journal article·2019-06

Effect of Vacuum Hot Pressing on Plasma-Sprayed Molybdenum Coatings on Rail Vehicle Axle Steel

Chunming Liang, Min Yu, Hao Ma, Hui Chen

Publisher page

Abstract

Railway axles suffer severe friction damage during service. In this work, a pure molybdenum coating was prepared on EA4T axle steel by air plasma spraying and hot pressing to improve the steel lifetime. The phase composition, microstructure, hardness, and tribological properties of the coatings were characterized. The results showed that the Mo coating had typical lamellar structure with low porosity and oxidation. Hot pressing compacted the coating and improved the microstructure uniformity. The hardness of the Mo coating and its bonding strength with the substrate were increased after hot pressing under 60 MPa at temperatures ranging between 400 and 500 °C, due to reduced porosity and enhanced mechanical bonding between the coating and substrate. In addition, both the friction coefficient and wear loss of the Mo coating were lower than those of the EA4T steel, illustrating its lubricating effect. Observation of worn surfaces showed that the delamination wear of the Mo coating could be relieved after proper hot pressing due to the strengthened bonding between lamellae.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Metal Alloys Wear and Properties · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. L. Wei, H.Q. Fu, and C.S. Zhong, Fretting Damage Behavior of Rail Vehicle Axle Repaired with Thermally Sprayed Cr-Ni Coatings, Tribology, 2002, 22(6), p 435-438
2. Z. Feng and J.E. Field, Friction of Diamond on Diamond and Chemical Vapour Deposition Diamond Coatings, Surf. Coat. Technol., 1991, 47(1), p 631-64510.1016/0257-8972(91)90335-T ↗
3. J. Halling, The Tribology of Surface Coatings, Particularly Ceramics, ARCHIVE Proc. Inst. Mech. Eng. Part C J. Mech. Eng. Sci. 1989–1996 (vols 203–210), 1986, 200(1), p 31-4010.1243/PIME_PROC_1986_200_091_02 ↗
4. S. Jahanmir, E.P.A. Ii, and N.P. Suh, Sliding Wear Resistance of Metallic Coated Surfaces, Wear, 1976, 40(1), p 75-8410.1016/0043-1648(76)90019-3 ↗
5. J.A. Horwath, Molybdenum Spray Coating of Transmission Synchronizer Rings, Thin Solid Films, 1980, 73(1), p 7910.1016/0040-6090(80)90330-2 ↗
6. B. Hwang, J. Ahn, and S. Lee, Effects of Blending Elements on Wear Resistance of Plasma-Sprayed Molybdenum Blend Coatings Used for Automotive Synchronizer Rings, Surf. Coat. Technol., 2005, 194(2), p 256-26410.1016/j.surfcoat.2004.07.072 ↗
7. G. Akdogan, T.A. Stolarski, and S. Tobe, Surface Fatigue of Molybdenum and Al-Bronze Coatings in Unlubricated Rolling/Sliding Contact, Wear, 2002, 253(3), p 319-33010.1016/S0043-1648(02)00152-7 ↗
8. Z. Liu and M. Hua, Wear Transitions and Mechanisms in Lubricated Sliding of a Molybdenum Coating, Tribol. Int., 1999, 32(9), p 499-50610.1016/S0301-679X(99)00079-1 ↗
9. M. Laribi, A.B. Vannes, and D. Treheux, Study of Mechanical Behavior of Molybdenum Coating Using Sliding Wear and Impact Tests, Wear, 2007, 262(11), p 1330-133610.1016/j.wear.2007.01.018 ↗
10. S.C. Modi and E. Calla, A Study of High-Velocity Combustion Wire Molybdenum Coatings, J. Therm. Spray Technol., 2001, 10(3), p 480-48610.1361/105996301770349259 ↗
11. P. Fauchais, Understanding Plasma Spraying, J. Phys. D Appl. Phys., 2004, 37(9), p 8610.1088/0022-3727/37/9/R02 ↗
12. S. Usmani and S. Sampath, Time-Dependent Friction Response of Plasma-Sprayed Molybdenum, Wear, 1999, 225(5273), p 1131-114010.1016/S0043-1648(98)00395-0 ↗
13. R.B. Heimann, Plasma Spray Coating, Wiley, 2008, 102(3), p 7035-7040
14. S.S. Manjunatha and S. Basavarajappa, Effect of Powder Particle Size on Wear Resistance of Plasma Sprayed Molybdenum Coating, ARCHIVE Proc. Inst. Mech. Eng. Part J J. Eng. Tribol. 1994–1996 (vols 208–210), 2014, 228(7), p 789-79610.1177/1350650114531744 ↗
15. T.A. Stolarski and S. Tobe, The Effect of Spraying Distance on Wear Resistance of Molybdenum Coatings, Wear, 2001, 249(12), p 1096-110210.1016/S0043-1648(01)00842-0 ↗
16. J. Yan, Z. He, Y. Wang, J. Qiu, and Y. Wang, Microstructure and Wear Resistance of Plasma-Sprayed Molybdenum Coating Reinforced by MoSi2 Particles, J. Therm. Spray Technol., 2016, 25(7), p 1322-132910.1007/s11666-016-0440-6 ↗
17. D. Debasish, S. Mantry, D. Behera, and B.B. Jha, Improvement of Microstructural and Mechanical Properties of Plasma Sprayed Mo Coatings Deposited on Al-Si Substrates by Pre-mixing of Mo with TiN Powder, High Temp., 2014, 52(1), p 19-2510.1134/S0018151X14010076 ↗
18. L. Prchlik, J. Gutleber, and S. Sampath, Deposition and Properties of High-Velocity-Oxygen-Fuel and Plasma-Sprayed Mo-Mo2C Composite Coatings, J. Therm. Spray Technol., 2001, 10(4), p 643-65510.1361/105996301770349178 ↗
19. A.C. ASTM 633-13 Standard Test Method for Adhesion or Cohesion Strength of Thermal Spray Coatings, ASTM International, 2017.
20. R.S. Lima, K. Kucuk, and C.C. Berndt, Bimodal Distribution of Mechanical Properties on Plasma Sprayed Nanostructured Partially Stabilized Zirconia, Mater. Sci. Eng. A, 2002, 327(2), p 224-23210.1016/S0921-5093(01)01530-1 ↗
21. C.K. Lin and C.C. Berndt, Statistical Analysis of Microhardness Variations in Thermal Spray Coatings, J. Mater. Sci., 1995, 30, p 111-11710.1007/BF00352139 ↗
22. R.E. Walpole, Introduction to Statistics, Collier Macmillan, New York, 1982
23. X. Deng, G. Zhang, and T. Wang, Microstructure and Wear Resistance of Mo Coating Deposited by Plasma Transferred Arc Process, Mater. Charact., 2017, 131, p 517-52510.1016/j.matchar.2017.07.044 ↗