013 ↗
22. C. Tekmen, Y. Tsunekawa, and M. Okumiya, In-Situ TiB2 and Al2O3 Formation by DC Plasma Spraying, Surf. Coat. Technol., 2008, 202, p 4170-417510.1016/j.surfcoat.2008.03.012 ↗
23. G.K. Williamson and W.H. Hall, X-ray Line Broadening from Filed Al and W, Acta Metall., 1953, 1, p 22-3110.1016/0001-6160(53)90006-6 ↗
24. P. Araujo, D. Chicot, M. Staia, and J. Lesage, Residual Stresses and Adhesion of Thermal Spray Coatings, Surf. Eng., 2005, 21, p 35-4010.1179/174329405X30020 ↗
25. J.R. Cahoon, W.H. Broughton, and A.R. Kutzak, The Determination of Yield Strength from Hardness Measurements, Metall. Trans., 1971, 2(7), p 1979-198310.1007/BF02913433 ↗
26. P.R. Soni, Mechanical Alloying: Fundamentals & Applications, Cambridge International Science Publishing, Cambridge, 2001
27. S. Tailor, R.M. Mohanty, and P.R. Soni, A Review on Plasma Sprayed Al-SiC Composite Coatings, J. Mater. Sci. Surf. Eng., 2013, 1(1), p 15-22
28. T.H. Van Steenkiste, A. Elmoursi, D. Gorkiewicz, and B. Gillispie, Fracture Study of Aluminum Composite Coatings Produced by the Kinetic Spray Method, Surf. Coat. Technol., 2005, 194, p 103-11010.1016/j.surfcoat.2004.05.005 ↗
29. M. Shorowordi, T. Laouip, A.S.M.A. Haseeb, J.P. Celis, and L. Froyen, Microstructure and Interface Characteristics of B4C, SiC and Al2O3 Reinforced Al Matrix Composites: A Comparative Study, J. Mater. Process Technol., 2003, 142, p 738-74310.1016/S0924-0136(03)00815-X ↗
30. R.A. Saravanan, J.M. Lee, and S.B. Kang, Dry Sliding Wear Behaviour of A356-15 Pct SiCp Composites Under Controlled Atmospheric Conditions, Metall. Mater. Trans. A, 1999, 30A, p 2523-253810.1007/s11661-999-0261-z ↗
31. Z.F. Zhang, L.C. Zhang, and Y.W. Mai, Particle Effects on Friction and Wear of Aluminium Matrix Composites, J. Mater. Sci., 1995, 30, p 5999-600410.1007/BF01151519 ↗
32. K.C. Ludema, A Review of Scuffing and Running-in of Lubricated Surfaces with Asperities and Oxides in Perspective, Wear, 1984, 100, p 315-33110.1016/0043-1648(84)90019-X ↗
33. J.A. Williams, I.N. Dyson, and A. Kapoor, Repeated Loading, Residual Stresses, Shakedown and Tribology, J. Mater Res., 1999, 14, p 1548-155910.1557/JMR.1999.0208 ↗
34. J.A. Williams, Wear and Wear Particles: Some Fundamentals, Tribol. Int., 2005, 38, p 863-87010.1016/j.triboint.2005.03.007 ↗