In-flight Behavior and Deposition Mechanism of Copper Coating on Polyacetal Resin Substrate
Source abstract
Abstract
Low-power microwave plasma spraying of low electrical resistivity Cu coating on polyacetal has been developed for direct printing of electric wire onto resin-based material without any interlayer, and the deposition mechanism has been investigated. Deposition behavior of Cu spray particles on POM substrate during spraying was classified into three types such as embedding, splash, and rebound. In the case of rebound, molten Cu particles vaporize the substrate material and rebound from the substrate by inverse Leidenfrost phenomena. In case of embedding, molten Cu particles are embedded on the substrate by melting the substrate surface and mechanical anchoring between particle and the substrate. The sprayed coating achieved higher adhesion strength about 3.0 MPa between the coating and substrate. Also, hydrogen addition to argon working gas and use of extension tube as gas shroud enhanced the oxide reduction and achieved lowest electrical resistivity Cu coating with lowest electrical resistivity of 0.049 μΩm, which is equivalent to 35%IACS.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Copper Interconnects and Reliability · Surface Modification and Superhydrophobicity
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. K. Oba, Wiring Harnesses for Next Generation Automobiles, Fujikura Tech. Rev., 2013, 42, p 77-80
2. P. Villanueva-Rey, S. Belo, P. Quinteiro, L. Arroja, and A.C. Dias, Wiring in the Automobile Industry: Life Cycle Assessment of an Innovative Cable Solution, J. Cleaner Prod., 2018, 204, p 237-24610.1016/j.jclepro.2018.09.017 ↗
3. T. Kita and K. Sato, Plating on Polyacetal, Plat. Surf. Finish., 1987, 74(7), p 58-63
4. M. Schlesinger and M. Paunovic, Modern Electroplating, 5th ed., Wiley, Hoboken, 201010.1002/9780470602638 ↗
5. S. Ghosh, Electroless Copper Deposition: A Critical Review, Thin Solid Films, 2019, 669, p 641-65810.1016/j.tsf.2018.11.016 ↗
6. R. Gonzalez, H. Ashrafizadeh, A. Lopera, P. Mertiny, and A. McDonald, A Review of Thermal Spray Metallization of Polymer-Based Structures, J. Therm. Spray Technol., 2016, 25(5), p 897-91910.1007/s11666-016-0415-7 ↗
7. K. Bobzin, M. Öte, M.A. Knoch, X. Liao, Ch Hopmann, and P. Ochotta, Transfer of Wire Arc-Sprayed Metal Coatings onto Plastic Parts, J. Therm. Spray Technol., 2018, 27(1–2), p 119-13410.1007/s11666-017-0667-x ↗
8. S. Tailor, A. Modi, and S.C. Modi, Thermally Sprayed Thin Copper Coatings by W-HVOF, J. Therm. Spray Technol., 2019, 28(1–2), p 273-28210.1007/s11666-018-0770-7 ↗
9. A. Ganesan, M. Yamada, and M. Fukumoto, The Effect of CFRP Surface Treatment on the Splat Morphology and Coating Adhesion Strength, J. Therm. Spray Technol., 2014, 23(1–2), p 236-24410.1007/s11666-013-0003-z ↗
10. J.A. Gan and C.C. Berndt, Review on the Oxidation of Metallic Thermal Sprayed Coatings: A Case Study with Reference to Rare-Earth Permanent Magnetic Coatings, J. Therm. Spray Technol., 2013, 22(7), p 1069-109110.1007/s11666-013-9955-2 ↗
11. S.-W. Ha, J. Mayer, B. Koch, and E. Wintermantel, Plasma-sprayed Hydroxylapatite Coating on Carbon Fibre Reinforced Thermoplastic Composite Materials, J. Mater. Sci. Mater. Med., 1994, 5(6–7), p 481-48410.1007/BF00058987 ↗
12. A. Ganesan, J. Affi, M. Yamada, and M. Fukumoto, Bonding Behavior Studies of Cold Sprayed Copper Coating on the PVC Polymer Substrate, Surf. Coat. Technol., 2012, 207, p 262-26910.1016/j.surfcoat.2012.06.086 ↗
13. A. Ganesan, M. Yamada, and M. Fukumoto, Cold Spray Coating Deposition Mechanism on the Thermoplastic and Thermosetting Polymer Substrates, J. Therm. Spray Technol., 2013, 22(8), p 1275-128210.1007/s11666-013-9984-x ↗
14. T. Yasui, D. Yamaguchi, Y. Kimura, and M. Fukumoto, Application of Atmospheric Pressure Microwave Discharge to Plasma Spray, Ind. Appl. Plasma Process, 2009, 2, p 1-7
15. A. Redza, T. Yasui, and M. Fukumoto, Deposition of Hard Chrome Coating onto Heat Susceptible Substrates by Low Power Microwave Plasma Spray, IOP Conf. Ser. Mater. Sci. Eng., 2016, 114(012030), p 1-9
16. T. Yasui, K. Tsujimoto, and M. Fukumoto, in Low Power Plasma Spraying Using Atmospheric Pressure Microwave Plasma, Proceedings 3rd Asian Thermal Spray Conference, 2008
17. T. Yasui, A. Redza, M. Fukumoto, in Development of Low Power Plasma Spray Process Using Atmospheric Pressure Microwave Plasma, Thermal Spray 2013: Proc. International Thermal Spray Conference, ed. by R.S. Lima, A. Agarwal, M.M. Hyland, Y.-C. Lau, G. Mauer, A. McDonald, F.-L. Toma, Ed., May 13–15, 2013 (Busan, Republic of Korea), ASM International, 2013, p 433–43410.31399/asm.cp.itsc2013p0433 ↗
18. A. Redza, T. Yasui, and M. Fukumoto, High Anatase Rate Titanium Dioxide Coating Deposition by Low Power Microwave Plasma Spray, IOP Conf. Ser. Mater. Sci. Eng., 2016, 114(012031), p 1-10
19. S. Tajima, S. Tsuchiya, M. Matsumori, S. Nakatsuka, and T. Ichiki, High-rate Reduction of Copper Oxide Using Atmospheric-pressure Inductively Coupled Plasma Microjets, Thin Solid Films, 2011, 519(20), p 6773-677710.1016/j.tsf.2011.01.219 ↗
20. M.B. Heaney, Electrical conductivity and resistivity, Electrical Measurement, Signal Processing, and Displays, 1st ed., J.G. Webster, Ed., CRC Press, Boca Raton, 2004, p P7-1-P7-14
21. C.W. Kang, H.W. Ng, and S.C.M. Yu, Imaging Diagnostics Study on Obliquely Impacting Plasma-Sprayed Particles Near to the Substrate, J. Therm. Spray Technol., 2006, 15(1), p 118-13010.1361/105996306X92686 ↗
22. M. Fukumoto, E. Nishioka, and T. Matsubara, Flattening and Solidification Behavior of a Metal Droplet on a Flat Substrate Surface Held at Various Temperatures, Surf. Coat. Technol., 1999, 120–121(2–3), p 131-13710.1016/S0257-8972(99)00349-7 ↗
23. M. Fukumoto, E. Nishioka, and T. Matsubara, Effect of Interface Wetting on Flattening of Freely Fallen Metal Droplet onto Flat Substrate Surface, J. Therm. Spray Technol., 2002, 11(1), p 69-7410.1361/105996302770348998 ↗
24. M. Fukumoto, E. Nishioka, and T. Nishiyama, New Criterion for Splashing in Flattening of Thermal Sprayed Particles onto Flat Substrate Surface, Surf. Coat. Technol., 2002, 161(2–3), p 103-11010.1016/S0257-8972(02)00471-1 ↗
25. P. Fauchais, M. Fukumoto, A. Vardelle, and M. Vardelle, Knowledge Concerning Splat Formation: An Invited Review, J. Therm. Spray Technol., 2004, 13(3), p 337-36010.1361/10599630419670 ↗
26. M. Fukumoto, I. Ohgitani, and T. Yasui, Effect of Substrate Surface Change on Flattening Behaviour of Thermal Sprayed Particles, Mater. Trans., 2004, 45(6), p 1869-187310.2320/matertrans.45.1869 ↗
27. M. Fukumoto, K. Yang, K. Tanaka, T. Usami, T. Yasui, and M. Yamada, Effect of Substrate Temperature and Ambient Pressure on Heat Transfer at Interface between Molten Droplet and Substrate Surface, J. Therm. Spray Technol., 2011, 20(1–2), p 48-5810.1007/s11666-010-9537-5 ↗
28. K. Yang, Y. Ebisuno, K. Tanaka, M. Fukumoto, T. Yasui, and M. Yamada, Verification of the Flattening Behavior of Thermal-sprayed Particles and Free-falling Droplets through Controlling Ambient Pressure, Surf. Coat. Technol., 2011, 205(2–3), p 3816-382310.1016/j.surfcoat.2011.01.049 ↗
29. S. Nishio and M. Hirata, Study on the Leidenfrost Temperature: 2nd Report, Behavior of Liquid-Solid Contact Surface and Leidenfrost Temperature, Trans. Jpn. Soc. Mech. Eng., 1978, 44(380), p 1335-1346 (in Japanese)10.1299/kikai1938.44.1335 ↗
30. V. Bertola, An Experimental Study of Bouncing Leidenfrost Drops: Comparison between Newtonian and Viscoelastic Liquids, Int. J. Heat Mass Transfer, 2009, 52(7–8), p 1786-179310.1016/j.ijheatmasstransfer.2008.09.028 ↗
31. G. Liang and I. Mudawar, Review of Drop Impact on Heated Walls, Int. J. Heat Mass Transfer, 2017, 106, p 103-12610.1016/j.ijheatmasstransfer.2016.10.031 ↗
32. R.S. Hall, S.J. Board, A.J. Clare, R.B. Duffey, T.S. Playle, and D.H. Poole, Inverse Leidenfrost Phenomenon, Nature, 1969, 224, p 266-26710.1038/224266a0 ↗