journal article·2021-06

Suspension Spraying Tip: High Molecular Weight Solvent

J. Cizek, D. Dukovsky, R. Musalek, J. Medricky, T. Tesar, F. Lukac, T. Chraska

Publisher page

Abstract

Abstract In suspension spraying, the two most frequently used solvents are water and ethanol. In this study, we test a potential alternative, a high-molecular weight solvent. Two organic solvents are compared: ethanol (serving as a benchmark, suspension formulated at 10 wt.% solid load) and di-propylene glycol methyl ether (two suspensions at 10 wt.% and 20 wt.%). Submicron alpha-alumina powder is used as a model material to formulate the suspensions. It is shown that ethanol- and ether-based-feedstock coatings are fully comparable in terms of their microstructure, porosity content, surface roughness, and hardness. However, the ether-based coatings exhibit slightly higher levels of α-Al2O3 phase than their ethanol-based counterpart (17 wt.% vs. 6 wt.%). The use of 20 wt.% solid load in the ether solvent leads to a twofold increase in the deposition rate while, as opposed to ethanol, successfully retaining a dense microstructure. Ether also costs less than ethanol and is safer to handle.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Thermal and Kinetic Analysis · Advanced ceramic materials synthesis · Catalytic Processes in Materials Science

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. P. Fauchais, A. Joulia, S. Goutier, C. Chazelas, M. Vardelle, A. Vardelle, Suspension and solution plasma spraying. J. Phys. D: Appl. Phys. 46(22), 224015 (2013)10.1088/0022-3727/46/22/224015 ↗
2. F.L. Toma, A. Potthoff, L.M. Berger, C. Leyens, Demands, potentials, and economic aspects of thermal spraying with suspensions: a critical review. J. Therm. Spray Technol. 24(7), 1143–1152 (2015)10.1007/s11666-015-0274-7 ↗
3. M. Aghasibeig, F. Tarasi, R.S. Lima, A. Dolatabadi, C. Moreau, A review on suspension thermal spray patented technology evolution. J. Therm. Spray Technol. 28(7), 1579–1605 (2019)10.1007/s11666-019-00904-x ↗
4. P. Fauchais, M. Vardelle, A. Vardelle, S. Goutier, What do we know, what are the current limitations of suspension plasma spraying? J. Therm. Spray Technol. 24(7), 1120–1129 (2015)10.1007/s11666-015-0286-3 ↗
5. E. Medvedovski, Wear-resistant alumina ceramics. InterCeram Int. Ceram. Rev. 49, 106–113 (2000)
6. E. Medvedovski, Wear-resistant engineering ceramics. Wear 249(9), 821–828 (2001)10.1016/S0043-1648(01)00820-1 ↗
7. J. Medricky, F. Lukac, S. Csaki, S. Houdkova, M. Barbosa, T. Tesar, J. Cizek, R. Musalek, O. Kovarik, T. Chraska, Improvement of mechanical properties of plasma sprayed Al2O3-ZrO2-SiO2 amorphous coatings by surface crystallization. Materials 12(19), 3232 (2019)10.3390/ma12193232 ↗
8. T. Tesar, R. Musalek, F. Lukac, J. Medricky, J. Cizek, V. Rimal, S. Joshi, T. Chraska, Increasing alpha-phase content of alumina-chromia coatings deposited by suspension plasma spraying using hybrid and intermixed concepts. Surf. Coat. Technol. 371, 298–311 (2019)10.1016/j.surfcoat.2019.04.091 ↗
9. R. Musalek, J. Matejicek, M. Vilemova, O. Kovarik, Non-linear mechanical behavior of plasma sprayed alumina under mechanical and thermal loading. J. Therm. Spray Technol. 19(1–2), 422–428 (2010)10.1007/s11666-009-9362-x ↗
10. T. Tesar, R. Musalek, J. Medricky, J. Kotlan, F. Lukac, Z. Pala, P. Ctibor, T. Chraska, S. Houdkova, V. Rimal, N. Curry, Development of suspension plasma sprayed alumina coatings with high enthalpy plasma torch. Surf. Coat. Technol. 325, 277–288 (2017)10.1016/j.surfcoat.2017.06.039 ↗
11. O. Tingaud, A. Grimaud, A. Denoirjean, G. Montavon, V. Rat, J.F. Coudert, P. Fauchais, T. Chartier, Suspension plasma-sprayed alumina coating structures: operating parameters versus coating architecture. J. Therm. Spray Technol. 17(5–6), 662–670 (2008)10.1007/s11666-008-9218-9 ↗
12. S. Goel, S. Bjorklund, N. Curry, U. Wiklund, S.V. Joshi, Axial suspension plasma spraying of Al2O3 coatings for superior tribological properties. Surf. Coat. Technol. 315, 80–87 (2017)10.1016/j.surfcoat.2017.02.025 ↗
13. R. Rampon, O. Marchand, C. Filiatre, G. Bertrand, Influence of suspension characteristics on coatings microstructure obtained by suspension plasma spraying. Surf. Coat. Technol. 202(18), 4337–4342 (2008)10.1016/j.surfcoat.2008.04.006 ↗
14. P. Sokolowski, S. Kozerski, L. Pawlowski, A. Ambroziak, The key process parameters influencing formation of columnar microstructure in suspension plasma sprayed zirconia coatings. Surf. Coat. Technol. 260, 97–106 (2014)10.1016/j.surfcoat.2014.08.078 ↗
15. E. Canas, M. Vicent, M.J. Orts, R. Moreno, E. Sanchez, Bioactive glass suspensions preparation for suspension plasma spraying. J. Eur. Ceram. Soc. 36(16), 4281–4290 (2016)10.1016/j.jeurceramsoc.2016.06.011 ↗
16. E. Canas, M. Vicent, M.J. Orts, E. Sanchez, Bioactive glass coatings by suspension plasma spraying from glycolether-based solvent feedstock. Surf. Coat. Technol. 318, 190–197 (2017)10.1016/j.surfcoat.2016.12.060 ↗
17. L. Altomare, D. Bellucci, G. Bolelli, B. Bonferroni, V. Cannillo, L. De Nardo, R. Gadow, A. Killinger, L. Lusvarghi, A. Sola, N. Stiegler, Microstructure and in vitro behaviour of 45S5 bioglass coatings deposited by high velocity suspension flame spraying (HVSFS). J. Mater. Sci. Mater. Med. 22(5), 1303–1319 (2011)10.1007/s10856-011-4307-6 ↗
18. A. Cattini, D. Bellucci, A. Sola, L. Pawlowski, V. Cannillo, Suspension plasma spraying of optimised functionally graded coatings of bioactive glass/hydroxyapatite. Surf. Coat. Technol. 236, 118–126 (2013)10.1016/j.surfcoat.2013.09.037 ↗
19. J. Cizek, V. Brozek, T. Chraska, F. Lukac, J. Medricky, R. Musalek, T. Tesar, F. Siska, Z. Antos, J. Cupera, M. Matejkova, Z. Spotz, S. Houdkova, M. Kverka, Silver-doped hydroxyapatite coatings deposited by suspension plasma spraying. J. Therm. Spray Technol. 27(8), 1333–1343 (2018)10.1007/s11666-018-0767-2 ↗
20. J. Cizek, O. Kovarik, F. Siska, J. Bensch, J. Cupera, M. Matejkova, J. Siegl, T. Chraska, K.A. Khor, Increasing fatigue endurance of hydroxyapatite and rutile plasma sprayed biocomponents by controlling deposition in-flight properties. ACS Biomater. Sci. Eng. 5(4), 1703–1714 (2019)10.1021/acsbiomaterials.8b01545 ↗
21. J. Heat transfer to particles in the plasma flame. In: Proceedings of the American Institute of Chemical Engineering Meeting, pp. 1–9, Los Angeles, 1962.
22. L. Pawlowski, The Science and Engineering of Thermal Spray Coatings, 2nd edn. (Wiley, NY, 2008).10.1002/9780470754085 ↗
23. M. Hrabovsky, V. Kopecky, V. Sember, T. Kavka, O. Chumak, M. Konrad, Properties of hybrid water/gas DC arc plasma torch. IEEE Trans. Plasma Sci. 34(4), 1566–1575 (2006)10.1109/TPS.2006.878365 ↗
24. H.M. Rietveld, Line profiles of neutron powder-diffraction peaks for structure refinement. Acta Cryst. 22, 151–152 (1967)10.1107/S0365110X67000234 ↗
25. X. Li, H. Gao, M.C. Soteriou, Investigation of the impact of high liquid viscosity on jet atomization in crossflow via high-fidelity simulations. Phys. Fluids 29(8), 082103 (2017)10.1063/1.4996178 ↗
26. L.P. Hsiang, G.M. Faeth, Drop deformation and breakup due to shock wave and steady disturbances. Int. J. Multiphase Flow 21(4), 545–560 (1995)10.1016/0301-9322(94)00095-2 ↗
27. J. Medricky, R. Musalek, M. Janata, T. Chraska, and F. Lukac. Cost-effective plasma spraying for large-scale applications. In: International Thermal Spray Conference, pp. 683–689, Orlando, 201810.31399/asm.cp.itsc2018p0683 ↗
28. G. Bolelli, V. Cannillo, R. Gadow, A. Killinger, L. Lusvarghi, T. Manfredini, P. Muller, Properties of Al2O3 coatings by high velocity suspension flame spraying (HVSFS): effects of injection systems and torch design. Surf. Coat. Technol. 270, 175–189 (2015)10.1016/j.surfcoat.2015.03.005 ↗
29. T. Tesar, R. Musalek, J. Medricky, J. Cizek, On growth of suspension plasma-sprayed coatings deposited by high-enthalpy plasma torch. Surf. Coat. Technol. 371, 333–343 (2019)10.1016/j.surfcoat.2019.01.084 ↗
30. P. Chraska, J. Dubsky, K. Neufuss, J. Pisacka, Alumina-base plasma-sprayed materials part i: phase stability of alumina and alumina-chromia. J. Therm. Spray Technol. 6(3), 320–326 (1997)10.1007/s11666-997-0066-9 ↗
31. O. Tingaud, P. Bertrand, G. Bertrand, Microstructure and tribological behavior of suspension plasma sprayed Al2O3 and Al2O3-YSZ composite coatings. Surf. Coat. Technol. 205(4), 1004–1008 (2010)10.1016/j.surfcoat.2010.06.003 ↗
32. E. Klyatskina, E. Rayon, G. Darut, M.D. Salvador, E. Sanchez, G. Montavon, A study of the influence of TiO2 addition in Al2O3 coatings sprayed by suspension plasma spray. Surf. Coat. Technol. 278, 25–29 (2015)10.1016/j.surfcoat.2015.07.029 ↗