Influential Factors on the Combustion of the Polymer Binder System in F-HVOF
Source abstract
Abstract
Abstract This study investigates the combustion dynamics and decomposition of filled thermoplastic filaments in filament high-velocity oxy-fuel spraying to improve deposition efficiency and coating quality. A quasi-steady-state combustion mechanism is proposed. Filament tip melting, fragmentation, and in-flight decomposition transform the monomodal primary powder with a mean size of 1.8 µm into a trimodal particle size distribution. Peaks occur near 500 nm, 5 µm, and 150-400 µm, with the first two likely from clean melting and decomposition, and the third from material buildup on cooled nozzle walls. Process optimizations varied the stoichiometric ratio ( λ ), feed gas flow rate, and filament diameter, and a copper insert was added to enhance filament decomposition. Coatings were prepared using PBAT filaments containing 70-80 wt.% alumina. Sub-stoichiometric flame conditions, particularly λ ≈ 0.8, gave the highest deposition efficiencies by maximizing flame temperature and promoting polymer decomposition. Reducing the feed gas flow to 5 slpm further improved efficiency, while gas composition had little effect under low flow. Filament diameter influenced efficiency by controlling feed velocity, which in turn affected the filament tip position within the nozzle. The adapted setup and optimized spraying parameters achieved a deposition efficiency of 76%, hardness of 1149 HV0.1, low porosity of 3.0%, and surface roughness values of Ra = 6.9 µm and Rz = 44.8 µm at a feed rate of 4 g/min.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Flame retardant materials and properties · Energetic Materials and Combustion · Fluid Dynamics and Heat Transfer
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (53)
Show source-provided references
1. M. Aghasibeig, F. Tarasi, R.S. Lima, A. Dolatabadi, and C. Moreau, A Review on Suspension Thermal Spray Patented Technology Evolution, J. Therm. Spray Technol., 2019, 28(7), p 1579-1605.10.1007/s11666-019-00904-x ↗
2. F.-L. Toma, A. Potthoff, L.-M. Berger, and C. Leyens, Demands, Potentials, and Economic Aspects of Thermal Spraying with Suspensions: A Critical Review, J. Therm. Spray Technol., 2015, 24(7), p 1143-1152.10.1007/s11666-015-0274-7 ↗
3. G. Mittal, and S. Paul, Suspension and Solution Precursor Plasma and HVOF Spray: A Review, J. Therm. Spray Technol., 2022, 31(5), p 1443-1475.10.1007/s11666-022-01360-w ↗
4. L. Pawlowski, Suspension and Solution Thermal Spray Coatings, Surf. Coat. Tech., 2009, 203(19), p 2807-2829.10.1016/j.surfcoat.2009.03.005 ↗
5. F. Trenkle, M. Winkelmann, F. Wüst, J. Luth, S. Hartmann, P. Krieg, and A. Killinger, Dünne Metallische Heizschichten, Hergestellt Durch Suspensionsspritzen, Therm. Spray Bull., 2019, 12, p 72-76.
6. M. Michalak, L. Latka, P. Sokolowski, F.-L. Toma, H. Myalska, A. Denoirjean, and H. Ageorges, Microstructural, Mechanical and Tribological Properties of Finely Grained Al2O3 Coatings Obtained by SPS and S-HVOF Methods, Surf. Coat. Technol., 2020, 404, 126463.10.1016/j.surfcoat.2020.126463 ↗
7. R. Vaßen, E. Bakan, D.E. Mack, and O. Guillon, A Perspective on Thermally Sprayed Thermal Barrier Coatings: Current Status and Trends, J. Therm. Spray Technol., 2022, 31(4), p 685-698.10.1007/s11666-022-01330-2 ↗
8. H. Kummer, M. Winkelmann, F. Wüst, S. Hartmann, F. Trenkle, P. Krieg, and A. Killinger, “Thermal Spray 2022: Proceedings from the International Thermal Spray Conference, Suspension Sprayed Thin Metallic Coatings for Electric Panel Heaters,” (Vienna, Austria), 2022, p 581-585, https://doi.org/10.31399/asm.cp.itsc2022p0581.10.31399/asm.cp.itsc2022p0581 ↗
9. N. Kumar, M. Gupta, D.E. Mack, G. Mauer, and R. Vaßen, Columnar Thermal Barrier Coatings Produced by Different Thermal Spray Processes, J. Therm. Spray Technol., 2021, 30(6), p 1437-1452.10.1007/s11666-021-01228-5 ↗
10. S. Goel, S. Björklund, N. Curry, U. Wiklund, and S. Joshi, Axial Suspension Plasma Spraying of Al2O3 Coatings for Superior Tribological Properties, Surf. Coat. Tech., 2017, 315, p 80-87.10.1016/j.surfcoat.2017.02.025 ↗
11. G. Bolelli, J. Rauch, V. Cannillo, A. Killinger, L. Lusvarghi, and R. Gadow, Microstructural and Tribological Investigation of High-Velocity Suspension Flame sprayed (HVSFS) Al2O3 Coatings, J. Therm. Spray Technol., 2009, 18(1), p 35-49.10.1007/s11666-008-9279-9 ↗
12. P. Junge, E.M. Heppke, R. Kleba-Ehrhardt, D. Karl, G. Cios, and C. Rupprecht, Phase Evolution and Microstructure of Suspension HVOF-Sprayed Alumina Coatings, Surf. Coat. Technol., 2025, 499, 131885.10.1016/j.surfcoat.2025.131885 ↗
13. M. Blum, E. Gyoktepeliler-Akin, and A. Killinger, High Velocity Suspension Flame Spraying of AlN/Al2O3 Composite Coatings, Surf. Coat. Technol., 2022, 441, 128588.10.1016/j.surfcoat.2022.128588 ↗
14. M.C. Lanzino, A. Höppel, L.R.V. Le, S. Morelli, A. Killinger, W. Rheinheimer, H.O. Mayr, S. Dembski, A. Al-Ahmad, M.F. Mayr, U. Gbureck, and M. Seidenstuecker, Biodegradable, Antibacterial TCP Implant Coatings with Magnesium Phosphate-Based Supraparticles, J. Biomed. Mater. Res. A, 2025, 113(7), e37963.10.1002/jbm.a.37963 ↗
15. M.C. Lanzino, L.-Q.R.V. Le, A. Höppel, A. Killinger, W. Rheinheimer, S. Dembski, A. Al-Ahmad, H.O. Mayr, and M. Seidenstuecker, Suspension-Sprayed Calcium Phosphate Coatings with Antibacterial Properties, JFB, 2024, 15(10), 281.10.3390/jfb15100281 ↗
16. H. Memon, K. Leng, A. Rincón Romero, S. Lokachari, N. Curry, and T. Hussain, Suspension High-Velocity Oxy-Fuel–Sprayed Dense Vertically Cracked and Suspension-Plasma-Sprayed Columnar Yttria-Stabilized Zirconia Coatings: Calcia Magnesia Alumino Silicates Infiltration and Thermal Cycling Performance, Adv. Eng. Mater., 2024, 26(3), 2300879.10.1002/adem.202300879 ↗
17. A. Meyer, F.-L. Toma, O. Kunze, A. Böhme, B. Matthey, A. Potthoff, A. Kaiser, T. Gestrich, and C. Leyens, Development of Suspension Feedstocks for Thermally Sprayed Zn2TiO4 Coatings, J. Therm. Spray Tech., 2023, 32(2-3), p 502-513.10.1007/s11666-023-01552-y ↗
18. M. Sauter, C. Semmler, T. Nies, G. Poppi, L. Bortolotti, F. Ottani, G. Bolelli, L. Lusvarghi, and A. Killinger, High Temperature Properties of Nichrome Resistant Heaters: A Systematic Comparison of APS, Suspension and Filament HVOF Sprayed Coatings, Surf. Coat. Technol., 2025, 496, 131594.10.1016/j.surfcoat.2024.131594 ↗
19. M. Sauter, A. Roth, A. Grebhardt, and A. Killinger, High Velocity Flame Spraying of Highly-Filled Ceramic: Polymer Filaments (F-HVOF), Surf. Coat. Tech., 2023, 458, 129324.10.1016/j.surfcoat.2023.129324 ↗
20. M. Hauer, M. Meyer, D. Billieres, C. Bricquet, F. Gerstgrasser, J. Kiilakoski, J. Lejay, and K.-M. Henkel, Use of Different Process Gases for Manufacturing Isolating Alumina Coatings by Flame Spraying with Cords, J. Therm. Spray Technol., 2021, 30(1-2), p 222-235.10.1007/s11666-021-01160-8 ↗
21. A.R. Lopez, B. Hassan, W.L. Oberkampf, R.A. Neiser, and T.J. Roemer, Computational Fluid Dynamics Analysis of a Wire-Feed, High-Velocity Oxygen Fuel (HVOF) Thermal Spray Torch, J. Therm. Spray Technol., 1998, 7, p 374-382.10.1361/105996398770350855 ↗
22. C.N. Eastwick, K.A. Simmons, and D.G. McCartney, Computational Fluid Dynamic Modeling of Gas Flow Characteristics in a High-Velocity Oxy-Fuel Thermal Spray System, J. Therm. Spray Technol., 2001, 10(3), p 461-469.10.1361/105996301770349231 ↗
23. S. Kamnis, and S. Gu, Numerical Modelling of Propane Combustion in a High Velocity Oxygen-Fuel Thermal Spray Gun, Chem. Eng. Process. Process Intensif., 2006, 45(4), p 246-253.10.1016/j.cep.2005.06.011 ↗
24. E. Dongmo, R. Gadow, A. Killinger, and M. Wenzelburger, Modeling of Combustion as well as Heat, Mass, and Momentum Transfer During Thermal Spraying by HVOF and HVSFS, J. Therm. Spray Technol., 2009, 18(5-6), p 896-908.10.1007/s11666-009-9341-2 ↗
25. F.-L. Toma, L.-M. Berger, C.C. Stahr, T. Naumann, and S. Langner, Microstructures and Functional Properties of Suspension-Sprayed Al2O3 and TiO2 Coatings: An Overview, J. Therm. Spray Technol., 2010, 19(1-2), p 262-274.10.1007/s11666-009-9417-z ↗
26. A. Karabeyoglu, G. Zilliac, B.J. Cantwell, S. DeZilwa, and P. Castellucci, Scale-Up Tests of High Regression Rate Paraffin-Based Hybrid Rocket Fuels, J. Propuls. Power, 2004, 20(6), p 1037-1045.10.2514/1.3340 ↗
27. L. Krishnamurthy, and F.A. Williams, On the Temperatures of Regressing PMMA Surfaces, Combust. Flame, 1973, 20(2), p 163-169.10.1016/S0010-2180(73)80170-1 ↗
28. Y. Wang, S. Hu, X. Liu, Y. Zhang, and L. Liu, Droplet Entrainment and its Role in the Combustion of HTPB/Paraffin Fuels, Acta Astronaut., 2023, 204, p 107-115.10.1016/j.actaastro.2022.12.042 ↗
29. M. Karabeyoglu, B. Cantwell, and D. Altman, “Development and Testing of Paraffin-Based Hybrid Rocket Fuels,” 37th Joint Propulsion Conference and Exhibit, (Salt Lake City, UT, U.S.A.), American Institute of Aeronautics and Astronautics, 2001, https://doi.org/10.2514/6.2001-4503.10.2514/6.2001-4503 ↗
30. M.A. Karabeyoglu, D. Altman, and B.J. Cantwell, Combustion of Liquefying Hybrid Propellants: Part 1, General Theory, J. Propul. Power, 2002, 18(3), p 610-620.10.2514/2.5975 ↗
31. C.L. Beyler, and M.M. Hirschler, Thermal Decomposition of Polymers, SFPE Handbook of Fire Protection Engineering, National Fire Protection Association Quincy, MA, 2002, 2(7), p 111-131.
32. N. Khalturinskii and Springer, High-Temperature Pyrolysis of Polymers, J. Therm. Anal., 1987, 32, p 1675-1682.10.1007/BF01913945 ↗
33. A.R. De Matos Costa, A. Crocitti, L. Hecker De Carvalho, S.C. Carroccio, P. Cerruti, and G. Santagata, Properties of Biodegradable Films Based on Poly(Butylene Succinate) (PBS) and Poly(Butylene Adipate-Co-Terephthalate) (PBAT) Blends, Polymers, 2020, 12(10), 2317.10.3390/polym12102317 ↗
34. D. Bianchi, G. Leccese, F. Nasuti, M. Onofri, and C. Carmicino, Modeling of High Density Polyethylene regression Rate in the Simulation of Hybrid Rocket Flowfields, Aerospace, 2019, 6(8), 88.10.3390/aerospace6080088 ↗
35. R. Zevenhoven, M. Karlsson, M. Hupa, and M. Frankenhaeuser, Combustion and Gasification Properties of Plastics Particles, J. Air Waste Manage. Assoc., 1997, 47(8), p 861-870.10.1080/10473289.1997.10464461 ↗
36. K.K. Kuo, and M.J. Chiaverini, Eds., “Fundamentals of Hybrid Rocket Combustion and Propulsion,” American Institute of Aeronautics and Astronautics. (2007). https://doi.org/10.2514/4.866876.10.2514/4.866876 ↗
37. J.A. Razak, H.M. Akil, and H. Ong, Effect of Inorganic Fillers on the Flammability Behavior of Polypropylene Composites, J. Thermoplast. Compos. Mater., 2007, 20(2), p 195-205.10.1177/0892705707073181 ↗
38. B. Yuan, G. Chen, Y. Zou, S. Shang, Y. Sun, B. Yu, S. He, and X. Chen, Alumina Nanoflake-Coated Graphene Nanohybrid as a Novel Flame Retardant Filler for Polypropylene, Polym. Adv. Technol., 2019, 30(8), p 2153-2158.10.1002/pat.4689 ↗
39. V. Sharma, S. Agarwal, A. Mathur, S. Singhal, and S. Wadhwa, Advancements in Nanomaterial Based Flame-Retardants for Polymers: A Comprehensive Overview, J. Ind. Eng. Chem., 2024, 133, p 38-52.10.1016/j.jiec.2023.12.010 ↗
40. M. Li, and P.D. Christofides, Computational Study of Particle in-Flight Behavior in the HVOF Thermal Spray Process, Chem. Eng. Sci., 2006, 61(19), p 6540-6552.10.1016/j.ces.2006.05.050 ↗
41. A. Killinger, Status and Future Trends in Suspension Spray Techniques, Future Dev. Therm. Spray Coat., 2015 https://doi.org/10.1016/B978-0-85709-769-9.00004-X10.1016/B978-0-85709-769-9.00004-X ↗
42. F.-X. Collard, and J. Blin, A Review on Pyrolysis of Biomass Constituents: Mechanisms and Composition of the Products Obtained from the Conversion of Cellulose, Hemicelluloses and Lignin, Renew. Sustain. Energy Rev., 2014, 38, p 594-608.10.1016/j.rser.2014.06.013 ↗
43. H. Chen, F. Chen, H. Chen, H. Liu, L. Chen, and L. Yu, Thermal Degradation and Combustion Properties of Most Popular Synthetic Biodegradable Polymers, Waste Manag. Res., 2023, 41(2), p 431-441.10.1177/0734242X221129054 ↗
44. C.K. Law, A. Makino, and T.F. Lu, On the Off-Stoichiometric Peaking of Adiabatic Flame Temperature, Combust. Flame, 2006, 145(4), p 808-819.10.1016/j.combustflame.2006.01.009 ↗
45. T. Kashiwagi, Polymer Combustion and Flammability: Role of the Condensed Phase, Symposium (International) on Combustion, 1994, 25(1), p 1423-1437.10.1016/S0082-0784(06)80786-1 ↗
46. R. Sonnier, B. Otazaghine, L. Ferry, and J.-M. Lopez-Cuesta, Study of the Combustion Efficiency of Polymers Using a Pyrolysis-Combustion Flow Calorimeter, Combust. Flame, 2013, 160(10), p 2182-2193.10.1016/j.combustflame.2013.04.009 ↗
47. A. Zimmer, The Effect of Cooling Rate in Thermally Sprayed Alumina, J. Ceram. Process. Res., 2010, 11, p 221-224.
48. L.L. Shaw, D. Goberman, R. Ren, M. Gell, S. Jiang, Y. Wang, T.D. Xiao, and P.R. Strutt, The Dependency of Microstructure and Properties of Nanostructured Coatings on Plasma Spray Conditions, Surf. Coat. Technol., 2000, 130(1), p 1-8.10.1016/S0257-8972(00)00673-3 ↗
49. O. Ali, R. Ahmed, F.-L. Toma, L.-M. Berger, B. Matthey, N. Faisal, and K. Ahmed, Influence of Feedstock and Thermal Spray Process on the Phase Composition of Alumina Coatings and Their Sliding Wear, J. Therm. Spray Technol., 2023, 32(7), p 2028-2053.10.1007/s11666-023-01597-z ↗
50. M. Michalak, P. Sokołowski, M. Szala, M. Walczak, L. Łatka, F.-L. Toma, and S. Björklund, Wear Behavior Analysis of Al2O3 Coatings Manufactured by APS and HVOF Spraying Processes Using Powder and Suspension Feedstocks, Coatings, 2021, 11(8), 879.10.3390/coatings11080879 ↗
51. J.W. Murray, A.S.M. Ang, Z. Pala, E.C. Shaw, and T. Hussain, Suspension High Velocity Oxy-Fuel (SHVOF)-Sprayed Alumina Coatings: Microstructure Nanoindentation and Wear, J. Therm. Spray Tech, 2016, 25(8), p 1700-1710.10.1007/s11666-016-0462-0 ↗
52. G. Bolelli, V. Cannillo, R. Gadow, A. Killinger, L. Lusvarghi, T. Manfredini, and P. Müller, Properties of Al2O3 Coatings by High Velocity Suspension Flame Spraying (HVSFS): Effects of Injection Systems and Torch Design, Surf. Coat. Technol., 2015, 270, p 175-189.10.1016/j.surfcoat.2015.03.005 ↗
53. T.A. Owoseni, M. Bai, N. Curry, E.H. Lester, D.M. Grant, and T. Hussain, Residual Stress Measurement of Suspension HVOF-Sprayed Alumina Coating via a Hole-Drilling Method, J. Therm. Spray Technol., 2020, 29(6), p 1339-1350.10.1007/s11666-020-01072-z ↗