Design of Residual-Stress-Compensating Molds for Cold Spray Additive Manufacturing Applications
Source abstract
Abstract
A methodical procedure for designing molds for cold spray additive manufacturing has been developed and validated. In a preliminary trial, a cold-sprayed part was shown to deform beyond the spatial tolerances of its defined shape. Based on these data and utilizing a linear elastic model of deformation, a new “compensated” mold with a modified shape was generated. The shape of the part deposited onto the compensated mold was measured to have, at maximum, approximately half the error as in the original trial, demonstrating the potential of such mold compensation as a means of achieving the final dimensional accuracy requirements of cold-sprayed parts.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · High-Temperature Coating Behaviors · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (17)
Show source-provided references
1. V.K. Champagne, Ed., The cold spray materials deposition process: fundamentals and applications, Elsevier, Cambridge, 2007
2. M.R. Rokni, S.R. Nutt, C.A. Widener, V.K. Champagne, and R.H. Hrabe, Review of Relationship between Particle Deformation, Coating Microstructure, and Properties in High-Pressure Cold Spray, J. Therm. Spray Technol., 2017, 26(6), p 1308-135510.1007/s11666-017-0575-0 ↗
3. M.F. Smith, Comparing cold spray with thermal spray coating technologies, The cold spray materials deposition process, V.K. Champagne, Ed., Elsevier, Cambridge, 2007, p 43-6110.1533/9781845693787.1.43 ↗
4. M. Hassani-Gangaraj, D. Veysset, K.A. Nelson, and C.A. Schuh, Melting Can Hinder Impact-Induced Adhesion, Phys. Rev. Lett., 2017, 119(17), p 17570110.1103/PhysRevLett.119.175701 ↗
5. M. Hassani-Gangaraj, D. Veysset, K.A. Nelson, and C.A. Schuh, In-Situ Observations of Single Micro-Particle Impact Bonding, Scr. Mater., 2018, 145, p 9-1310.1016/j.scriptamat.2017.09.042 ↗
6. R. Ghelichi, D. MacDonald, S. Bagherifard, H. Jahed, M. Guagliano, and B. Jodoin, Microstructure and Fatigue Behavior of Cold Spray Coated Al5052, Acta Mater., 2012, 60(19), p 6555-656110.1016/j.actamat.2012.08.020 ↗
7. G. Shayegan, H. Mahmoudi, R. Ghelichi, J. Villafuerte, J. Wang, M. Guagliano, and H. Jahed, Residual Stress Induced by Cold Spray Coating of Magnesium AZ31B Extrusion, Mater. Des., 2014, 60, p 72-8410.1016/j.matdes.2014.03.054 ↗
8. V. Luzin, K. Spencer, and M.X. Zhang, Residual Stress and Thermo-mechanical Properties of Cold Spray Metal Coatings, Acta Mater., 2011, 59(3), p 1259-127010.1016/j.actamat.2010.10.058 ↗
9. E. Lin, Q. Chen, O.C. Ozdemir, S. Müftü, and V.K. Champagne, Effects of Interface Bonding on the Residual Stresses in Cold Sprayed Al-6061: A Numerical Investigation, J. Therm. Spray Technol., 2018, 28(3), p 472-48310.1007/s11666-019-00827-7 ↗
10. V. Luzin, K. Spencer, M. Zhang, N. Matthews, J. Davis, and M. Saleh, Residual stresses in cold spray coatings, Cold-spray coatings, P. Cavaliere, Ed., Springer, Cham, 2018, p 451-48010.1007/978-3-319-67183-3_16 ↗
11. Y.C. Tsui and T.W. Clyne, An Analytical Model for Predicting Residual Stresses in Progressively Deposited Coatings Part 1: Planar Geometry, Thin Solid Films, 1997, 306(1), p 23-3310.1016/S0040-6090(97)00199-5 ↗
12. Y.C. Tsui and T.W. Clyne, An Analytical Model for Predicting Residual Stresses in Progressively Deposited Coatings Part 2: Cylindrical Geometry, Thin Solid Films, 1997, 306(1), p 34-5110.1016/S0040-6090(97)00209-5 ↗
13. A. Sova, S. Grigoriev, A. Okunkova, and I. Smurov, Potential of Cold Gas Dynamic Spray as Additive Manufacturing Technology, Int. J. Adv. Manuf. Technol., 2013, 69(9–12), p 2269-227810.1007/s00170-013-5166-8 ↗
14. S. Yin, P. Cavaliere, B. Aldwell, R. Jenkins, H. Liao, W. Li, and R. Lupoi, Cold Spray Additive Manufacturing and Repair: Fundamentals and Applications, Addit. Manuf., 2018, 21, p 628-650
15. I. Nault and G. Ferguson, Additively Manufacturing Airfoil-Like Shapes with Cold Spray. Solid Freeform Fabrication Conference, August 12–14, 2019, Austin, 2019
16. G. Benenati and R. Lupoi, Development of a Deposition Strategy in Cold Spray for Additive Manufacturing to Minimize Residual Stresses, Proc. CIRP, 2016, 55, p 101-10810.1016/j.procir.2016.08.042 ↗
17. MATLAB (The MathWorks Inc., Natick, 2018)