Effects of Spray Conditions and Heat Treatments on the Physical and Mechanical Properties of Al6061 Deposits Cold-Sprayed Using N2 Gas
Source abstract
Abstract
Understanding the influence of spray conditions and post-spray heat treatments on the performance of cold-sprayed materials using N 2 as the carrier gas is essential. This study examines the impact of various spray conditions and heat treatments on the physical and mechanical properties of cold-sprayed Al6061. Specimens prepared under two different spray conditions, varying the carrier gas temperature, were tested in both their as-sprayed and heat-treated states. Heat treatments, including standard and elevated temperature processes, were applied to enhance mechanical properties. Microstructural characterization was performed by assessing particle bonding quality, deformation behavior, and porosity fraction. Mechanical properties, including the yield and compression strengths, were assessed under both quasi-static compression and high-strain-rate testing at various strain rates. The physical properties, including thermal conductivity (TC), electrical conductivity (EC), and coefficient of thermal expansion (CTE), of specimens prepared under different conditions were evaluated and correlated with their mechanical properties. The results showed that the as-sprayed deposits exhibited inferior mechanical and physical properties compared to wrought Al6061. However, heat treatments improved interparticle bonding and significantly enhanced both the mechanical and physical properties, with values approaching those of wrought Al6061. Specifically, the high-temperature heat treatment performed near the solidus temperature of Al6061 resulted in properties that are closest to those of the wrought material. Statistical analysis of the results indicated strong correlations between the physical properties (TC, EC, CTE) and the compression strength, as well as among these physical properties themselves.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Advanced ceramic materials synthesis · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (62)
Show source-provided references
1. S. Pathak and G. Saha, Development of Sustainable Cold Spray Coatings and 3D Additive Manufacturing Components for Repair/Manufacturing Applications: A Critical Review, Coatings, 2017 https://doi.org/10.3390/coatings708012210.3390/coatings7080122 ↗
2. J. Villafuerte, Modern Cold Spray: Materials, Process, and Applications, Springer, 2015.10.1007/978-3-319-16772-5 ↗
3. S. Yin, P. Cavaliere, B. Aldwell, R. Jenkins, H. Liao, W. Li, and R. Lupoi, Cold Spray Additive Manufacturing and Repair: Fundamentals and Applications, Addit. Manuf., 2018, 21, p 628–650.
4. H. Assadi, F. Gärtner, T. Stoltenhoff, and H. Kreye, Bonding Mechanism in Cold Gas Spraying, Acta Mater., 2003, 51(15), p 4379–4394.10.1016/S1359-6454(03)00274-X ↗
5. V.K. Champagne, The Cold Spray Materials Deposition Process (2007)10.1533/9781845693787 ↗
6. T. Christy, N. Murugan, and S. Kumar, A Comparative Study on the Microstructures and Mechanical Properties of Al 6061 Alloy and the MMC Al 6061/TiB2/12p, J. Miner. Mater. Charact. Eng., 2010, 9(1), p 57–65.
7. F. Rajabi, A. Zarei-Hanzaki, M. Eskandari, and S. Khoddam, The Effects of Rolling Parameters on the Mechanical Behavior of 6061 Aluminum Alloy, Mater. Sci. Eng. A, Struct. Mater. Prop. Microstruct. Process., 2013, 578, p 90–95.10.1016/j.msea.2013.04.023 ↗
8. J.G. Kaufman, Aluminum Alloys, Mechanical Engineers’ Handbook. 2005, p 59–11610.1002/0471777447.ch3 ↗
9. S.E. Julien, A. Nourian-Avval, W. Liang, T. Schwartz, O.C. Ozdemir, and S. Müftü, Bulk Fracture Anisotropy in Cold-Sprayed Al 6061 Deposits, Eng. Fract. Mech., 2022 https://doi.org/10.1016/j.engfracmech.2022.10830110.1016/j.engfracmech.2022.108301 ↗
10. A. Nourian and S. Müftü, Effect of Substrate Surface Finish and Particle Velocity on Fatigue Performance of Cold Spray Coated A6061 Aluminum Alloy, Surf. Coat. Technol., 2022 https://doi.org/10.1016/j.surfcoat.2022.12867610.1016/j.surfcoat.2022.128676 ↗
11. A. Nourian, T. Schwartz, S. Boese, and S. Müftü, Effects of Process Parameters on Cold Spray Deposition of Al-6061 Alloy, J. Therm. Spray Technol., 2022, 31(8), p 2517–2536.10.1007/s11666-022-01456-3 ↗
12. H. Koivuluoto, J. Larjo, D. Marini, G. Pulci, and F. Marra, Cold-Sprayed Al6061 Coatings: Online Spray Monitoring and Influence of Process Parameters on Coating Properties, Coatings, 2020 https://doi.org/10.3390/coatings1004034810.3390/coatings10040348 ↗
13. K.S. Al-Hamdani, J.W. Murray, T. Hussain, and A.T. Clare, Heat-Treatment and Mechanical Properties of Cold-Sprayed High Strength Al Alloys from Satellited Feedstocks, Surf. Coat. Technol., 2019, 374, p 21–31.10.1016/j.surfcoat.2019.05.043 ↗
14. N. Hutasoit, M.A. Javed, R.A.R. Rashid, S. Wade, and S. Palanisamy, Effects of Build Orientation and Heat Treatment on Microstructure, Mechanical and Corrosion Properties of Al6061 Aluminium Parts Built by Cold Spray Additive Manufacturing Process, Int. J. Mech. Sci., 2021 https://doi.org/10.1016/j.ijmecsci.2021.10652610.1016/j.ijmecsci.2021.106526 ↗
15. A. Nourian, C. Beamer, and S. Muftu, Effects of Post-Deposition Processing on Static and Cyclic Performance of Cold Sprayed 6061 Aluminum Alloy, Addit. Manuf., 2024 https://doi.org/10.1016/j.addma.2024.10424610.1016/j.addma.2024.104246 ↗
16. M.R. Rokni, C.A. Widener, O.C. Ozdemir, and G.A. Crawford, Microstructure and Mechanical Properties of Cold Sprayed 6061 Al in as-Sprayed and Heat Treated Condition, Surf. Coat. Technol., 2017, 309, p 641–650.10.1016/j.surfcoat.2016.12.035 ↗
17. G. Sundararajan, N.M. Chavan, and S. Kumar, The Elastic Modulus of Cold Spray Coatings: Influence of Inter-Splat Boundary Cracking, J. Therm. Spray Technol., 2013, 22(8), p 1348–1357.10.1007/s11666-013-0034-5 ↗
18. K.M. Phua, T. Stapel, and T.Y. Ansell, Effect of Heat Treatment on the Mechanical and Tribological Properties of Dual-Reinforced Cold-Sprayed Al Coatings, J. Manuf. Mater. Process., 2023 https://doi.org/10.3390/jmmp701003210.3390/jmmp7010032 ↗
19. R. Sinclair-Adamson, M. Harbidge, and R. Murray, Sintering of Cold Spray Additively Manufactured Aluminum 6061, J. Therm. Spray Technol., 2021, 30(6), p 1493–1511.10.1007/s11666-021-01238-3 ↗
20. S. Boese, A. Sevinsky, A. Nourian-Avval, O. Özdemir, and S. Müftü, Laser Assisted Cold Spray of Aluminum Alloy 6061: Experimental Results, Addit. Manuf., 2024, 95, p 104548.
21. M.-S. Baek, Y.-K. Kim, and K.-A. Lee, Effect of Strain Rate on the Microstructure Evolution and Compressive Deformation Behavior of High-Strength Cu Bulk Material Manufactured by Cold Spray Process, J. Therm. Spray Technol., 2019, 28(5), p 917–929.10.1007/s11666-019-00870-4 ↗
22. Y.-K. Kim, K.-S. Kim, H.-J. Kim, C.-H. Park, and K.-A. Lee, Microstructure and Room Temperature Compressive Deformation Behavior of Cold-Sprayed High-Strength Cu Bulk Material, J. Therm. Spray Technol., 2017, 26(7), p 1498–1508.10.1007/s11666-017-0613-y ↗
23. Y.-K. Kim, and K.-A. Lee, Effect of Carrier Gas Species on the Microstructure and Compressive Deformation Behaviors of Ultra-Strong Pure Copper Manufactured by Cold Spray Additive Manufacturing, J. Mater. Sci. Technol., 2022, 97, p 264–271.10.1016/j.jmst.2021.04.062 ↗
24. B.T. Mengiste, A. Arab, Y. Guo, Y. Lei, X. Li, P. Chen, and J. Xie, Effect of Strain Rate on Compressive Behavior and Deformation Mechanism of CoCrNi Medium Entropy Alloy Fabricated via Cold Spray Additive Manufacturing, J. Alloy. Compd., 2024, 980, p 173627.10.1016/j.jallcom.2024.173627 ↗
25. B.T. Mengiste, A. Arab, Y. Guo, Y. Lei, X. Li, P. Chen, and J. Xie, Tuning the Mechanical Properties of CrCoFeMnNi High Entropy Alloy via Cold Spray Additive Manufacturing Associated with Heat treatment, Mater. Sci. Eng. A, 2024 https://doi.org/10.1016/j.msea.2024.14621410.1016/j.msea.2024.146214 ↗
26. S. Sayahlatifi, Z. Zaiemyekeh, C. Shao, A. McDonald, and J.D. Hogan, Strain Rate-Dependent Behavior of Cold-Sprayed Additively Manufactured Al–Al2O3 Composites: Micromechanical Modeling and Experimentation, Composit. Part B Eng., 2024, 280, p 111479.10.1016/j.compositesb.2024.111479 ↗
27. R. Sinclair-Adamson, V. Luzin, A. Duguid, K. Kannoorpatti, and R. Murray, Residual Stress Distributions in Cold-Sprayed Copper 3D-Printed Parts, J. Therm. Spray Technol., 2020, 29(6), p 1525–1537.10.1007/s11666-020-01040-7 ↗
28. M. Wang, W. Xiong, D. Chang, B. Yu, X. Zhang, and L. Zheng, Effect of Microstructure on Energy Release Characteristics of Al/Ni Energetic Structural Material Prepared by Cold Spraying, Langmuir, 2024, 40(35), p 18619–18630.10.1021/acs.langmuir.4c02146 ↗
29. P. Coddet, C. Verdy, C. Coddet, and F. Debray, On the Mechanical and Electrical Properties of Copper-Silver and Copper-Silver-Zirconium Alloys Deposits Manufactured by Cold Spray, Mater. Sci. Eng. A, 2016, 662, p 72–79.10.1016/j.msea.2016.03.049 ↗
30. Y. Li, Y. Wei, X. Luo, C. Li, and N. Ma, Correlating Particle Impact Condition with Microstructure and Properties of the Cold-Sprayed Metallic Deposits, J. Mater. Sci. Technol., 2020, 40, p 185–195.10.1016/j.jmst.2019.09.023 ↗
31. Y.-J. Li, X.-T. Luo, H. Rashid, and C.-J. Li, A New Approach to Prepare Fully Dense Cu with High Conductivities and Anti-Corrosion Performance by Cold Spray, J. Alloys Compd., 2018, 740, p 406–413.10.1016/j.jallcom.2017.11.053 ↗
32. P. Sudharshan Phani, D. Srinivasa Rao, S.V. Joshi, and G. Sundararajan, Effect of Process Parameters and Heat Treatments on Properties of Cold Sprayed Copper Coatings, J. Therm. Spray Technol., 2007, 16(3), p 425–434.10.1007/s11666-007-9048-1 ↗
33. O. Tazegul, V. Dylmishi, and H. Cimenoglu, Copper Matrix Composite Coatings Produced by Cold Spraying Process for Electrical Applications, Arch. Civ. Mech. Eng., 2016, 16(3), p 344–350.10.1016/j.acme.2016.01.005 ↗
34. B. Yu, J. Tam, W. Li, H.J. Cho, J.G. Legoux, D. Poirier, J.D. Giallonardo, and U. Erb, Microstructural and Bulk Properties Evolution of Cold-Sprayed Copper Coatings After Low Temperature Annealing, Materialia, 2019 https://doi.org/10.1016/j.mtla.2019.10035610.1016/j.mtla.2019.100356 ↗
35. K. Cao, M. Yu, C.M. Liang, and H. Chen, Study on Thermal Conductivity of Cold Sprayed Cu Coating, Surf. Eng., 2020, 36(10), p 1058–1066.10.1080/02670844.2020.1790170 ↗
36. Q. Chen, M. Yu, K. Cao, and H. Chen, Thermal Conductivity and Wear Resistance of Cold Sprayed Cu-Ceramic Phase Composite Coating, Surf. Coat. Technol., 2022 https://doi.org/10.1016/j.surfcoat.2022.12813510.1016/j.surfcoat.2022.128135 ↗
37. S. Kikuchi, S. Yoshino, M. Yamada, M. Fukumoto, and K. Okamoto, Microstructures and Thermal Properties of Cold-Sprayed Cu-Cr Composite Coatings, J. Therm. Spray Technol., 2013, 22(6), p 926–931.10.1007/s11666-013-9926-7 ↗
38. O.C. Ozdemir, P. Schwartz, S. Muftu, F.C. Thompson, G.A. Crawford, A.T. Nardi, V.K. Champagne, and C.A. Widener, High Rate Deposition in Cold Spray, J. Therm. Spray Technol., 2021, 30(1–2), p 344–357.10.1007/s11666-020-01135-1 ↗
39. P. Petrovskiy, M. Doubenskaia, A. Sova, and A. Travyanov, Analysis of Copper-Tungsten Cold Spray Coating: Kinetics of Coating Formation and its Thermal Properties, Surf. Coat. Technol., 2020 https://doi.org/10.1016/j.surfcoat.2020.12537610.1016/j.surfcoat.2020.125376 ↗
40. D. Seo, K. Ogawa, K. Sakaguchi, N. Miyamoto, and Y. Tsuzuki, Parameter Study Influencing Thermal Conductivity of Annealed Pure Copper Coatings Deposited by Selective Cold Spray Processes, Surf. Coat. Technol., 2012, 206(8–9), p 2316–2324.10.1016/j.surfcoat.2011.10.010 ↗
41. F.J. Wei, B.Y. Chou, K.Z. Fung, and S.Y. Tsai, Thermomechanical Properties of Cold-Sprayed Copper Coatings from Differently Fabricated Powders, Surf. Coat. Technol., 2022 https://doi.org/10.1016/j.surfcoat.2022.12812810.1016/j.surfcoat.2022.128128 ↗
42. C. Chen, Y. Xie, L. Liu, R. Zhao, X. Jin, S. Li, R. Huang, J. Wang, H. Liao, and Z. Ren, Cold Spray Additive Manufacturing of Invar 36 Alloy: Microstructure, Thermal Expansion and Mechanical Properties, J. Mater. Sci. Technol., 2021, 72, p 39–51.10.1016/j.jmst.2020.07.038 ↗
43. W.B. Choi, L. Li, V. Luzin, R. Neiser, T. Gnäupel-Herold, H.J. Prask, S. Sampath, and A. Gouldstone, Integrated Characterization of Cold Sprayed Aluminum Coatings, Acta Mater., 2007, 55(3), p 857–866.10.1016/j.actamat.2006.09.006 ↗
44. L. Gyansah, N.H. Tariq, J.R. Tang, X. Qiu, B. Feng, J. Huang, H. Du, J.Q. Wang, and T.Y. Xiong, Cold Spraying SiC/Al Metal Matrix Composites: Effects of SiC Contents and Heat Treatment on Microstructure, Thermophysical and Flexural Properties, Mater. Res. Express, 2018 https://doi.org/10.1088/2053-1591/aaaeee10.1088/2053-1591/aaaeee ↗
45. V. Luzin, K. Spencer, and M.X. Zhang, Residual Stress and Thermo-Mechanical Properties of Cold Spray Metal Coatings, Acta Mater., 2011, 59(3), p 1259–1270.10.1016/j.actamat.2010.10.058 ↗
46. Y.-K. Wei, X.-T. Luo, X. Chu, G.-S. Huang, and C.-J. Li, Solid-State Additive Manufacturing High Performance Aluminum Alloy 6061 Enabled by an In-situ Micro-Forging Assisted Cold Spray, Mater. Sci. Eng. A Struct. Mater. Prop. Microstruct. Process., 2020 https://doi.org/10.1016/j.msea.2020.13902410.1016/j.msea.2020.139024 ↗
47. N. Showaiter and M. Youseffi, Compaction, Sintering and Mechanical Properties of Elemental 6061 Al Powder with and without Sintering Aids, Mater. Des., 2008, 29(4), p 752–762.10.1016/j.matdes.2007.01.027 ↗
48. X.Z. Zhang, T.J. Chen, Y.S. Chen, Y.J. Wang, and H. Qin, Effects of Solution Treatment on Microstructure and Mechanical Properties of Powder Thixoforming 6061 Aluminum Alloy, Mater. Sci. Eng. A, 2016, 662, p 214–226.10.1016/j.msea.2016.03.060 ↗
49. Anonymous, ImageJ: Image Processing and Analysis in Java (Version: 1.54f), 2023
50. Anonymous, ASTM Standard E9-19 Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature
51. S.E. Gustafsson, Transient Plane Source Techniques for Thermal Conductivity and Thermal Diffusivity Measurements of Solid Materials, Rev. Sci. Instrum., 1991, 62(3), p 797–804.10.1063/1.1142087 ↗
52. Anonymous, ASTM E831-25 Standard Test Method for Linear Thermal Expansion of Solid Materials by Thermomechanical Analysis
53. Anonymous, ASTM E-2113 Standard Test Method for Length Change Calibration of Thermomechanical Analyzers
54. N. Biswas, J.L. Ding, V.K. Balla, D.P. Field, and A. Bandyopadhyay, Deformation and Fracture Behavior of Laser Processed Dense and Porous Ti6Al4V Alloy under Static and Dynamic Loading, Mater. Sci. Eng. A, 2012, 549, p 213–221.10.1016/j.msea.2012.04.036 ↗
55. C. Jiang, S. Cai, L. Mao, and Z. Wang, Effect of Porosity on Dynamic Mechanical Properties and Impact Response Characteristics of High Aluminum Content PTFE/Al Energetic Materials, Materials (Basel), 2019 https://doi.org/10.3390/ma1301014010.3390/ma13010140 ↗
56. P. Hidnert and H. Krider, Thermal Expansion of Aluminum and Some Aluminum Alloys, J. Res. Natl. Bur. Stand., 1952, 48(3), p 209–220.10.6028/jres.048.030 ↗
57. D.S. Smith, A. Alzina, J. Bourret, B. Nait-Ali, F. Pennec, N. Tessier-Doyen, K. Otsu, H. Matsubara, P. Elser, and U.T. Gonzenbach, Thermal Conductivity of Porous Materials, J. Mater. Res., 2013, 28(17), p 2260–2272.10.1557/jmr.2013.179 ↗
58. C. Vincent, J.F. Silvain, J.M. Heintz, and N. Chandra, Effect of Porosity on the Thermal Conductivity of Copper Processed by Powder Metallurgy, J. Phys. Chem. Solids, 2012, 73(3), p 499–504.10.1016/j.jpcs.2011.11.033 ↗
59. Z. Yang, J. Xu, Y. Qian, H. Liu, J. Zuo, K. Ma, and M. Li, Electrical Conductivities and Mechanical Properties of Ti3SiC2 Reinforced Cu-Based Composites Prepared by Cold Spray, J. Alloy. Compd., 2023 https://doi.org/10.1016/j.jallcom.2023.16947310.1016/j.jallcom.2023.169473 ↗
60. S. Kumar, S.K. Reddy, and S.V. Joshi, Microstructure and Performance of Cold Sprayed Al-SiC Composite Coatings with High Fraction of Particulates, Surf. Coat. Technol., 2017, 318, p 62–71.10.1016/j.surfcoat.2016.11.047 ↗
61. J.R. Davis, Metals Handbook Desk Edition, ASM international, 1998.10.31399/asm.hb.mhde2.9781627081993 ↗
62. J.R. Davis, ASM Specialty Handbook: Tool Materials, ASM International, 1995