Evaluation of Strain Field Around Impacted Particles by Applying Electron Moiré Method
Source abstract
Abstract
Recently, the thermal-spray community has focused considerable attention on cold-spray and warm-spray techniques, in which the temperatures of sprayed particles are kept below their melting point and adhesion occurs based on the impact phenomenon between a solid particle and a substrate. The mechanisms of adhesion are still unclear, but the degree of the mechanical deformation at the interface is considered to be a key factor influencing this mechanism. However, it is very difficult to directly measure the strain at the interface. Instead, in this work, the strain fields on a substrate around an impacted particle sprayed by warm-spray deposition were measured by applying electron Moire method, and compared with numerical simulation results.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Fluid Dynamics and Heat Transfer · Particle Dynamics in Fluid Flows
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. S.V. Klinkov, V.F. Kosarev, M. Rein 2005 Cold Spray Deposition: Significance of Particle Impact Phenomena. Aerosp. Sci. Technol., 9(7), 582–59110.1016/j.ast.2005.03.005 ↗
2. E. Calla, D.G. McCartney, P.H. Shipway 2006 Effect of Deposition Conditions on the Properties and Annealing Behavior of Cold-Sprayed Copper. J. Therm. Spray Technol., 15(2), 255–26210.1361/105996306X108192 ↗
3. H.J. Kim, C.H. Lee, S.Y. Hwang 2005 Superhard Nano Wc-12%Co Coating by Cold Spray Deposition. Mater. Sci. Eng. A: Struct. Mater. Prop. Microstruct. Process., 391(1–2), 243–248
4. J. Kawakita, S. Kuroda, T. Fukushima, H. Katanoda, K. Matsuo, H. Fukanuma 2006 Dense Titanium Coatings by Modified HVOF Spraying. Surf. Coat. Technol., 201(3–4), 1250–125510.1016/j.surfcoat.2006.01.056 ↗
5. T. Marrocco, D.G. McCartney, P.H. Shipway, A.J. Sturgeon 2006 Production of Titanium Deposits by Cold-Gas Dynamic Spray: Numerical Modeling and Experimental Characterization. J. Therm. Spray Technol., 15(2), 263–27210.1361/105996306X108219 ↗
6. K. Sakaki, Y. Shimizu 2001 Effect of the Increase in the Entrance Convergent Section Length of the Gun Nozzle on the High-Velocity Oxygen Fuel and Cold Spray Process. J. Therm. Spray Technol., 10(3), 487–49610.1361/105996301770349268 ↗
7. S. Kuroda, Y. Tashiro, H. Yumoto, S. Taira, H. Fukanuma, S. Tobe 2001 Peening Action and Residual Stresses in High-Velocity Oxygen Fuel Thermal Spraying of 316l Stainless Steel. J. Therm. Spray Technol., 10(2), 367–37410.1361/105996301770349457 ↗
8. S. Kuroda, J. Kawakita, T. Fukushima, S. Tobe 2003 Importance of the Adhesion of HVOF Sprayed Coatings for Aqueous Corrosion Resistance. Mater. Trans., 44(3), 381–38810.2320/matertrans.44.381 ↗
9. M. Watanabe, A. Owada, S. Kuroda, Y. Gotoh 2006 Effect of Wc Size on Interface Fracture Toughness of Wc-Co HVOF Sprayed Coatings. Surf. Coat. Technol., 201(3-4), 619–62710.1016/j.surfcoat.2005.12.019 ↗
10. C.J. Li, W.Y. Li, H.L. Liao 2006 Examination of the Critical Velocity for Deposition of Particles in Cold Spraying. J. Therm. Spray Technol., 15(2), 212–22210.1361/105996306X108093 ↗
11. H. Assadi, F. Gärtner, T. Stoltenhoff, H. Kreye 2003 Bonding Mechanism in Cold Gas Spraying. Acta Mater., 51(15), 4379–439410.1016/S1359-6454(03)00274-X ↗
12. T. Schmidt, F. Gärtner, H. Assadi, H. Kreye 2006 Development of a Generalized Parameter Window for Cold Spray Deposition. Acta Mater., 54(3), 729–74210.1016/j.actamat.2005.10.005 ↗
13. S. Kishimoto, M. Egashira, N. Shinya 1993 Microcreep Deformation Measurements by a Moiré Method Using Electron-Beam Lithography and Electron-Beam Scan. Opt. Eng., 32(3), 522–52610.1117/12.61046 ↗
14. S. Kishimoto, H.M. Xie, N. Shinya 2000 Electron Moiré Method and Its Application to Micro-Deformation Measurement. Opt. Lasers Eng., 34(1), 1–1410.1016/S0143-8166(00)00078-6 ↗
15. H.M. Xie, S. Kishimoto, A. Asundi, C.G. Boay, N. Shinya, J. Yu, B.K.A. Ngoi 2000 In-Plane Deformation Measurement Using the Atomic Force Microscope Moiré Method. Nanotechnology, 11(1), 24–2910.1088/0957-4484/11/1/305 ↗
16. S. Kishimoto, N. Shinya, M.D. Mathew 1997 Application of Electron Beam Lithography to Study Microcreep Deformation and Grain Boundary Sliding. J. Mater. Sci., 32(13), 3411–341710.1023/A:1018668616331 ↗
17. G.R. Johnson, W.H. Cook 1985 Fracture Characteristics of 3 Metals Subjected to Various Strains, Strain Rates, Temperatures and Pressures. Eng. Fract. Mech., 21(1), 31–4810.1016/0013-7944(85)90052-9 ↗
18. G.R. Johnson 1993 Material Characterization for Warhead Computations. Prog. Astronaut. Aeronaut., 155, 165–197
19. D. Zhao, Hot Tension and Compression Testing, ASM Handbook, H. Kuhn and Dana Medlin, Eds., ASM International, 2000, Vol. 8, p 152-16310.31399/asm.hb.v08.a0003266 ↗
20. K. Yokoyama, M. Watanabe, S. Kuroda, Y. Gotoh, T. Schmidt, F. Gärtner 2006 Simulation of Solid Particle Impact Behavior for Spray Processes. Mater. Trans., 47(7), 1697–170210.2320/matertrans.47.1697 ↗
21. J. Kawakita, K. Isoyama, S. Kuroda, H. Yumoto 2006 Effects of Deformability of HVOF Sprayed Copper Particles on the Density of Resultant Coatings. Surf. Coat. Technol., 200(14-15), 4414–442310.1016/j.surfcoat.2005.02.180 ↗
22. T. Wu, S. Kuroda, J. Kawakita, H. Katanoda, and R. Reed, Processing and Properties of Titanium Coating Produced by Warm Spraying, Proceedings of the 2006 International Thermal Spray Conference, 200610.31399/asm.cp.itsc2006p0631 ↗
23. K. Shinoda, Y. Kojima, T. Yoshida 2005 In Situ Measurement System for Deformation and Solidification Phenomena of Yttria-Stabilized Zirconia Droplets Impinging on Quartz Glass Substrate under Plasma-Spraying Conditions. J. Therm. Spray Technol., 14(4), 511–51710.1361/105996305X76531 ↗
24. K. Shinoda, T. Koseki, and T. Yoshida, Influence of Impact Parameters of Zirconia Droplets on Splat Formation and Morphology in Plasma Spraying, J. Appl. Phys., 2006, 100(7), Art. No. 07490310.1063/1.2355446 ↗