journal article·2026-06-09Open access

Thermomechanical Stress and Damage Evolution Near Film Cooling Holes in Thermal Barrier Coatings: Role of the Bond-Coat Layer

Xiaojie Han, Masayuki Arai

Abstract

Abstract Thermal barrier coatings (TBCs) produced by thermal spray processes and combined with film cooling are widely used to protect gas turbine components under severe thermomechanical environments. In such systems, fatigue cracks and interfacial damage frequently initiate near film cooling holes due to complex stress redistribution within the multilayer architecture consisting of a ceramic top coat (TC), a metallic bond coat (BC), and a substrate. Although the effects of cooling holes have been extensively investigated, the mechanical role of the bond-coat layer in stress and damage evolution under thermomechanical fatigue (TMF) remains insufficiently understood. In this study, a three-dimensional finite element framework is developed to analyze TMF-induced stress redistribution, damage accumulation, and crack initiation and propagation near film cooling holes in an air-plasma-sprayed (APS) TBC system. The model incorporates a damage-coupled inelastic constitutive formulation for the TC, temperature-dependent elastoplasticity for a CoNiCrAlY bond coat, and viscoplastic behavior for an IN738LC substrate, together with a nonlocal crack-propagation algorithm. Both in-phase and out-of-phase TMF loadings are examined over a temperature range representative of cooled TBC regions. The results demonstrate that the bond coat plays a dual mechanical role. Inelastic deformation of the bond coat relaxes stresses in the TC and modifies circumferential stress distributions around the cooling hole, while bond-coat-mediated stress redistribution promotes the accumulation of interfacial delamination strain, particularly under thermally dominated TMF conditions. Crack initiation locations rotate by approximately 90° depending on the dominant loading mode, and a characteristic stress-range threshold separates the fatigue lives under in-phase and out-of-phase conditions. These findings provide mechanistic insight into the role of bond-coat plasticity in damage evolution and durability of thermally sprayed TBC systems with cooling holes.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Advanced ceramic materials synthesis · Turbomachinery Performance and Optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (39)

Show source-provided references
1. A.G. Evans, D.R. Mumm, J.W. Hutchinson, G.H. Meier, and F.S. Pettit, Mechanisms Controlling the Durability of Thermal Barrier Coatings, Prog. Mater. Sci., 2001, 46(5), p 505–553.10.1016/S0079-6425(00)00020-7 ↗
2. N.P. Padture, M. Gell, and E.H. Jordan, Thermal Barrier Coatings for Gas-turbine Engine Applications, Science, 2002, 296(5566), p 280–284.10.1126/science.1068609 ↗
3. D.R. Clarke and C.G. Levi, Materials Design for the Next Generation Thermal Barrier Coatings, Annu. Rev. Mater. Res., 2003, 33, p 383–417.10.1146/annurev.matsci.33.011403.113718 ↗
4. R.J. Goldsein, Film Cooling, Adv. Heat Transf., 1971, 7, p 321–379.10.1016/S0065-2717(08)70020-0 ↗
5. J.C. Han, S. Dutta, and S. Ekkad, Gas Turbine Heat Transfer and Cooling Technology, CRC Press, 2013.
6. D.G. Bogard and K.A. Thole, Gas Turbine Film Cooling, J. Propuls. Power, 2006, 22(2), p 249–270.10.2514/1.18034 ↗
7. M. Tanaka, C. Mercer, Y. Kagawa, and A.G. Evans, Thermomechanical Fatigue Damage Evolution in a Superalloy/Thermal Barrier System Containing a Circular Through Hole, J. Am. Ceram. Soc., 2011, 94(1), p 128–135.
8. D. Qiao and W. Zeng, Numerical Stress Analysis of TBCs at Film Cooling Hole’s Edge Based on TBC-Film Cooling System, J. Therm. Spray Technol., 2024, 33(8), p 2627–2640.10.1007/s11666-024-01863-8 ↗
9. J. Jiang, X. Ma, and B. Wang, Stress Analysis of the Thermal Barrier Coating System Near a Cooling Hole Considering the Free-edge Effect, Ceram. Int., 2020, 46(1), p 331–342.10.1016/j.ceramint.2019.08.267 ↗
10. J.-X. Wang, H.-T. Sun, Q.-T. Gong, F.-X. Li, and Z.-Z. Li, Deformation Prediction Theory of Thermal Barrier Coatings Near Cooling Holes Under Thermal Cycling, ACS Omega, 2023, 8(14), p 13048–13058.10.1021/acsomega.3c00307 ↗
11. E.P. Busso, Z.Q. Qian, M.P. Taylor, and H.E. Evans, The Influence of Bondcoat and Topcoat Mechanical Properties on Stress Development in Thermal Barrier Coating Systems, Acta Mater., 2009, 57(8), p 2349–2361.10.1016/j.actamat.2009.01.017 ↗
12. X. Peng, N. Sridhar, and D.R. Clarke, The Stress Distribution Around Holes in Thermal Barrier Coatings, Mater. Sci. Eng. A, 2004, 380(1–2), p 208–214.10.1016/j.msea.2004.03.062 ↗
13. R.J. Christensen, D.M. Lipkin, and D.R. Clarke, Nondestructive Evaluation of the Oxidation Stresses Through Thermal Barrier Coatings Using Cr3+ Piezospectroscopy, Appl. Phys. Lett., 1996, 69(25), p 3754–3756.10.1063/1.117182 ↗
14. R. Vaßen, A. Stuke, and D. Stöver, Recent Developments in the Field of Thermal Barrier Coatings, J. Therm. Spray Technol., 2009, 18(2), p 181–186.10.1007/s11666-009-9312-7 ↗
15. A.M. Karlsson and A.G. Evans, A Numerical Model for the Cyclic Instability of Thermally Grown Oxides in Thermal Barrier Systems, Acta Mater., 2001, 49(10), p 1793–1804.10.1016/S1359-6454(01)00073-8 ↗
16. I.G. Wright and B.A. Pint, Bond Coating Issues in Thermal Barrier Coatings for Industrial Gas Turbines, Proc. Inst. Mech. Eng. A J. Power Energy, 2005, 219(2), p 101–107.10.1243/095765005X6836 ↗
17. D.R. Clarke, Materials Selection Guidelines for low Thermal Conductivity Thermal Barrier Coatings, Surf. Coat. Technol., 2003, 163, p 67–74.10.1016/S0257-8972(02)00593-5 ↗
18. R.C. Reed, The Superalloys: Fundamentals and Applications, Cambridge Univ. Press, 2006.10.1017/CBO9780511541285 ↗
19. J.W. Hutchinson and Z. Suo, Mixed Mode Cracking in Layered Materials, Adv. Appl. Mech., 1992, 29, p 63–191.10.1016/S0065-2156(08)70164-9 ↗
20. J.W. Hutchinson and A.G. Evans, On the Delamination of Thermal Barrier Coatings in a Thermal Gradient, Surf. Coat. Technol., 2002, 149, p 179–184.10.1016/S0257-8972(01)01451-7 ↗
21. T.A. Cruse, S.E. Stewart, and M. Ortiz, Thermal Barrier Coating Life Prediction Model Development, J. Eng. Gas Turbines Power, 1988, 110(4), p 610–616.10.1115/1.3240179 ↗
22. T.S. Chowdhury, F.T. Mohsin, M.M. Tonni, M.N.H. Mita, and M.M. Ehsan, A Critical Review on Gas Turbine Cooling Performance and Failure Analysis of Turbine Blades, Int. J. Thermofluids, 2023, 18, 100329. https://doi.org/10.1016/j.ijft.2023.10032910.1016/j.ijft.2023.100329 ↗
23. A. Jung and A. Schnell, Crack Growth in a Coated Gas Turbine Superalloy Under Thermo-Mechanical Fatigue, Int. J. Fatigue, 2008, 30, p 286–291.10.1016/j.ijfatigue.2007.01.040 ↗
24. H.L. Bernstein and J.M. Allen, Analysis of Cracked Gas Turbine Blades, J. Eng. Gas Turbines Power, 1992, 114(2), p 293–301.10.1115/1.2906586 ↗
25. L. Zhang, L. Cui, X. Dang, Z. Cao, H. Su, Q. Wang, S. Luo, X. Liang, W. He, and Y. Li, Temperature-Dependent Micro-Mechanisms in Thermomechanical Fatigue of Thermal Barrier Coating/Single-Crystal Superalloy Systems, Corros. Sci., 2026, 258, 113406. https://doi.org/10.1016/j.corsci.2025.11340610.1016/j.corsci.2025.113406 ↗
26. R. Kitawaza, M. Tanaka, Y. Kagawa, and Y.F. Liu, Damage Evolution of TBC System Under in-Phase Thermos-Mechanical Tests, Mater. Sci. Eng. B, 2010, 173(1–3), p 130–134.10.1016/j.mseb.2009.12.022 ↗
27. Z.B. Chen, Z.G. Wang, and S.J. Zhu, Thermomechanical Fatigue Behavior of an Air Plasma Sprayed Thermal Barrier Coating System, Mater. Sci. Eng. A, 2011, 528(29–30), p 8396–8401.10.1016/j.msea.2011.08.031 ↗
28. M. Arai, X. Wu, and K. Fujimoto, Inelastic Deformation of Freestanding Plasma-Sprayed Thermal Barrier Coatings, J. Solid Mech. Mater. Eng., 2010, 4(2), p 221–234. (, 2010.)10.1299/jmmp.4.221 ↗
29. M. Arai, Inelastic Constitutive Equation of Plasma-Sprayed Ceramic Thermal Barrier Coatings, Acta Metall. Sin., 2011, 24(2), p 161–168.
30. M. Arai, Microdamage-Coupled Inelastic Deformation Analysis of Ceramic Thermal Barrier Coatings Subjected to Tensile Loading, Surf. Coat. Technol., 2016, 304, p 542–552.10.1016/j.surfcoat.2016.07.047 ↗
31. M. Arai, H. Katori, and K. Ito, Numerical Simulation of Inelastic Deformation and Crack Propagation in TBC-Multilayered Ni Based Superalloy Subjected to Thermo-Mechanical Loadings, Surf. Coat. Technol., 2020, 399, 126159. https://doi.org/10.1016/j.surcoat.2020.12615910.1016/j.surcoat.2020.126159 ↗
32. X. Han, M. Arai, and Y. Meng, Inelastic Deformation and Fatigue Cracking in TBC Around Film Cooling Hole Subjected to Thermomechanical Loading, J. Therm. Spray Technol., 2025, 34(8), p 3376–3388.10.1007/s11666-025-02106-0 ↗
33. F.J. Cunha, M.T. Dahmer, and M.K. Chyu, Thermal-Mechanical Life Prediction System for Anisotropic Turbine Components, J. Turbomach., 2006, 128(2), p 240–250.10.1115/1.2137740 ↗
34. P.K. Wright and A.G. Evans, Mechanisms governing the performance of thermal barrier coatings, Curr. Opin. Solid State Mater. Sci., 1999, 4(3), p 255–265.10.1016/S1359-0286(99)00024-8 ↗
35. Y. Tamarin, Protective Coatings for Turbine Blades, ASM international.
36. R. Muche and K. Rau, Coupled Thermomechanical Fatigue Tests for Simulating Load Conditions in Cooled Turbine Parts, J. Eng. Gas Turbines Power, 2012, 134(5), 052508. https://doi.org/10.1115/1.400473110.1115/1.4004731 ↗
37. D. Lee, I. Shin, Y. Kim, J.-M. Koo, and C.-S. Seok, A Study on Thermos Mechanical Fatigue Life Prediction of Ni-Base Superalloy, Int. J. Fatigue, 2014, 62, p 62–66.10.1016/j.ijfatigue.2013.10.011 ↗
38. D. Kim, K. Park, K. Kim, C.-S. Seok, J. Lee, and K. Kim, A Method for Predicting the Delamination Life of Thermal Barrier Coatings Under Thermal Gradient Mechanical Fatigue Condition Considering Degradation Characteristics, Int. J. Fatigue, 2021, 151, 106402. https://doi.org/10.1016/j.ijfatigue.2021.10640210.1016/j.ijfatigue.2021.106402 ↗
39. D.-T. Vo, T.-D. Mai, B. Kim, J.-S. Jung, and J. Ryu, Numerical Investigation of Crack Initiation in High-Pressure Gas Turbine Blade Subjected to Thermal-Fluid-Mechanical Low-Cycle Fatigue, Int. J. Heat Mass Transf., 2023, 202, 123748. https://doi.org/10.1016/j.ijheatmasstransfer.2022.12374810.1016/j.ijheatmasstransfer.2022.123748 ↗