Improvements in Cavitation and Slurry Wear Erosion of Inconel 718 Laser Cladding Through NiNb Addition
Source abstract
Abstract
Abstract The development of materials and alloys for coatings has been increasingly important for reducing costs in different manufacturing processes. The Inconel alloy is widely used due to its chemical inertness and high resistance to high temperatures, but it does not present adequate resistance to erosive wear. In this context, the resistance to wear from cavitation erosion and slurry erosion was evaluated of samples with depositions obtained by laser cladding (Laser directed energy deposition - L-DED) of Inconel 718 and Inconel 718+10%NiNb. The cavitation erosion wear tests were carried out following the ASTM G32 standard (2016), and the ASTM G73-10 standard (2017) was used to evaluate the resistance to slurry erosion wear. The scanning electron microscopy technique (SEM-EDS), and X-ray diffraction (XRD) were used to characterize the cross-section and the surface after wear. The wear mechanism was checked and identified. Microhardness profiles of the cladding cross-section were carried out. The mass loss and wear rate due to cavitation and slurry jet erosion of Inconel 718 and Inconel 718+ 10% NiNb coatings were determined. It was proven that the addition of 10% NiNb in the formation of the cladding caused a 45% increase in average microhardness in the cross-section of the Inconel 718 cladding. The addition of 10% NiNb to the Inconel 718 cladding caused a decrease in mass loss due to slurry erosion from 38.9 mg to 21.9 mg (33%) when the erodent impact angle was 60°.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · High-Temperature Coating Behaviors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. Y. Zhang et al., Grain Growth of Ni-Based Superalloy IN718 Coating Fabricated by Pulsed Laser Deposition, Opt. Laser Technol., 2016, 80, p 220–226. https://doi.org/10.1016/j.optlastec.2016.01.01510.1016/j.optlastec.2016.01.015 ↗
2. S. Singh, D.K. Goyal, P. Kumar and A. Bansal, Laser Cladding Technique for Erosive Wear Applications: a Review, Mater Res Express., 2020, 7(1), p 012007.10.1088/2053-1591/ab6894 ↗
3. R.L. Sun, J.F. Mao and D.Z. Yang, Microstructural Characterization of NiCr1BSiC Laser Clad Layer on Titanium Alloy Substrate, Surf. Coat. Technol., 2002, 150, p 199–204.10.1016/S0257-8972(01)01512-2 ↗
4. S. Liu, W. Liu, M. Harooni, J. Ma and R. Kovacevic, Real-Time Monitoring of Laser Hot-Wire Cladding of Inconel 625, Opt. Laser Technol., 2014, 62, p 124–134.10.1016/j.optlastec.2014.03.007 ↗
5. Y.C. Zhang, Z.G. Li, P.L. Nie and Y.X. Wu, Carbide and Nitride Precipitation During Laser Cladding of Inconel 718 Alloy Coatings, Opt. Laser Technol., 2013, 52, p 30–36.10.1016/j.optlastec.2013.03.023 ↗
6. C. Hong, D. Gu, D. Dai, A. Gasser, A. Weisheit, I. Kelbassa, M. Zhong and R. Poprawe, Laser Metal Deposition of TiC/Inconel 718 Composites with Tailored Interfacial Microstructures, Opt. Laser Technol., 2013, 54, p 98–109.10.1016/j.optlastec.2013.05.011 ↗
7. H. Zhang, Y. Zou, Z. Zou and D. Wu, Microstructure and Properties of Fe-Based Composite Coating by Laser Cladding Fe–Ti–V–Cr–C–CeO2 Powder, Opt. Laser Technol., 2015, 65, p 119–125.10.1016/j.optlastec.2014.06.016 ↗
8. A. Arunachaleswaran, I.M. Pereira, H. Dieringa, Y. Huang, N. Hort, B.K. Dhindaw and K.U. Kainer, Creep Behavior of AE42 Based Hybrid Composites, Mater. Sci. Eng. A, 2007, 460–461, p 268–276.10.1016/j.msea.2007.01.043 ↗
9. Y.C. Lin, Y.C. Lin and Y.C. Chen, Evolution of the Microstructure and Tribological Performance of Ti–6Al–4V Cladding with TiN Powder, Mater. Des., 2012, 36, p 584–589.10.1016/j.matdes.2011.12.007 ↗
10. H. Zhang, Y. Pan and Y.Z. He, Synthesis and Characterization of FeCoNiCrCu High Entropy Alloy Coating by Laser Cladding, Mater. Des., 2011, 32, p 1910–1915.10.1016/j.matdes.2010.12.001 ↗
11. C. Huang, Y. Zhang, J. Shen and R. Vilar, Thermal Stability and Oxidation Resistance of Laser Clad TiVCrAlSi High Entropy Alloy Coatings on Ti–6Al–4V Alloy, Surf. Coat. Technol., 2011, 206, p 89–1395.
12. X. Zhao, J. Chen, X. Lin and W. Huang, Study on Microstructure and Mechanical Properties of Laser Rapid Forming Inconel 718, Mater. Sci. Eng. A, 2008, 478, p 119–124.10.1016/j.msea.2007.05.079 ↗
13. I. Tabernero, A. Lamikiz, S. Martínez, E. Ukar and J. Figueras, Evaluation of the Mechanical Properties of Inconel 718 Components Built by Laser Cladding, Int. J. Mach. Tool Manuf., 2011, 51(6), p 465–70.10.1016/j.ijmachtools.2011.02.003 ↗
14. T. Lindner, A. Günen, G. Töberling, S. Vogt, M.S. Karakas, M. Löbel et al., Boriding of Laser-Clad Inconel 718 Coatings for Enhanced Wear Resistance, Appl. Sci., 2021, 11(24), p 11935.10.3390/app112411935 ↗
15. P. Deng, C. Yao, K. Feng, X. Huang, Z. Li, Y. Li et al., Enhanced Wear Resistance of Laser Cladded Graphene Nanoplatelets Reinforced Inconel 625 Superalloy Composite Coating, Surf. Coat. Technol., 2018, 335, p 334–344.10.1016/j.surfcoat.2017.12.047 ↗
16. S. Lu, J. Zhou, L. Wang and J. Liang, Influence of MoSi2 on the Microstructure and Elevated-Temperature Wear Properties of Inconel 718 Coating Fabricated by Laser Cladding, Surf. Coat. Technol., 2021, 424, p 127665.10.1016/j.surfcoat.2021.127665 ↗
17. J. Ning, Q. Lan, L. Zhu, L. Xu, Z. Yang, P. Xu et al., Microstructure and Mechanical Properties of SiC-Reinforced inconel 718 Composites Fabricated by Laser Cladding, Surf. Coat. Technol., 2023, 463, p 129514.10.1016/j.surfcoat.2023.129514 ↗
18. T. Wang, C. Wang, J. Li, L. Chai, X. Hu, Y. Ma et al., Microstructure and Wear Properties of Laser-Clad NiCo Alloy Coating on Inconel 718 Alloy, J. Alloy. Compd., 2021, 879, p 160412.10.1016/j.jallcom.2021.160412 ↗
19. Y.C. Zhang, Z.G. Li, P.L. Nie and Y.X. Wu, Effect of Ultrarapid Cooling on Microstructure of Laser Cladding IN718 Coating, Surf. Eng., 2013, 29(6), p 414–418.10.1179/1743294413Y.0000000142 ↗
20. J. Natarajan and C.-H. Yang, Laser Surface Treatments for Tribological Applications, Bentham Sci. Publishers, 2021 https://doi.org/10.2174/9789815036305121010110.2174/97898150363051210101 ↗
21. M. Ma, Z. Wang and X. Zeng, Effect of Energy Input on Microstructural Evolution of Direct Laser Fabricated IN718 Alloy, Mater. Charact., 2015, 106, p 420–427.10.1016/j.matchar.2015.06.027 ↗
22. L.L. Parimi, G.A. Ravi, D. Clark and M.M. Attallah, Microstructural and Texture Development in Direct Laser Fabricated IN718, Mater. Charact., 2014, 89, p 102–111.10.1016/j.matchar.2013.12.012 ↗
23. H. Xie, K. Yang, F. Li, C. Sun and Z. Yu, Investigation on the Laves Phase Formation During Laser Cladding of IN718 Alloy by CA-FE, J. Manuf. Process., 2020, 52, p 132–144.10.1016/j.jmapro.2020.01.050 ↗
24. F. Liu, F. Lyu, F. Liu, X. Lin and C. Huang, Laves Phase Control of Inconel 718 Superalloy Fabricated by Laser Direct Energy Deposition via δ Aging and Solution Treatment, J. Market. Res., 2020, 9(5), p 9753–9765.
25. M. Ahmad et al., Structure, Texture and Phases in 3D Printed IN718 Alloy Subjected to Homogenization and HIP Treatments, Metals, 2017, 7, p 196. https://doi.org/10.3390/met706019610.3390/met7060196 ↗
26. S.G.K. Manikandan, D. Sivakumar, K. Prasad Rao and M. Kamaraj, Laves Phase in Alloy 718 Fusion Zone — Microscopic and Calorimetric Studies, Mater. Charact., 2015, 100, p 192–206.10.1016/j.matchar.2014.11.035 ↗
27. Xu. Zhenyang et al., Effect of Laser Cladding Parameters on Inconel 718 Coating Performance and Multi-Parameter Optimization”, Opt. Laser Technol., 2023, 158, p 108850. https://doi.org/10.1016/j.optlastec.2023.10948910.1016/j.optlastec.2023.109489 ↗
28. J. Chen et al., Grain Refinement and Laves Phase Dispersion by High-Intensity Ultrasonic Vibration in Laser Cladding of Inconel 718, J. Market. Res., 2024, 30, p 8563–8575. https://doi.org/10.1016/j.jmrt.2024.05.22910.1016/j.jmrt.2024.05.229 ↗
29. Q. Zhang, L. Wu, H. Zou et al., Correlation Between Microstructural Characteristics and Cavitation Resistance of Stellite-6 Coatings on 17–4 PH Stainless Steel Prepared with Supersonic Laser Deposition and Laser Cladding, J. Alloy. Compd., 2021, 860, p 158417. https://doi.org/10.1016/j.jallcom.2020.15841710.1016/j.jallcom.2020.158417 ↗
30. G. Taillon and K. Miyagawa, Cavitation Erosion of Ni-Based Superalloys Manufactured by Forging and Additive Manufacturing, J Fail. Anal. and Preven., 2021, 21, p 1902–1917. https://doi.org/10.1007/s11668-021-01241-410.1007/s11668-021-01241-4 ↗
31. M. Kazasidis et al., Microstructure and Cavitation Erosion Performance of Nickel-Inconel 718 Composite Coatings Produced with Cold Spray, Surf. Coat. Technol., 2020, 382, p 125195. https://doi.org/10.1016/j.surfcoat.2019.12519510.1016/j.surfcoat.2019.125195 ↗
32. V. Singh et al., Influence of TiC Content on Slurry Erosion Behaviour of HVOF Sprayed Titanium Carbide and Cupronickel-Chromium Based Coatings, J Therm Spray Tech, 2023, 32, p 1739–1757. https://doi.org/10.1007/s11666-023-01613-210.1007/s11666-023-01613-2 ↗
33. S. Zafar et al., Dry Erosion Wear Performance of Inconel 718 Microwave Clad, Surf. Eng., 2014 https://doi.org/10.1179/1743294414Y.000000035910.1179/1743294414Y.0000000359 ↗