journal article·2017-01

Flame-Sprayed Y2O3 Films with Metal-EDTA Complex Using Various Cooling Agents

Keiji Komatsu, Ayumu Toyama, Tetsuo Sekiya, Tomoyuki Shirai, Atsushi Nakamura, Ikumi Toda, Shigeo Ohshio, Hiroyuki Muramatsu, Hidetoshi Saitoh

Journal of Thermal Spray Technology· Volume 26· Issue 1-2
Publisher page

Abstract

In this study, yttrium oxide (Y2O3) films were synthesized from a metal-ethylenediaminetetraacetic (metal-EDTA) complex by employing a H2-O2 combustion flame. A rotation apparatus and various cooling agents (compressed air, liquid nitrogen, and atomized purified water) were used during the synthesis to control the thermal history during film deposition. An EDTA·Y·H complex was prepared and used as the staring material for the synthesis of Y2O3 films with a flame-spraying apparatus. Although thermally extreme environments were employed during the synthesis, all of the obtained Y2O3 films showed only a few cracks and minor peeling in their microstructures. For instance, the Y2O3 film synthesized using the rotation apparatus with water atomization units exhibited a porosity of 22.8%. The maximum film’s temperature after deposition was 453 °C owing to the high heat of evaporation of water. Cooling effects of substrate by various cooling units for solidification was dominated to heat of vaporization, not to unit’s temperatures.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Catalytic Processes in Materials Science · Luminescence Properties of Advanced Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (25)

Show source-provided references
1. H. Akasaka, M. Ohto, Y. Hasebe, A. Nakamura, S. Ohshio, and H. Saitoh, Yttria Coating Synthesized by Reactive Flame Spray Process Using Y-EDTA Complex, Surf. Coat. Tech., 2012, 205, p 3877-388010.1016/j.surfcoat.2011.01.063 ↗
2. K. Komatsu, Y. Hasebe, T. Sekiya, A. Nakamura, S. Ohshio, H. Akasaka, I. Toda, and H. Saitoh, Structural Analysis of TiO2 Particles Synthesized from Ti-EDTA·NH4 Complex, Trans. GIGAKU, 2014, 2, p 02008
3. K. Komatsu, T. Tsuchiya, Y. Hasebe, T. Sekiya, Y. Hasebe, A. Toyama, A. Nakamura, H. Akasaka, and H. Saitoh, Synthesis of Metal Oxide Particles Using Reaction Route from Rare-Earth Metal-EDTA Complexes, J. Therm. Spray Tech., 2014, 23, p 885-88910.1007/s11666-014-0099-9 ↗
4. K. Komatsu, T. Sekiya, A. Toyama, Y. Hasebe, A. Nakamura, M. Noguchi, Y. Li, S. Ohshio, H. Akasaka, H. Muramatsu, and H. Saitoh, Deposition of Metal Oxide Films from Metal-EDTA Complexes by Flame Spray Technique, J. Therm. Spray Tech., 2014, 23, p 833-83810.1007/s11666-014-0104-3 ↗
5. H. Saitoh, K. Kawahara, S. Ohshio, A. Nakamura, and N. Nambu, Metal Composition of Y2O3: Eu Powder Evaluated Using Particle Analyzer, Sci. Tech. Adv. Mater., 2005, 6, p 205-20910.1016/j.stam.2004.11.015 ↗
6. K. Komatsu, S. Tsuchida, H. Maruyama, A. Nakamura, S. Ohshio, H. Akasaka, and H. Saitoh, Synthesis of a Violet Sr-Al-O: Eu2+ Phosphor Particle Using Elemental Al Diffusion, Inter. J. Appl. Ceram. Tech., 2012, 11, p 1-8
7. K. Komatsu, T. Shirai, A. Nakamura, A. Kato, S. Ohshio, N. Nambu, I. Toda, H. Muramatsu, and H. Saitoh, Synthesis and Luminescence Properties of Eu2+-Doped 8-Coordinated SrO Phosphors, Ceram. Inter., 2013, 39, p 7115-711810.1016/j.ceramint.2013.02.053 ↗
8. K. Komatsu, A. Nakamura, S. Ohshio, I. Toda, H. Muramatsu, and H. Saitoh, Optical and Structural Stability of Blue SrO: Eu2+ Phosphor, J. Solid State Chem., 2013, 204, p 186-18910.1016/j.jssc.2013.05.015 ↗
9. N. Tanaka, S. Ohshio, H. Saitoh, and K. Uematsu, Crystal Growth of Highly Oriented Zinc Oxide by Laser Deposition Technique with Metal-EDTA (Ethylene Diamine Tetra-Acetic Acid) Complexes, Jpn. J. Appl. Phys., 1998, 37, p L1165-L116810.1143/JJAP.37.L1165 ↗
10. H.M. Ansari, M.D. Rauscher, S.A. Dregia, and S.A. Akbarn, Epitaxial Pore-Free Gadolinia-Doped Ceria Thin Films on Yttria-Stabilized Zirconia by RF Magnetron Sputtering, Ceram. Int., 2013, 39, p 9749-975210.1016/j.ceramint.2013.05.014 ↗
11. P. Mechnich and W. Braue, Air Plasma-Sprayed Y2O3 Coatings for Al2O3/Al2O3 Ceramic Matrix Composites, J. Eur. Ceram. Soc., 2013, 33, p 2645-265310.1016/j.jeurceramsoc.2013.03.034 ↗
12. H. Jamalin, R. Mozafarinia, R.S. Razavi, and R.A. Pidani, Comparison of Thermal Shock Resistances of Plasma-Sprayed Nanostructured and Conventional Yttria Stabilized Zirconia Thermal Barrier Coatings, Ceram. Int., 2012, 38, p 6705-671210.1016/j.ceramint.2012.05.060 ↗
13. Z. Lu, S.-W. Myoung, H.-S. Kim, M.-S. Kim, J.-H. Lee, Y.-G. Jung, J.-C. Jang, and U. Paik, Microstructure Evolution and Interface Stability of Thermal Barrier Coatings with Vertical Type Cracks in Cyclic Thermal Exposure, J. Therm. Spray Tech., 2013, 22, p 671-67910.1007/s11666-013-9886-y ↗
14. R. Eriksson, H. Brodin, S. Johansson, L. Ostergren, and X.-H. Li, Influence of Isothermal and Cyclic Heat Treatments on the Adhesion of Plasma Sprayed Thermal Barrier Coatings, Surf. Coat. Tech., 2011, 205, p 5422-542910.1016/j.surfcoat.2011.06.007 ↗
15. T. Tong, J. Li, Q. Chen, J.P. Longtin, S. Tankiewicz, and S. Sampath, Ultrafast Laser Micromachining of Thermal Sprayed Coatings for Microheaters: Design, Fabrication and Characterization, Sens. Actuators A, 2004, 114, p 102-11110.1016/j.sna.2004.02.012 ↗
16. C.E. Leshock, J.-N. Kim, and Y.C. Shin, Plasma Enhanced Machining of Inconel 718: Modeling of Workpiece Temperature with Plasma Heating and Experimental Results, Int. J. Mach. Tools. Manuf., 2001, 41, p 877-89710.1016/S0890-6955(00)00106-1 ↗
17. M. Magnani, P.H. Suegama, N. Espallargas, S. Dosta, C.S. Fugivara, J.M. Guilemany, and A.V. Benedetti, Influence of HVOF Parameters on the Corrosion and Wear Resistance of WC-Co Coatings Sprayed on AA7050 T7, Surf. Coat. Tech., 2008, 202, p 4746-475710.1016/j.surfcoat.2008.04.055 ↗
18. W.M. Grissom and F.A. Wierum, Liquid Spray Cooling of a Heated Surface, Int. J. Heat Mass Trans., 1981, 24, p 261-27110.1016/0017-9310(81)90034-X ↗
19. Thermal Spray Technology an Introduction, Japan Thermal Spray Society, p 15 (in Japanese). http://www.jtss.or.jp/journal/youshagijyutunyumon.pdf
20. P.L. Ke, Q.M. Wang, J. Gong, C. Sun, and Y.C. Zhou, Progressive Damage During Thermal Shock Cycling of D-Gun Sprayed Thermal Barrier Coatings with Hollow Spherical ZrO2–8Y2O3, Mater. Sci. Eng. A, 2006, 435–436, p 228-236
21. A.N. Khan and J. Lu, Thermal Cyclic Behavior of Air Plasma Sprayed Thermal Barrier Coatings Sprayed on Stainless Steel Substrates, Surf. Coat. Tech., 2007, 201, p 4653-465810.1016/j.surfcoat.2006.10.022 ↗
22. E. Altuncu, E.I. KaraalI, G. Erdogan, F. Ustel, and A. Turk, The Effect of Samples Geometry and Thermal Cycling Test Type on the Thermal Shock Behaviour of Plasma Sprayed TBCs, Plasma Process. Polym., 2009, 6, p S711-S71510.1002/ppap.200931706 ↗
23. E.R. Andrievskaya, Phase Equilibria in the Refractory Oxide Systems of Zirconia, Hafnia and Yttria with Rare-Earth Oxides, J. Eur. Ceram. Soc., 2008, 28, p 2363-238810.1016/j.jeurceramsoc.2008.01.009 ↗
24. P. Zhang, A. Navrotsky, B. Guo, I. Kennedy, A.N. Clark, C. Lesher, and Q. Liu, Energetics of Cubic and Monoclinic Yttrium Oxide Polymorphs: Phase Transitions, Surface Enthalpies, and Stability at the Nanoscale, J. Phys. Chem. C, 2008, 112, p 932-93810.1021/jp7102337 ↗
25. M.P. Fard, V. Pershin, S. Chandra, and J. Mostaghimi, Splat Shapes in a Thermal Spray Coating Process: Simulations and Experiments, J. Therm. Spray Tech., 2002, 11, p 206-21710.1361/105996302770348862 ↗