journal article·2025-02

Thermomechanical Deformation Response in Cold Sprayed SiCp/Al Composites: Strengthening, Microstructure Characterization and Thermomechanical Properties

L. Gyansah, Tianying Xiong, Raffaella Sesana

Publisher page

Abstract

SiCp/pure Al composites with different SiCp fractions (20, 30 and 40 wt.%) were cold sprayed followed by hot axial-compression tests at deformation temperatures of 473 K (200 °C) to 673 K (400 °C), leading to failure of specimens through routine crack propagation in their multiphase. The plastic deformation behavior of the coating with respect to the SiCp contents and the deformation temperatures were studied at strain rate 1 s-1. As-sprayed and post-failure specimens were analyzed by x-ray computed tomography (XCT), transmission electron microscopy (TEM) and scanning electron microscopy (SEM). Quasi-static thermomechanical testing results revealed that compressive strength (UCS = 228 MPa) was the highest in the deposits that were compressed at 473 K compared to those of the as-sprayed, while the as-sprayed exhibited a compressive strength of 182.8 MPa related to the increment in SiCp fractions. Strength-plasticity synergy was promoted by dynamic recrystallization (DRX) through strengthening and refinement of the grains. The DRX degree depends relevantly on grain refinement, higher deformation temperature and the pinning effects of the interfaces promoted by the ultrafine grain structures (UFG). Reconstructed XCT data revealed different crack propagation mechanisms. A single-plane shear crack with multilaminates fracture morphology yields relatively through the as-sprayed and as-deformed at 473 K deposits, while a multiphase plane shear cracks preeminently existed in high temperature deformed deposits resulting in multiphase-interface delaminations. Three pertinent strengthening mechanisms, videlicet, SiCp dispersed strengthening, refined grain strengthening and dislocation strengthening existed in the gradient microstructure, and their detailed contributions to the thermomechanical properties were discussed.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · High-Temperature Coating Behaviors · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (43)

Show source-provided references
1. X. Li et al., Hot Deformation Behaviour of SiC/AA6061 Composites Prepared by Spark Plasma Sintering, J. Mater. Sci. Technol., 2016, 32(4), p 291-297.10.1016/j.jmst.2015.12.006 ↗
2. L. Gyansah et al., Cold Spraying SiC/Al Metal Matrix Composites: Effects of SiC Contents and Heat Treatment on Microstructure, Thermophysical and Flexural Properties, Mater. Res. Express, 2018, 5(2), 026523.10.1088/2053-1591/aaaeee ↗
3. S. Venkatesan and M.A. Xavior, Analysis of Mechanical Properties of Aluminum Alloy Metal Matrix Composite by Squeeze Casting—A Review, Mater. Today Proc., 2018, 5(5), p 11175-11184.10.1016/j.matpr.2018.01.141 ↗
4. Y. Bai et al., Corrosion Behavior of Low Pressure Cold Sprayed Zn-Ni Composite Coatings, J. Alloy. Compd., 2017, 719, p 194-202.10.1016/j.jallcom.2017.05.134 ↗
5. S. Kumar, S.K. Reddy, and S.V. Joshi, Microstructure and Performance of Cold Sprayed Al-SiC Composite Coatings with High Fraction Of Particulates, Surf. Coat. Technol., 2017, 318, p 62-71.10.1016/j.surfcoat.2016.11.047 ↗
6. P. Rodrigo et al., Microstructure and Wear Resistance of Al-SiC Composites Coatings on ZE41 Magnesium Alloy, Appl. Surf. Sci., 2009, 255(22), p 9174-9181.10.1016/j.apsusc.2009.06.122 ↗
7. J. Michael Shockley et al., Significance of Al2O3 Particle Morphology in the Microstructure Evolution of Cold-Sprayed Al-Al2O3 During Unconstrained High-Pressure Torsion, Mater. Sci. Eng. A, 2017, 684, p 510-516.10.1016/j.msea.2016.12.078 ↗
8. D. Garbiec et al., Properties of Al-Al2O3 Composites Synthesized by Spark Plasma Sintering Method, Arch. Civ. Mech. Eng., 2015, 15(4), p 933-939.10.1016/j.acme.2015.02.004 ↗
9. V. Auradi, G.L. Rajesh, and S.A. Kori, Processing of B4C Particulate Reinforced 6061Aluminum Matrix Composites by Melt Stirring Involving Two-step Addition, Proc. Mater. Sci., 2014, 6, p 1068-1076.10.1016/j.mspro.2014.07.177 ↗
10. C. Cui et al., Plastic-Deformation-Driven SiC Nanoparticle Implantation in an Al Surface by Laser Shock Wave: Mechanical Properties, Microstructure Characteristics, and Synergistic Strengthening Mechanisms, Int. J. Plast., 2018, 102, p 83-100.10.1016/j.ijplas.2017.12.004 ↗
11. R.N. Raoelison, C. Verdy, and H. Liao, Cold Gas Dynamic Spray Additive Manufacturing Today: Deposit Possibilities, Technological Solutions and Viable Applications, Mater. Des., 2017, 133, p 266-287.10.1016/j.matdes.2017.07.067 ↗
12. F. Khodabakhshi et al., Interfacial Bonding Mechanisms Between Aluminum and Titanium During Cold Gas Spraying Followed by Friction-Stir Modification, Appl. Surf. Sci., 2018, 462, p 739-752.10.1016/j.apsusc.2018.08.156 ↗
13. S. Siegmann and C. Abert, 100 Years of Thermal Spray: About the Inventor Max Ulrich Schoop, Surf. Coat. Technol., 2013, 220, p 3-13.10.1016/j.surfcoat.2012.10.034 ↗
14. R. Gostariani et al., Fabrication of Al/AlN In-situ Nanocomposite Through Planetary Ball Milling and Hot Extrusion of Al/BN: Microstructural Evaluation and Mechanical Behavior, J. Alloy. Compd., 2018, 768, p 329-339.10.1016/j.jallcom.2018.07.256 ↗
15. Y. Fu et al., Fabrication of Nanodiamond Reinforced Aluminum Composite Coatings by Flame Spraying for Marine Applications, Mater. Today Commun., 2018, 17, p 46-52.10.1016/j.mtcomm.2018.08.010 ↗
16. W. Li et al., A Review of Advanced Composite and Nanostructured Coatings by Solid-State Cold Spraying Process, Crit. Rev. Solid State Mater. Sci., 2018, 44, p 109-156.10.1080/10408436.2017.1410778 ↗
17. R. Nikbakht et al., Asymmetrical Bonding in Cold Spraying of Dissimilar Materials, Appl. Surf. Sci., 2018, 444, p 621-632.10.1016/j.apsusc.2018.03.103 ↗
18. Y. Xie et al., New Insights into the Coating/Substrate Interfacial Bonding Mechanism in Cold Spray, Scr. Mater., 2016, 125, p 1-4.10.1016/j.scriptamat.2016.07.024 ↗
19. M. Grujicic et al., Adiabatic Shear Instability Based Mechanism for Particles/Substrate Bonding in the Cold-Gas Dynamic-Spray Process, Mater. Des., 2004, 25(8), p 681-688.10.1016/j.matdes.2004.03.008 ↗
20. Y. Wang et al., Effects of Ceramic Particle Size on Microstructure and the Corrosion Behavior of Cold Sprayed SiCp/Al 5056 Composite Coatings, Surf. Coat. Technol., 2017, 315, p 314-325.10.1016/j.surfcoat.2017.02.047 ↗
21. X. Qiu et al., Microstructure, Microhardness and Tribological Behavior of Al2O3 Reinforced A380 Aluminum Alloy Composite Coatings Prepared by Cold Spray Technique, Surf. Coat. Technol., 2018, 350, p 391-400.10.1016/j.surfcoat.2018.07.039 ↗
22. D. Cong et al., Wear Behavior of cOrroded Al-Al2O3 Composite Coatings Prepared by Cold Spray, Surf. Coat. Technol., 2017, 326, p 247-254.10.1016/j.surfcoat.2017.07.063 ↗
23. N.H. Tariq et al., Cold Spray Additive Manufacturing: A Viable Strategy to Fabricate Thick B4C/Al Composite Coatings for Neutron Shielding Applications, Surf. Coat. Technol., 2018, 339, p 224-236.10.1016/j.surfcoat.2018.02.007 ↗
24. M. Yandouzi et al., Microstructure and Mechanical Properties of B4C Reinforced Al-Based Matrix Composite Coatings Deposited by CGDS and PGDS Processes, Surf. Coat. Technol., 2010, 205(7), p 2234-2246.10.1016/j.surfcoat.2010.08.143 ↗
25. L. Gyansah et al., Cold Sprayed Additive Manufacturing of SiC/Al Metal Matrix Composite: Synthesis, Microstructure, Heat Treatment and Tensile Properties, Mater. Sci. Forum, 2018, 932, p 62-75.10.4028/www.scientific.net/MSF.932.62 ↗
26. T. Guo et al., Microstructure and Properties of Bulk Al0.5CoCrFeNi High-Entropy Alloy by Cold Rolling and Subsequent Annealing, Mater. Sci. Eng. A, 2018, 729, p 141-148.10.1016/j.msea.2018.05.054 ↗
27. H. Berns, Heat Treatment, Ferrous Materials: Steel and Cast Iron. H. Berns, W. Theisen Ed., Springer, Berlin, 2008, p 55-7610.1007/978-3-540-71848-2_3 ↗
28. Y.C. Lin et al., EBSD Study of a Hot Deformed Nickel-Based Superalloy, J. Alloy. Compd., 2015, 640, p 101-113.10.1016/j.jallcom.2015.04.008 ↗
29. J.F. Engelberger, Heat Treatment Applications, Robotics in Practice: Management and Applications of Industrial Robots. J.F. Engelberger Ed., Springer, Boston, 1980, p 247-25210.1007/978-1-4684-7120-5_20 ↗
30. H. Daoguang et al., Microstructural Evolution and Support Vector Regression Model for an Aged Ni-Based Superalloy During Two-Stage Hot Forming with Stepped Strain Rates, Mater. Des., 2018, 154, p 51-62.10.1016/j.matdes.2018.05.022 ↗
31. X.-M. Chen et al., Dynamic Recrystallization Behavior of a Typical Nickel-Based Superalloy During Hot Deformation, Mater. Des., 2014, 57, p 568-577.10.1016/j.matdes.2013.12.072 ↗
32. H. Assadi et al., Cold Spraying—A Materials Perspective, Acta Mater., 2016, 116, p 382-407.10.1016/j.actamat.2016.06.034 ↗
33. W. Li et al., Solid-State Additive Manufacturing and Repairing by Cold Spraying: A Review, J. Mater. Sci. Technol., 2018, 34(3), p 440-457.10.1016/j.jmst.2017.09.015 ↗
34. Q. Hu, H. Zhao, and F. Li, Microstructures and Properties of SiC Particles Reinforced Aluminum-Matrix Composites Fabricated by Vacuum-Assisted High Pressure Die Casting, Mater. Sci. Eng. A, 2017, 680, p 270-277.10.1016/j.msea.2016.10.090 ↗
35. R. Rajeshkumar et al., Microstructural Evolution in Ultrafine Grained Al-Graphite Composite Synthesized Via Combined Use of Ultrasonic Treatment and Friction Stir Processing, J. Alloy. Compd., 2017, 726, p 358-366.10.1016/j.jallcom.2017.07.280 ↗
36. R. Dong et al., High Content SiC Nanowires Reinforced Al Composite with High Strength and Plasticity, Mater. Sci. Eng. A, 2015, 630, p 8-12.10.1016/j.msea.2015.02.013 ↗
37. R.N. Raoelison et al., Cold Gas Dynamic Spray Technology: A Comprehensive Review of Processing Conditions for Various Technological Developments Till to Date, Addit. Manuf., 2018, 19, p 134-159.
38. K. Kang et al., Formation and Heat Treatment of Kinetic Sprayed Nanocrystalline Al Coatings Reinforced with Multi-walled Carbon Nanotubes: The Relationship Between Microstructural Features and Physical Properties, Surf. Coat. Technol., 2016, 289, p 124-135.10.1016/j.surfcoat.2016.01.030 ↗
39. P. Papanastasiou and D. Durban, Singular Crack-Tip Plastic Fields in Tresca and Mohr-Coulomb Solids, Int. J. Solids Struct., 2018, 136-137, p 250-258.10.1016/j.ijsolstr.2017.12.018 ↗
40. A. Moridi et al., Cold Spray Coating: Review of Material Systems and Future Perspectives, Surf. Eng., 2014, 30, p 369-395.10.1179/1743294414Y.0000000270 ↗
41. S.M. Hassani-Gangaraj et al., Experimental Assessment and Simulation of Surface Nanocrystallization by Severe Shot Peening, Acta Mater., 2015, 97, p 105-115.10.1016/j.actamat.2015.06.054 ↗
42. S. Wulfinghoff and T. Böhlke, Gradient Crystal Plasticity Including Dislocation-Based Work-Hardening and Dislocation Transport, Int. J. Plast., 2015, 69, p 152-169.10.1016/j.ijplas.2014.12.003 ↗
43. A. Sanaty-Zadeh, Comparison Between Current Models for the Strength of Particulate-Reinforced Metal Matrix Nanocomposites with Emphasis on Consideration of Hall-Petch Effect, Mater. Sci. Eng. A, 2012, 531, p 112-118.10.1016/j.msea.2011.10.043 ↗