journal article·2019-01

Variation of Heat Input and Its Influence on Residual Stresses and Coating Properties in Arc Spraying with Different Gas Mixtures

Michél Hauer, Richard Banaschik, Werner Kroemmer, Knuth-Michael Henkel

Journal of Thermal Spray Technology· Volume 28· Issue 1-2
Publisher page

Abstract

This work is about the influence of heat input on arc-sprayed coatings, caused by varying spraying patterns. The highly cavitation erosion-resistant alloys CuAl9Ni5Fe4Mn and CuMn13Al8Fe3Ni2 were arc-sprayed with a spiral-shaped pattern, using both pressurized air and a mixture of nitrogen and hydrogen. Process temperatures were recorded by thermographic imaging, and residual stresses were measured by modified hole-drilling method. Moreover, analyses of the cavitation erosion behavior and other properties were performed. Compared to previous own works, in which a meander-shaped spray pattern was used, most importantly the thermal loads, for example the maximum temperatures, during the coating buildup were lowered up to approx. 20 °C. Moreover, a more even heating of the specimens and reduced tensile stresses for both atomizing gases and materials were achieved. Furthermore, also the course of the residual stresses was changed. Hence, the dominance of the quenching stresses regarding residual stresses and coating properties, especially when spraying with pressurized air, was found to be reduced. In addition, the cavitation erosion resistance was improved severely, i.e., erosion depth was decreased up to 57%. In contrast to the aforementioned positive effects, the deposition efficiency, Young’s moduli and hardness were reduced, but still sufficient considering the application.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Advanced materials and composites · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (26)

Show source-provided references
1. Naval Sea Systems Command and National Surface Treatment Center, Rudder Coating Failures on Navy Ships (2003). http://slideplayer.com/slide/2373629/ . Accessed 13 June 2018
2. Standard Test Method For Cavitation Erosion Using Vibratory Apparatus, G32, Annual Book of ASTM Standards, vol. 03.02 (ASTM, 2010), p 98-116
3. J. Carlton, D. Radosavljevic, and S. Whitworth, Rudder–Propeller–Hull interaction: the results of some recent research, in-service problems and their solutions, in Proceedings of the First International Symposium on Marine Propulsors—smp’09, ed. by K. Koushan and S. Steen, June 22-24, 2009 (Trondheim, Norway), MARINTEK, 2009, p 262-269
4. J. Carlton, Propeller Maintenance and Repair, Marine Propellers and Propulsion, 2nd ed., Butterworth-Heinemann, Oxford, 2007, p 511-519
5. J.-H. Kim and M.-H. Lee, A Study on Cavitation Erosion and Corrosion Behavior of Al-, Zn-, Cu-, and Fe-Based Coatings Prepared by Arc Spraying, J. Therm. Spray Technol., 2010, 19(6), p 1224-123010.1007/s11666-010-9521-0 ↗
6. F. Lang and W. Krömmer, Economic and ecological benefits of using gas mixtures for arc spraying, in Proceedings of the 10th Colloquium High Velocity Oxy-Fuel Flame Spraying, W. Krömmer, Ed., October 29-30 (Erding, Germany), Gemeinschaft Thermisches Spritzen e.V. (Association of Thermal Sprayers, 2015), p 79-88
7. GTV Verschleißschutz GmbH, Krebs Korrosionsschutz GmbH Rostock, EEW SPC GmbH, Thermal Sprayed Aluminium: A Brand-New Robot-Based Technological Innovation Coating Concept, 2017. https://www.youtube.com/watch?v=O5v73kPugm0 . Accessed 13 June 2018
8. A. Barth, Application areas of arc spraying. Presentation within the seminar “Modern Coating Technologies”, Dortmund, Germany, 5th November 2014 (in German)
9. M. Hauer, K.M. Henkel, S. Krebs, and W. Krömmer, Study of Traverse Speed Effects on Residual Stress State and Cavitation Erosion Behavior of Arc-Sprayed Aluminum Bronze Coatings, J. Therm. Spray Technol., 2017, 26(1-2), p 217-22810.1007/s11666-016-0446-0 ↗
10. M. Hauer, K.M. Henkel, S. Krebs, and W. Krömmer, Alternative Gas Mixtures in Arc Spraying: A Chance to Improve Coating Properties and Residual Stress States, J. Therm. Spray Technol., 2018, 27(1-2), p 106-11810.1007/s11666-017-0650-6 ↗
11. J. Chi, A. Zhang, S. Xie, and C. Jin, Process Optimization and Residual Stress Measurement for Arc Spraying Rapid Tooling, Acad. J. Xi’an Jiaotong Univ., 2014, 48(12), p 126-130 (in Chinese)
12. G. Jandin, H. Liao, Z.Q. Feng, and C. Coddet, Correlations Between Operating Conditions, Microstructure and Mechanical Properties of Twin Wire Arc Sprayed Steel Coatings, Mater. Sci. Eng. A, 2003, 349(1-2), p 298-30510.1016/S0921-5093(02)00767-0 ↗
13. X. Wang, J. Heberlein, E. Pfender, and W. Gerberich, Effect of Nozzle Configuration, Gas Pressure, and Gas Type on Coating Properties in Wire Arc Spray, J. Therm. Spray Technol., 1999, 8(4), p 565-57510.1361/105996399770350269 ↗
14. J. Pina, A. Dias, and J.L. Lebrun, Study by X-ray Diffraction and Mechanical Analysis of the Residual Stress Generation During Thermal Spraying, Mater. Sci. Eng. A, 2003, 347(1-2), p 21-3110.1016/S0921-5093(02)00580-4 ↗
15. S. Kuroda, T. Fukushima, and S. Kitahara, Significance of Quenching Stress in the Cohesion and Adhesion of Thermally Sprayed Coatings, J. Therm. Spray Technol., 1992, 1(4), p 325-33210.1007/BF02647160 ↗
16. S. Sampath, X.Y. Jiang, J. Matejicek, L. Prchlik, A. Kulkarni, and A. Vaidya, Role of Thermal Spray Processing Method on the Microstructure, Residual Stress and Properties of Coatings: An Integrated Study for Ni-5 wt%Al Bond Coats, Mater. Sci. Eng. A, 2004, 364(1-2), p 216-23110.1016/j.msea.2003.08.023 ↗
17. T.W. Clyne and S.C. Gill, Residual Stresses in Thermal Spray Coatings and Their Effect on Interfacial Adhesion: A Review of Recent Work, J. Therm. Spray Technol., 1996, 5(4), p 401-40810.1007/BF02645271 ↗
18. Y.X. Chen, X.B. Liang, Y. Liu, S.C. Wei, and B.S. Xu, Effect of Heat Treatment on Microstructure and Residual Stress of Wire Arc Sprayed High Carbon Steel Coating, Surf. Eng., 2010, 26(6), p 407-41210.1179/174329409X438970 ↗
19. M. Steinzig and E. Ponslet, Residual Stress Measurement Using the Hole Drilling Method and Laser Speckle Interferometry: Part I, Exp. Tech., 2003, 27(3), p 43-4610.1111/j.1747-1567.2003.tb00114.x ↗
20. G.S. Schajer and M. Steinzig, Full-Field Calculation of Hole-Drilling Residual Stresses from Electronic Speckle Pattern Interferometry Data, Exp. Mech., 2005, 45(6), p 526-53210.1007/BF02427906 ↗
21. W. Tillmann, E. Vogli, and M. Abdulgader, The Correlation Between the Coating Quality and the Moving Direction of the Twin Wire Arc Spraying Gun, J. Therm. Spray Technol., 2010, 19(1), p 409-42110.1007/s11666-009-9452-9 ↗
22. H.J. Meigh, Cast and Wrought Aluminium Bronzes: Properties, Processes and Structure, Copper Development Association/IOM Communications, London, 2000, p 3-31
23. Dr. Siebert and Kühn GmbH Co. KG, Table of Total Emissivity. https://www.sika.net/images/Documents/Table_of_Emissivity.pdf . Accessed 13 June 2018
24. H. Mathesius and W. Krömmer, Praxis des thermischen Spritzens: Anleitung für das Fachpersonal, 2nd ed., DVS Media GmbH, Düsseldorf, 2014, p 107 (in German)
25. V. Läpple, B. Drube, G. Wittke, and C. Kammer, Werkstofftechnik Maschinenbau: Theoretische Grundlagen und praktische Anwendungen, 4th ed., Verlag Europa-Lehrmittel, Haan-Gruiten, 2013, p 567 (in German)
26. G. Montavon, S. Sampath, C.C. Berndt, H. Herman, and C. Coddet, Effects of the Spray Angle on Splat Morphology During Thermal Spraying, Surf. Coat. Technol., 1997, 91(1-2), p 107-11510.1016/S0257-8972(96)03137-4 ↗