journal article·2026-04Open access

Comparative Analysis of HVAF and Cold Spray Methods for Aluminum Alloy Coatings for Engine Bearings

I. Ozdemir, T. Grund, S. Joshi, S. Björklund, B. Bulbul, R. Drehmann, T. Lampke

Abstract

Abstract The use of advanced aluminum-based bimetal bearings is critical for addressing modern automotive demands such as downsizing, higher loads, and improved fuel efficiency. Traditional roll bonding methods, widely employed for manufacturing bimetal bearings, face significant limitations when applied to next-generation aluminum alloys due to their complexity, cost, and inflexibility. This study evaluates thermal spray techniques, specifically cold spray (CS) and high-velocity air fuel (HVAF) deposition, as alternative manufacturing methods for aluminum-based bimetal bearings. Cold spray trials showed that the AlMn1Cu bond coat achieved > 88% deposition efficiency (DE) at 500-600 °C, while the AlZn5SiCuMgBi top coat reached only 32.69% at 650 °C. The lower DE of the top coat is attributed to its higher hardness and the presence of preexisting intermetallic phases (e.g., Bi 2 Mg 3 ), which are only partially reduced during deposition and may undermine particle bonding. Experimental comparisons between HVAF and cold spray (CS) coatings revealed significant differences in mechanical and tribological performance. HVAF coatings exhibited superior hardness of 151 HV compared to cold spray, which had 94.5 HV, indicating a more robust and potentially wear-resistant surface. In terms of wear behavior, HVAF demonstrated lower wear depth of 83.3 µm and volume loss of 0.137 mm 3 , which are 21.5% and 22.5% lower, respectively, compared to cold spray, which had wear depths of 106.1 µm and volume loss of 0.1767 mm 3 . These results reflect the denser microstructure and improved bonding achieved by HVAF. Additionally, friction coefficient (COF) measurements showed that HVAF with a COF of 0.5 outperformed cold spray with a COF of 0.625, further emphasizing its superior tribological properties.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: High-Temperature Coating Behaviors · High Entropy Alloys Studies · Intermetallics and Advanced Alloy Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (18)

Show source-provided references
1. D.W. Gebretsadik, J. Hardell and B. Prakash, Seizure Behaviour of Some Selected Pb-Free Engine Bearing Materials Under Lubricated condition, Tribol. Int., 2017, 111, p 265-275.10.1016/j.triboint.2017.03.021 ↗
2. I. Ozdemir, B. Bulbul, U. Kiracbedel, T. Grund and T. Lampke, Wear Performance Evaluation of Polymer Overlays on Engine Bearings, Materials (Basel, Switzerland), 2024 https://doi.org/10.3390/ma1715380210.3390/ma17153802 ↗
3. T. Marrocco, L.C. Driver, S.J. Harris and D.G. McCartney, Microstructure and Properties of Thermally Sprayed Al-Sn-Based Alloys for Plain Bearing Applications, J. Therm. Spray Technol., 2006, 15(4), p 634-639.10.1361/105996306X147009 ↗
4. R.V. Reyes, L.C. Casteletti, A. Garcia and J.E. Spinelli, Characterization of Microstructure and Wear Resistance of a Monotectic Al-Bi-Zn Alloy, J. Phys. Chem. Solids, 2020, 147, p 109631.10.1016/j.jpcs.2020.109631 ↗
5. N.A. Abdelhakim and R.M. Shalaby, Microstructures and Mechanical Properties of Al-Zn-Sn Bearing Alloys for High Performance Applications, WJET, 2021, 09(03), p 637-652.10.4236/wjet.2021.93045 ↗
6. H.A. Khan, K. Asim, F. Akram, A. Hameed, A. Khan and B. Mansoor, Roll Bonding Processes: State-of-the-Art and Future Perspectives, Metals, 2021, 11(9), p 1344.10.3390/met11091344 ↗
7. D.-H. Jeong, Y.-S. Lee, H.-W. Kim, Y.-D. Kim, Q. Zang and D. Feng, Microstructure and Mechanical Properties of High-Strength Al-Zn-Mg-Ni Alloys with Excellent Twin-Roll Castability, J. Mater. Res. Technol., 2024, 33(1), p 5064-5074.10.1016/j.jmrt.2024.10.154 ↗
8. G. Barbezat, Coating Deposition of Bearing Materials on Connecting Rod By Thermal Spraying, E. Lugscheider, Ed., 02.05.2005 - 04.05.2005 (Basel, Switzerland), Verlag für Schweißen und verwandte Verfahren DVS-Verlag GmbH, 2005, p 642-64510.31399/asm.cp.itsc2005p0642 ↗
9. R.S. Sonia, N.M. Walia, S. Suri and A. Chaudhary, Tyagi, 2021 Potential Applications of Thermal Spray Coating For I.C. Engine Tribology: A Review, J. Phys. Conf. Ser., 1950, 1, p 12041.
10. A. Meghwal, E. Bosi, A. Anupam, C. Hall, S. Björklund, S. Joshi, P. Munroe, C.C. Berndt and A.S.M. Ang, Microstructure, Multi-scale Mechanical and Tribological Performance of Hvaf Sprayed Alcocrfeni High-Entropy Alloy Coating, J. Alloys Compd., 2024, 1005(5), p 175962.10.1016/j.jallcom.2024.175962 ↗
11. T.B. Mangalarapu, S. Kumar, P. Gandham and S. Koppoju, Cold spraying of Al-Aerospace alloys: Ease of coating deposition at high stagnation temperatures, Surf. Coat. Technol., 2023, 467, p 129703.10.1016/j.surfcoat.2023.129703 ↗
12. W. Sun, X. Chu, H. Lan, R. Huang, J. Huang, Y. Xie, J. Huang and G. Huang, Current Implementation Status of Cold Spray Technology: A Short Review, J. Therm. Spray Technol., 2022, 31(4), p 848-865.10.1007/s11666-022-01382-4 ↗
13. R.H.A. Shiddieqy, A. Wikarta, A.S. Pramono, Y. Suwarno and J.-T. Tsai, Addressing Challenges in Deposition Efficiency and Material Compatibility in Low-Pressure Cold Spray Systems, Results in Engineering, 2025, 26(12), p 105065.10.1016/j.rineng.2025.105065 ↗
14. G. Mauer, K.-H. Rauwald, Y.J. Sohn and R. Vaßen, The Potential of High-Velocity Air-Fuel Spraying (Hvaf) to Manufacture Bond Coats for Thermal Barrier Coating Systems, J. Therm. Spray Technol., 2024, 33(2–3), p 746-755.10.1007/s11666-023-01659-2 ↗
15. C. Zhang, T. Molla, C. Brandl, J. Watts, R. McCully, C. Tang and G. Schaffer, Critical Velocity and Deposition Efficiency in Cold Spray: A Reduced-Order Model and Experimental Validation, J. Manuf. Process., 2025, 134, p 547-557.10.1016/j.jmapro.2024.12.077 ↗
16. X.-J. Ning, J.-H. Jang, H.-J. Kim, C.-J. Li and C. Lee, Cold Spraying of Al-Sn Binary Alloy: Coating Characteristics and Particle Bonding Features, Surf. Coat. Technol., 2008, 202(9), p 1681-1687.10.1016/j.surfcoat.2007.07.026 ↗
17. C. Huang, A. List, J. Shen, B. Fu, S. Yin, T. Chen, B. Klusemann, F. Gärtner and T. Klassen, Tailoring Powder Strengths for Enhanced Quality of Cold Sprayed Al6061 Deposits, Mater. Des., 2022, 215(3), p 110494.10.1016/j.matdes.2022.110494 ↗
18. C. Zhang, T. Molla, C. Brandl, J. Watts, R. McCully, C. Tang and G. Schaffer, Cold Spraying of Mixed Metal Powders: A Modelling Framework for Predicting Deposition Efficiency and Coating Composition, J. Therm. Spray Technol., 2025, 34(4), p 1133-1146.10.1007/s11666-025-01967-9 ↗