journal article·2017-10

Assessing Reliability of Cold Spray Sputter Targets in Photovoltaic Manufacturing

Kedar Hardikar, Johannes Vlcek, Venkata Bheemreddy, Daniel Juliano

Publisher page

Abstract

Cold spray has been used to manufacture more than 800 Cu-In-Ga (CIG) sputter targets for deposition of high-efficiency photovoltaic thin films. It is a preferred technique since it enables high deposit purity and transfer of non-equilibrium alloy states to the target material. In this work, an integrated approach to reliability assessment of such targets with deposit weight in excess of 50 lb. is undertaken, involving thermal-mechanical characterization of the material in as-deposited condition, characterization of the interface adhesion on cylindrical substrate in as-deposited condition, and developing means to assess target integrity under thermal-mechanical loads during the physical vapor deposition (PVD) sputtering process. Mechanical characterization of cold spray deposited CIG alloy is accomplished through the use of indentation testing and adaptation of Brazilian disk test. A custom lever test was developed to characterize adhesion along the cylindrical interface between the CIG deposit and cylindrical substrate, overcoming limitations of current standards. A cohesive zone model for crack initiation and propagation at the deposit interface is developed and validated using the lever test and later used to simulate the potential catastrophic target failure in the PVD process. It is shown that this approach enables reliability assessment of sputter targets and improves robustness.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Material Properties and Applications · High Temperature Alloys and Creep

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. N. Mackie, R. Tas, J. Corson and A. Bayman, A different Approach: CIGS using all pvd, in 28th European PV Solar Energy Conference, Paris, 2013
2. J. Vlcek, K. Hardikar, and D. Juliano, A Method for Mechanical Characterization of Cold Spray Sputter Targets in PV Manufacturing, J. Therm. Spray Technol., 2015, 7, p 881-887
3. W. Han, X. Meng, J. Zhang, and J. Zhao, Elastic Modulus of 304 Stainless Steel Coating by Cold Gas Dynamic Spraying, J. Iron. Steel Res. Int., 2012, 19, p 73-7810.1016/S1006-706X(12)60077-6 ↗
4. A. Ang and C. Berndt, A Review of Testing Methods for Thermal Spray Coatings, Int. Mater. Rev., 2014, 59, p 179-22310.1179/1743280414Y.0000000029 ↗
5. H. Kim and Y. Kweon, Elastic Modulus of Plasma-Sprayed Coatings Determined by Indentation and Bend Tests, Thin Solid Films, 1999, 342, p 201-20610.1016/S0040-6090(98)01491-6 ↗
6. R. Musalek, J. Matejicek, M. Vilemova, and O. Kovarik, Non-linear Mechanical Behavior of Plasma Sprayed Alumina Under Mechanical and Thermal Loading, J. Therm. Spray Technol., 2010, 19, p 422-42810.1007/s11666-009-9362-x ↗
7. D. Goldbaum, J. Ajaja, R. Chromik, W. Wong, S. Yue, E. Irissou, and J. Legoux, Mechanical Behavior of Ti Cold Spray Coatings Determined by Multiscale Indentation Method, Mater. Sci. Eng., A, 2011, 530, p 253-26510.1016/j.msea.2011.09.083 ↗
8. A. Bacciochini, M. Radulescu, M. Yandouzi, G. Maines, J. Lee, and B. Jodoin, Reactive Structural Materials Consolidated by Cold Spray: Al-CuO Thermite, Surf. Coat. Technol., 2013, 226, p 60-6710.1016/j.surfcoat.2013.03.036 ↗
9. Y.T. Cheng and C.M. Cheng, Can Stress–Strain Relationships be Obtained From Indentation Curves Using Conical and Pyramidal Indenters?, J. Mater. Res., 1999, 14, p 3493-349610.1557/JMR.1999.0472 ↗
10. S.G. Croll, C. Siripirom, and B.D. Keil, “Pull-Off Adhesion Test for Coatings on Large Pipes: Possible Variations in Failure Location and Mode”, Pipelines, ASCE, 2014, 2014, p 1319-1333
11. B. Duncan and L. Crocker, Review of Tests for Adhesion Strength, NPL Report MATC(A)67, 2001, p 1-35
12. ASTM D3433, Standard Test Method for Fracture Strength in Cleavage of Adhesives in Bonded Metal Joints, ASTM, 2012. doi: 10.1520/D3433-99R1210.1520/D3433-99R12 ↗
13. ASTM D5528, Standard Test Method for Mode I Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites, ASTM, 2013. doi: 10.1520/D5528-1310.1520/D5528-13 ↗
14. J.G. Ratcliffe, Sizing Single Cantilever Beam Specimens for Characterizing Facesheet/Core Peel Debonding in Sandwich Structure, in 9th International Conference on Sandwich Structures, Pasadena, California, 2010
15. A. Needleman, A Continuum Model for Void Nucleation by Inclusion Debonding, J. Appl. Mech., 1987, 54, p 525-53110.1115/1.3173064 ↗
16. T. Diehl, Modeling Surface-Bonded Structures with ABAQUS Cohesive Elements: Beam-Type Solutions, in ABAQUS Users’ Conference, 2005
17. G. Ji, Z. Ouyang, G. Li, S. Ibekwe, and S. Pang, Effects of Adhesive Thickness on Global and Local Mode-I, Interfacial Fracture of Bonded Joints, Int. J. Solids Struct., 2010, 47, p 2445-245810.1016/j.ijsolstr.2010.05.006 ↗
18. K. Park and G.H. Paulino, Cohesive Zone Models: a Critical Review of Traction–Separation Relationships Across Fracture Surfaces, Appl. Mech. Rev., 2013, 64, p 06080210.1115/1.4023110 ↗
19. C. Wu, S. Gowrishankar, R. Huang, and K. Liechti, On Determining Mixed-Mode Traction–Separation Relations for Interfaces, Int. J. Fract., 2016, 202, p 1-910.1007/s10704-016-0128-4 ↗
20. C. Di Leo, J. Luk-Cyr, H. Liu, K. Loeffel, K. Al-Athel, and L. Anand, A New Methodology for Characterizing Traction–Separation Relations for Interfacial Delamination of Thermal Barrier Coatings, Acta Mater., 2014, 71, p 306-31810.1016/j.actamat.2014.02.034 ↗
21. W. Zhu, L. Yang, J. Guo, Y. Zhou, and C. Lu, Determination of Interfacial Adhesion Energies of Thermal Barrier Coatings by Compression Test Combined with a Cohesive Zone Finite Element Model, Int. J. Plast, 2015, 64, p 76-8710.1016/j.ijplas.2014.08.003 ↗
22. X. Li, L. Liang, J. Xie, L. Chen, and Y. Wei, Thickness-Dependent Fracture Characteristics of Ceramic Coatings Bonded on the Alloy Substrates, Surf. Coat. Technol., 2014, 258, p 1039-104710.1016/j.surfcoat.2014.07.031 ↗
23. ABAQUS V6.16 User’s Manual, Hibbit, Karlsson and Sorensen, Inc., Rhode Island, USA, 2016