journal article·2026-03

Influence of Pulsed Laser Ablation Parameters on Adhesion of Cold Spray Al 6061 Coatings on Extruded Al 6061 Substrates

Jagannadh Sripada, Alexis Thibault, Lucas Hof, Philippe Bocher, Jean-François Béland, Phuong Vo, Éric Irissou

Journal of Thermal Spray Technology· Volume 35· Issue 2-3
Publisher page

Abstract

The effect of pulsed laser ablation as a substrate pretreatment technique on the adhesive strength of cold-sprayed Al6061 coatings deposited onto extruded Al6061 substrates was investigated. The influence of laser ablation parameters on the surface morphology and roughness of extruded Al 6061 substrates were systematically examined. A Nd:YAG pulsed laser (1.064 µm, 12 ns, 30 Hz) was employed with fluences ranging from 1.55 to 3.53 J/cm² and surface coverages between 5.8 × and 109.6 × . Distinct morphological evolution stages were observed, progressing from irradiated and dimpled textures at low laser exposures to cauliflower-like structures at higher exposures. This transformation was primarily governed by cumulative surface coverage resulting from overlapping laser passes, indicating that surface coverage plays a more dominant role than fluence in driving morphological changes. Surface texturing emerged at a threshold of approximately 8.4 × coverage. Cold spray deposition was subsequently performed on the laser-textured substrates and compared to coatings prepared using conventional pretreatments, including grit blasting and degreasing. Adhesion strength was assessed via two mechanical testing methods (ASTM C633 and a modified ASTM E8). Laser texturing produced substantial improvements in coating adhesion, with increases of up to 242% relative to grit-blasted substrates. A maximum bond strength of 90 MPa was achieved at a fluence of 3.53 J/cm² and 8.4 × surface coverage. These findings demonstrate that controlled laser ablation can effectively tailor surface morphology to significantly enhance the adhesion performance of cold-sprayed Al 6061 coatings.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Erosion and Abrasive Machining · Cellular and Composite Structures

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (51)

Show source-provided references
1. CM Kay J Karthikeyan 2016 Introduction to cold spray High Pressure Cold Spray: Principles and Applications ASM International Materials Park, Ohio, USA 1 1110.31399/asm.tb.hpcspa.9781627082853 ↗
2. S. Yin, P. Cavaliere, B. Aldwell, R. Jenkins, H. Liao, W. Li and R. Lupoi, Cold Spray Additive Manufacturing and Repair: Fundamentals and Applications, Addit. Manuf., 2018, 21, p 628–650.
3. R.C. Dykhuizen and M.F. Smith, Gas Dynamic Principles of Cold Spray, J. Therm. Spray Technol., 1998, 7(2), p 205–212.10.1361/105996398770350945 ↗
4. H. Assadi, H. Kreye, F. Gärtner and T. Klassen, Cold Spraying – a Materials Perspective, Acta Mater., 2016, 116, p 382–407.10.1016/j.actamat.2016.06.034 ↗
5. A. Vardelle, C. Moreau, J. Akedo, H. Ashrafizadeh, C.C. Berndt, J.O. Berghaus, M. Boulos, J. Brogan, A.C. Bourtsalas, A. Dolatabadi, M. Dorfman, T.J. Eden, P. Fauchais, G. Fisher, F. Gaertner, M. Gindrat, R. Henne, M. Hyland, E. Irissou, E.H. Jordan, K.A. Khor, A. Killinger, Y.-C. Lau, C.-J. Li, L. Li, J. Longtin, N. Markocsan, P.J. Masset, J. Matejicek, G. Mauer et al., The 2016 Thermal Spray Roadmap, J. Therm. Spray. Tech., 2016, 25(8), p 1376–1440.10.1007/s11666-016-0473-x ↗
6. JR Davis 2001 Aluminum and Aluminum Alloys, Alloying: Understanding the Basics 11th ed. Materials Park, Ohio, USA 351 41610.31399/asm.tb.aub.t61170351 ↗
7. A. Selvaggio, M. Haase, N.B. Khalifa and A.E. Tekkaya, Extrusion of profiles with variable wall thickness, Procedia CIRP, 2014, 18, p 15–20.10.1016/j.procir.2014.06.100 ↗
8. M.R. Rokni, C.A. Widener and V.R. Champagne, Microstructural Evolution of 6061 Aluminum Gas-Atomized Powder and High-Pressure Cold-Sprayed Deposition, J. Therm. Spray. Tech., 2014, 23(3), p 514–524.10.1007/s11666-013-0049-y ↗
9. M.R. Rokni, C.A. Widener and V.R. Champagne, Microstructural Stability of Ultrafine Grained Cold Sprayed 6061 Aluminum Alloy, Appl. Surf. Sci., 2014, 290, p 482–489.10.1016/j.apsusc.2013.11.127 ↗
10. M.R. Rokni, C.A. Widener, O.C. Ozdemir and G.A. Crawford, Microstructure and Mechanical Properties of Cold Sprayed 6061 Al in as-sprayed and Heat Treated Condition, Surf. Coat. Technol., 2017, 309, p 641–650.10.1016/j.surfcoat.2016.12.035 ↗
11. A. Sabard, H.L. de Villiers Lovelock and T. Hussain, Microstructural Evolution in Solution heat Treatment of Gas-Atomized Al Alloy (7075) Powder for Cold Spray, J. Therm. Spray Tech., 2018, 27(1), p 145–158.10.1007/s11666-017-0662-2 ↗
12. A. Sabard and T. Hussain, Inter-particle bonding in cold spray deposition of a gas-atomised and a solution heat-treated Al 6061 powder, J. Mater. Sci., 2019, 54(18), p 12061–12078.10.1007/s10853-019-03736-w ↗
13. B.A. Bedard, T.J. Flanagan, A.T. Ernst, A. Nardi, A.M. Dongare, H.D. Brody, V.K. Champagne, S.-W. Lee and M. Aindow, Microstructure and micromechanical response in gas-atomized Al 6061 alloy powder and cold-sprayed splats, J. Therm. Spray. Tech., 2018, 27(8), p 1563–1578.10.1007/s11666-018-0785-0 ↗
14. A.G. Gavras, D.A. Lados, V.K. Champagne and R.J. Warren, Effects of processing on microstructure evolution and fatigue crack growth mechanisms in cold-spray 6061 aluminum alloy, Int. J. Fatigue, 2018, 110, p 49–62.10.1016/j.ijfatigue.2018.01.006 ↗
15. A.G. Gavras, D.A. Lados, V.K. Champagne, R.J. Warren and D. Singh, Small Fatigue Crack Growth Mechanisms and Interfacial Stability in Cold-Spray 6061 Aluminum Alloys and Coatings, Metall. Mater. Trans. A, 2018, 49(12), p 6509–6520.10.1007/s11661-018-4929-0 ↗
16. P. Nautiyal, C. Zhang, V.K. Champagne, B. Boesl and A. Agarwal, In-situ MechanIcal Investigation of the Deformation of Splat Interfaces in Cold-Sprayed Aluminum Alloy, Mater. Sci. Eng. A, 2018, 737, p 297–309.10.1016/j.msea.2018.09.065 ↗
17. P. Nautiyal, C. Zhang, V. Champagne, B. Boesl and A. Agarwal, In-situ Creep Deformation of Cold-Sprayed Aluminum Splats at Elevated Temperatures, Surf. Coat. Technol., 2019, 372, p 353–360.10.1016/j.surfcoat.2019.05.045 ↗
18. T. Paul, P. Nautiyal, C. Zhang, B. Boesl and A. Agarwal, Role of in-situ Splat Sintering on Elastic and Damping Behavior of Cold Sprayed Aluminum Coatings, Scripta Mater., 2021, 204, 114125.10.1016/j.scriptamat.2021.114125 ↗
19. T.B. Mangalarapu, S. Kumar, M. Ramakrishna, P. Gandham and K. Suresh, Precipitation Behavior of Cold Sprayed Al6061 Coatings, Materialia, 2022, 24, 101510.10.1016/j.mtla.2022.101510 ↗
20. A. Nourian, T. Schwartz, S. Boese and S. Müftü, Effects of Process Parameters on Cold Spray Deposition of Al-6061 Alloy, J. Therm. Spray Tech., 2022, 31(8), p 2517–2536.10.1007/s11666-022-01456-3 ↗
21. A. Nourian and S. Müftü, Effect of Substrate Surface Finish and Particle Velocity on Fatigue Performance of Cold spray Coated A6061 Aluminum Alloy, Surf. Coat. Technol., 2022, 444, 128676.10.1016/j.surfcoat.2022.128676 ↗
22. A. Nourian, C. Beamer and S. Muftu, Effects of Post-Deposition Processing on Static and Cyclic Performance of Cold Sprayed 6061 Aluminum Alloy, Addit. Manuf., 2024, 88, 104246.
23. C.M. Sample, A.G. Spangenberger, V.K. Champagne and D.A. Lados, Mechanical Properties and Growth Mechanisms of Long and Small Fatigue Cracks in as-Deposited Bulk Cold Spray Al-6061, Int. J. Fatigue, 2024, 181, 108152.10.1016/j.ijfatigue.2024.108152 ↗
24. E. Lin, Q. Chen, O.C. Ozdemir, V.K. Champagne and S. Müftü, Effects of Interface Bonding on the Residual Stresses in Cold-Sprayed Al-6061: a Numerical Investigation, J. Therm. Spray Technol., 2019, 28(3), p 472–483.10.1007/s11666-019-00827-7 ↗
25. Q. Wang, N. Ma, X.-T. Luo and C.-J. Li, Towards better Understanding supersonic impact-bonding behavior of cold sprayed 6061–T6 aluminum alloy based on a high-accuracy material model, Addit. Manuf., 2021, 48, 102469.
26. D.K. Christoulis, M. Jeandin, E. Irissou, J.-G. Legoux, W. Knapp, D.K. Christoulis, M. Jeandin, E. Irissou, J.-G. Legoux and W. Knapp, Laser-Assisted Cold Spray (LACS), Nd YAG Laser, IntechOpen, 2012 https://doi.org/10.5772/3610410.5772/36104 ↗
27. E. Irissou, J.-G. Legoux, B. Arsenault and C. Moreau, Investigation of Al-Al2O3 Cold Spray Coating Formation and Properties, J. Therm. Spray Technol., 2007, 16(5–6), p 661–668.10.1007/s11666-007-9086-8 ↗
28. C. Coddet, G. Montavon, S. Ayrault-Costil, O. Freneaux, F. Rigolet, G. Barbezat, F. Folio, A. Diard and P. Wazen, Surface Preparation and Thermal Spray in a Single Step: the PROTAL Process—Example of Application for an Aluminum-Base Substrate, J. Therm. Spray Technol., 1999, 8(2), p 235–242.10.1361/105996399770350467 ↗
29. D.K. Christoulis, S. Guetta, E. Irissou, V. Guipont, M.H. Berger, M. Jeandin, J.-G. Legoux, C. Moreau, S. Costil, M. Boustie, Y. Ichikawa and K. Ogawa, Cold-Spraying Coupled to Nano-Pulsed Nd-YaG Laser Surface Pre-Treatment, Journal of Thermal Spray Technology, Springer Science and Business Media LLC, 2010, 19(5), p 1062–1073.10.1007/s11666-010-9500-5 ↗
30. Y. Danlos, S. Costil, X. Guo, H. Liao and C. Coddet, Ablation Laser and Heating Laser Combined to Cold Spraying, Surf. Coat. Technol., 2010, 205(4), p 1055–1059.10.1016/j.surfcoat.2010.06.018 ↗
31. C. Zhang, D. Zhang, C. Luo, W. Peng, X. Zang, and MDPI AG, Nanosecond-Pulse Laser Assisted Cold Spraying of Al–Cu Aluminum Alloy, Coatings, 2021, 11(3), 267.10.3390/coatings11030267 ↗
32. M. Perton, S. Costil, W. Wong, D. Poirier, E. Irissou, J.-G. Legoux, A. Blouin and S. Yue, Effect of Pulsed Laser Ablation and Continuous Laser Heating on the Adhesion and Cohesion of Cold Sprayed Ti-6Al-4V Coatings, Journal of Thermal Spray Technology, Springer Science and Business Media LLC, 2012, 21(6), p 1322–1333.10.1007/s11666-012-9812-8 ↗
33. J. Yuan, L. Liang, G. Lin, and IOP Publishing, Study of laser surface texturing of 6061 aluminium with thermal assistance, J. Micromech. Microeng., 2020, 30(3), p 035003.10.1088/1361-6439/ab5edb ↗
34. D. Poirier, J.-G. Legoux, P. Vo, B. Blais, J.D. Giallonardo and P.G. Keech, Powder Development and Qualification for High-Performance Cold Spray Copper Coatings on Steel Substrates, J Thermal Spray Technol, 2019, 28, p 444–459.10.1007/s11666-019-00833-9 ↗
35. “Standard Test Method for Adhesion or Cohesion Strength of Thermal Spray Coatings,” C 633, Annual Book of ASTM Sta ndards, ASTM International, 2021
36. “Standard Test Methods for Tension Testing of Metallic Materials,” E 8, Annual Book of ASTM Standards, ASTM International, 2016.
37. R.N. Raoelison, Y. Xie, T. Sapanathan, M.P. Planche, R. Kromer, S. Costil and C. Langlade, Cold gas dynamic spray technology: a comprehensive review of processing conditions for various technological developments till to date, Addit. Manuf., 2018, 19, p 134–159.
38. T. Schmidt, H. Assadi, F. Gärtner, H. Richter, T. Stoltenhoff, H. Kreye and T. Klassen, From Particle Acceleration to Impact and Bonding in Cold spraying, J. Therm. Spray Tech., 2009, 18(5), p 794–808.10.1007/s11666-009-9357-7 ↗
39. T. Samson, D. MacDonald, R. Fernández, and B. Jodoin, Effect of Pulsed Waterjet Surface Preparation on the Adhesion Strength of Cold Gas Dynamic Sprayed Aluminum Coatings Springer 2015 J. Therm. Spray Technol. 24 984 993 https://doi.org/10.1007/s11666-015-0261-z10.1007/s1166 ↗
40. S. Pratheesh Kumar, S. Elangovan, R. Mohanraj and V. Sathya Narayanan, Significance of Continuous Wave and Pulsed Wave Laser in Direct Metal Deposition, Mater. Today Proc., 2021, 46, p 8086–8096.10.1016/j.matpr.2021.03.041 ↗
41. K.C. Phillips, H.H. Gandhi, E. Mazur, S.K. Sundaram, and Optica Publishing Group, Ultrafast Laser Processing of Materials: a Review, Adv. Opt. Photon., 2015, 7, p 684–712. https://doi.org/10.1364/AOP.7.00068410.1364/AOP.7.000684 ↗
42. P. Lorazo, L.J. Lewis, M. Meunier, and American Physical Society, Thermodynamic Pathways to Melting, Ablation, and Solidification in Absorbing Solids Under Pulsed Laser Irradiation, Phys. Rev. B, 2006, 73(13), 134108.10.1103/PhysRevB.73.134108 ↗
43. S.K. Sundaram and E. Mazur, Inducing and Probing Non-Thermal Transitions in Semiconductors Using Femtosecond Laser Pulses, Nature Mater, Nature Publishing Group, 2002, 1(4), p 217–224.10.1038/nmat767 ↗
44. D. Baüerle, Laser Processing and Chemistry, 4th ed. Springer, Berlin, Germany, 2011.10.1007/978-3-642-17613-5 ↗
45. B.N. Chichkov, C. Momma, S. Nolte, F. von Alvensleben and A. Tünnermann, Femtosecond, Picosecond and Nanosecond Laser Ablation of Solids, Appl. Phys. A, 1996, 63(2), p 109–115.10.1007/BF01567637 ↗
46. S. Choi, C.S. Kim, K.-Y. Jhang and W.-S. Shin, Surface Characteristics of Aluminum 6061–T6 Subjected to Nd:YAG Pulsed-Laser Irradiation, J. Mech. Sci. Technol., 2012, 26(7), p 2163–2166.10.1007/s12206-012-0537-x ↗
47. M. Soileau, Ripple Structures Associated with Ordered Surface Defects in Dielectrics, IEEE J. Quantum Electron., 1984, 20(5), p 464–467.10.1109/JQE.1984.1072422 ↗
48. R. Buividas, M. Mikutis and S. Juodkazis, Surface and Bulk Structuring of Materials by Ripples with Long and Short Laser Pulses: Recent Advances, Prog. Quantum Electron., 2014, 38(3), p 119–156.10.1016/j.pquantelec.2014.03.002 ↗
49. J. Bonse, S.V. Kirner and J. Krüger, Laser-Induced Periodic Surface Structures (LIPSS), Handbook of Laser Micro- and Nano-Engineering. Springer, Cham, 2021, p 1–59.
50. M. Rezayat, A. Valencia-Cadena, J.J. Roa and A. Mateo, Assessing the Influence of Laser Surface Texturing on the Fatigue Behavior of AISI 301LN Stainless Steel, Mater. Sci. Eng. A, 2025, 923, 147756.10.1016/j.msea.2024.147756 ↗
51. Y.M. Champagne and J.W. Palko, Particle-Based Simulation of Cold Spray: Influence of Oxide Layer on Impact Process, Addit. Manuf., 2021, 37, 101517.