Effect of (Thermo-) Mechanical Post-Treatments on Material Properties of Cold-Sprayed Inconel®625 Coatings
Source abstract
Abstract
Abstract Cold spraying of high strength materials, i.e., Inconel ® 625, is challenging due to restricted deformability and thus high critical velocity to achieve bonding. This affects the reachable extent of well-bonded areas and therefore tensile strength. Hence, further process optimization and/or post-treatments are needed to reach deposit qualities with low porosity and sufficient strength. In this study, two (thermo-) mechanical post-treatments are used for modification of deposit properties; Laser Shock Peening (LSP) to close internal porosities and to heal out non-bonded interfaces by induced compressive shock waves and Surface Rolling (SR) for further deposit densification, work hardening and surface smoothing. These treatments are associated with compressive residual stresses. Compressive residual stresses, resulting using LSP as post-treatment reached to − 540 MPa in 0.15 mm and − 450 MPa in 0.10 mm depth underneath the top surface for deposits produced with small η = 0.95 and high η = 1.11 correspondingly. The induced compressive stresses decrease with increasing distance to surface and reach a depth of up to 300 µm. For deposits processed with high- and low- η values, LSP reduces deposit porosities by 37% and 34%, respectively. The results demonstrate that Surface Rolling can be used to decrease porosities from 0.16% in as-sprayed condition to 0.01% after SR. Surface Rolling the deposits reduced their surface roughness by up to 95% (from Rz = 31.28 µm to Rz = 1.45 µm) and increased the microhardness by about 4%. The obtained benefits of SR are mainly due to the severe deformation and build-up of compressive residual stresses within a depth of up to 200 µm beneath the top surface. In summary, LSP proves to be an effective tool to further enhance the quality of Inconel ® 625 cold-sprayed deposits and in view of applications, Surface Rolling can be used to tailor deposit qualities, as well.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Erosion and Abrasive Machining · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (36)
Show source-provided references
1. F. Taherkhani, A. List, S. Keller, N. Kashaev, F. Gärtner, and T. Klassen, The Influence of Spraying Parameters and Powder Sizes on the Microstructure and Mechanical Behavior of Cold-Sprayed Inconel®625 Deposits, J. Therm. Spray Tech., 2024, 33, p 652–665. https://doi.org/10.1007/s11666-024-01712-810.1007/s11666-024-01712-8 ↗
2. D. Shrestha, F. Azarmi, and X.W. Tangpong, Effect of Heat Treatment on Residual Stress of Cold Sprayed Nickel-Based Superalloys, J. Therm. Spray Technol., 2022, 31, p 197–205. https://doi.org/10.1007/s11666-021-01284-x10.1007/s11666-021-01284-x ↗
3. K. Wu, W. Sun, A.W.-Y. Tan, I. Marinescu, E. Liu, and W. Zhou, An Investigation Into Microstructure, Tribological and Mechanical Properties of Cold Sprayed Inconel 625 Coatings, Surf. Coat. Technol., 2021, 424, p 127660. https://doi.org/10.1016/j.surfcoat.2021.12766010.1016/j.surfcoat.2021.127660 ↗
4. R.G. Neo, K. Wu, S.C. Tan, and W. Zhou, Effect of Spray Distance and Powder Feed Rate on Particle Velocity in Cold Spray Processes, Metals, 2022, 12(1), p 75. https://doi.org/10.3390/met1201007510.3390/met12010075 ↗
5. T. Klassen, F. Gärtner, H. Assadi (2016) Process science of cold spray, in High Pressure Cold Spray by Charles M. Kay, J. Karthikeyan (eds.), ASM International, p. 17–6510.31399/asm.tb.hpcspa.t54460017 ↗
6. F. Taherkhani, S. Keller, N. Kashaev, F. Gärtner, T. Klassen, Cold spraying of inconel 625 thick deposits. In: Thermal Spray 2023: Proceedings from the international thermal spray conference. ITSC 2023. Québec City, Canada, 2023: ASM International (International Thermal Spray Conference), p. 266–27210.31399/asm.cp.itsc2023p0266 ↗
7. P. Cavaliere, A. Perrone, and A. Silvello, Fatigue Behavior of Inconel 625 Cold Spray Coatings, Surf. Eng., 2018, 34(5), p 380–391. https://doi.org/10.1080/02670844.2017.137187210.1080/02670844.2017.1371872 ↗
8. N. Kashaev, V. Ventzke, M. Horstmann, S. Chupakhin, S. Riekehr, R. Falck, E. Maawad, P. Staron, N. Schell, and N. Huber, Effects of Laser Shock Peening on the Microstructure and Fatigue Crack Propagation Behaviour of Thin Aa2024 Specimens, Int. J. Fatigue, 2017, 98, p 223–233. https://doi.org/10.1016/j.ijfatigue.2017.01.04210.1016/j.ijfatigue.2017.01.042 ↗
9. Y. Tan, G. Wu, J.-M. Yang, and T. Pan, Laser Shock Peening on Fatigue Crack Growth Behavior of Aluminium Alloy, Fatigue Fract. Eng. Mater. Struct., 2004, 27(8), p 649–656. https://doi.org/10.1111/j.1460-2695.2004.00763.x10.1111/j.1460-2695.2004.00763.x ↗
10. Z. Kallien, S. Keller, V. Ventzke, N. Kashaev, and B. Klausemann, Effect of Laser Peening Process Parameters and Sequences on Residual Stress Profiles, Metals, 2019, 9(6), p 655. https://doi.org/10.3390/met906065510.3390/met9060655 ↗
11. S. Keller, M. Horstmann, N. Kashaev, and B. Klausemann, Experimentally Validated Multi-Step Simulation Strategy to Predict the Fatigue Crack Propagation Rate in Residual Stress Fields After Laser Shock Peening, Int. J. Fatigue, 2019, 124, p 265–276. https://doi.org/10.1016/j.ijfatigue.2018.12.01410.1016/j.ijfatigue.2018.12.014 ↗
12. M. Rozmus-Górnikowska, J. Kusinski, and L. Cieniek, Effect of Laser Shock Peening on the Microstructure and Properties of the Inconel 625 Surface Layer, J. Mater. Eng. Perform., 2020, 29, p 1544–1549. https://doi.org/10.1007/s11665-020-04667-310.1007/s11665-020-04667-3 ↗
13. L. Chen, P. Gu, T. Ge, Y. Sun, L. Li, and X. Ren, Effect of Laser Shock Peening on Microstructure and Mechanical Properties Of TiC Strengthened Inconel 625 Alloy Processed by Selective Laser Melting, Mater. Sci. Eng. A, 2022, 835, p 142610. https://doi.org/10.1016/j.msea.2022.14261010.1016/j.msea.2022.142610 ↗
14. K. Zhao, K. Chen, G. Jiang, X. Wang, and C. Cui, Effect of Laser Shock Peening on Surface Morphology of Cold-Sprayed Pure Aluminum Coating, Chin. J. Lasers, 2023, 50(4), p 0402004–0402004. https://doi.org/10.3788/CJL22063810.3788/CJL220638 ↗
15. A.M. Ralls, B. Mao, and P.L. Menezes, Tribological Performance of Laser Shock Peened Cold Spray Additive Manufactured 316L Stainless Steel, J. Tribol., 2023, 145(7), p 071702. https://doi.org/10.1115/1.406210210.1115/1.4062102 ↗
16. W. Niu, N. Li, and Q. Wang, Effects of Laser Shock Peening on Interfacial Bonding Strength of Cold-Sprayed Coating, J. Therm. Spray Technol., 2024, 33(6), p 1800–1814. https://doi.org/10.1007/s11666-024-01815-210.1007/s11666-024-01815-2 ↗
17. N. Maharjan, T. Ramesh, D.Q. Pham, W. Zhai, A. Ang, and W. Zhou, Post-Processing of Cold Sprayed Ti6Al4V Coating by Laser Shock Peening, J. Mater. Process. Technol., 2024, 330(6), p 118461. https://doi.org/10.1016/j.jmatprotec.2024.11846110.1016/j.jmatprotec.2024.118461 ↗
18. C. Courbon, A. Sova, F. Valiorgue, H. Pascal, J. Sijobert, G. Kermouche, Ph. Bertrand, and J. Rech, Near Surface Transformations of Stainless Steel Cold Spray and Laser Cladding Deposits After Turning and Ball-Burnishing, Surf. Coat. Technol., 2019, 371, p 235–244. https://doi.org/10.1016/j.surfcoat.2019.01.09210.1016/j.surfcoat.2019.01.092 ↗
19. V. Chomienne, F. Valiorgue, J. Rech, and C. Verdu, Influence of Ball Burnishing on Residual Stress Profile of a 15–5PH Stainless Steel, CIRP J. Manuf. Sci. Technol., 2016, 13, p 90–96. https://doi.org/10.1016/j.cirpj.2015.12.00310.1016/j.cirpj.2015.12.003 ↗
20. W. Sun, A.-Y. Tan, K. Wu, S. Yin, X. Yang, I. Marinescu, and E. Liu, Post-Process Treatments on Supersonic Cold Sprayed Coatings: a Review, Coatings, 2020, 10(2), p 123. https://doi.org/10.3390/coatings1002012310.3390/coatings10020123 ↗
21. A. Sova, C. Courbon, F. Valiorgue, J. Rech, and Ph. Bertrand, Effect of Turning and Ball Burnishing on the Microstructure and Residual Stress Distribution in Stainless Steel Cold Spray Deposits, J. Therm. Spray Technol., 2017, 26, p 1922–1934. https://doi.org/10.1007/s11666-017-0655-110.1007/s11666-017-0655-1 ↗
22. L. Berthe, R. Fabbro, P. Peyre, and E. Bartnicki, Wavelength Dependent of Laser Shockwave Generation in the Water-Confinement Regime, J. Appl. Phys., 1990, 85, p 7552–7555. https://doi.org/10.1063/1.37055310.1063/1.370553 ↗
23. B.P. Fairand, A.H. Clauer, R.G. Jung, and B.A. Wilcox, Quantitative Assessment of Laser-Induced Stress Waves Generated at Confined Surfaces, Appl. Phys. Lett., 1974, 25(8), p 431–433. https://doi.org/10.1063/1.165553610.1063/1.1655536 ↗
24. C.S. Montross, T. Wei, L. Ye, G. Clark, and Y.-W. Mai, Laser Shock Processing and its Effects on Microstructure and Properties of Metal Alloys: a Review, Int. J. Fatigue, 2002, 24(10), p 1021–1036. https://doi.org/10.1016/S0142-1123(02)00022-110.1016/S0142-1123(02)00022-1 ↗
25. L. Budde, V. Prasanthan, J. Kruse, M.Y. Faqiri, M. Lammers, J. Hermsdorf, M. Stonis, T. Hassel, B. Breidenstein, B.-A. Behrens, B. Denkena, and L. Overmeyer, Investigation of the Influence of the Forming Process and Finishing Processes on the Properties of the Surface and Subsurface of Hybrid Components, Int. J. Adv. Manuf. Technol., 2022, 119, p 119–136. https://doi.org/10.1007/s00170-021-08066-310.1007/s00170-021-08066-3 ↗
26. X. Pan, W. He, L. Zhou, S. Shu, X. Ding, Q. Wang, S. Wen, N. Li, Y. Zhu, and J. Nan, Two Laser Beam Modulation of Microstructure and Residual Stress Field in Cold Sprayed Al Alloy for Recovering Fatigue Performance, Int. J. Plast., 2023, 164, p 103598. https://doi.org/10.1016/j.ijplas.2023.10359810.1016/j.ijplas.2023.103598 ↗
27. Farrokh Taherkhani, Cold spraying of the nickel-based superalloy- Inconel®625- and properties optimization by (thermo-) mechanical-treatments, PhD dissertation, Helmut-Schmidt-University/University of the Federal Armed Forces Hamburg, Department of mechanical and civil engineering, 2024. https://doi.org/10.24405/1706010.24405/17060 ↗
28. N. Kashaev, D. Ushmaev, V. Ventzke, B. Klausemann, and F. Fomin, On the Application of Laser Shock Peening for Retardation of Surface Fatigue Cracks in Laser Beam-Welded AA6056, Fatigue Fract. Eng. Mater. Struct., 2020, 43(7), p 1500–1513. https://doi.org/10.1111/ffe.1322610.1111/ffe.13226 ↗
29. S.T. Sala, S. Keller, S. Chupakhin, D. Pöltl, B. Klausemann, and N. Kashaev, Effect of Laser Peen Forming Process Parameters on Bending and Surface Quality of Ti-6Al-4V Sheets, J. Mater. Process. Tech., 2022, 305, p 117578. https://doi.org/10.1016/j.jmatprotec.2022.11757810.1016/j.jmatprotec.2022.117578 ↗
30. A.K. Gujba and M. Medraj, Laser Peening Process and its Impact on Materials Properties in Comparison with Shot Peening and Ultrasonic Impact Peening, Materials, 2014, 7, p 7925–7974. https://doi.org/10.3390/ma712792510.3390/ma7127925 ↗
31. P.K. Dwivedi, R. Vinjamuri, A.K. Rai, P. Ganesh, K. Ranganathan, K.S. Bindra, and K. Dutta, Effect of Laser Shock Peening on Ratcheting Strain Accumulation, Fatigue Life and Bulk Texture Evolution in HSLA Steel, Int. J. Fatigue, 2022, 163, p 107033. https://doi.org/10.1016/j.ijfatigue.2022.10703310.1016/j.ijfatigue.2022.107033 ↗
32. M.B. Toparli and M.E. Fitzpatrick, Effect of Overlapping of Peen Spots on Residual Stresses in Laser-Peened Aluminium Sheets, Metall. Mater. Trans. A, 2019, 9(6), p 1109–1112. https://doi.org/10.1007/s11661-018-05100-010.1007/s11661-018-05100-0 ↗
33. H. Liu, T. L. Meng, J. Cao, C. Kiang, and I. Tan, Surface engineering and protective coating towards advanced manufacturing and remanufacturing applications, In: Proceedings of the 3rd international conference on advanced surface enhancement (INCASE), 2024. https://doi.org/10.1007/978-981-99-8643-9_4310.1007/978-981-99-8643-9_43 ↗
34. Ecoroll: Basic principles of roller burnishing, https://www.ecoroll.de/en/processes/roller-burnishing.html, updated on 12/15/2023
35. Z. Zhao, N.H. Tariq, J. Tang, C. Jia, X. Qiu, Y. Ren, H. Liu, Y. Shen, H. Du, X. Cui, J. Wang, and T. Xiong, Microstructural Evolutions and Mechanical Characteristics Of Ti/steel Clad Plates Fabricated Through Cold Spray Additive Manufacturing Followed by Hot-Rolling and Annealing, Mater. Des., 2020, 185, p 108249. https://doi.org/10.1016/j.matdes.2019.10824910.1016/j.matdes.2019.108249 ↗
36. H. K. Tönshoff, B. Denkena, Spanen. Grundlagen. 2., erweiterte und neu bearbeitete Auflage. Berlin, Heidelberg: Springer Berlin Heidelberg (VDI-Buch), 2024 Available online at https://link.springer.com/content/pdf/https://doi.org/10.1007/978-3-662-09963-6.pdf, checked on 12/15/202310.1007/978-3-662-09963-6.pdf ↗