Enhancing the machinability of recycled polypropylene composites reinforced with waste cotton and pine sawdust through milling parameters optimization
Source abstract
Abstract
This study investigates the milling behavior of wood-plastic composites (WPCs) made from recycled polypropylene (RPP) reinforced with waste cotton fabric and pine sawdust. The effects of spindle speed (600 rpm, 400 rpm, 200 rpm), feed rate (0.2 mm/rev, 0.4 mm/rev, 0.6 mm/rev), and depth of cut (2.5 mm, 3.0 mm, 3.5 mm) on key response variables—material removal rate (MRR), surface roughness (Ra), machining forces (Fm), and delamination factor (Fd)—were analyzed. ANOVA and Signal-to-Noise Ratio methods were used to evaluate the significance of the parameters, while multi-response optimization was conducted using the Surface Response Optimization Technique. The results showed that spindle speed significantly influenced delamination and surface roughness, while feed rate and depth of cut primarily affected MRR and machining forces. The optimal machining parameters—600 rpm spindle speed, 0.2 mm/rev feed rate, and 3.5 mm depth of cut—achieved an MRR of 23.45 mm 3 /min, Ra of 0.13 µm, Fm of 13.66 N, and Fd of 1.08. The findings underscore the importance of parameter optimization for enhancing machining efficiency and surface quality while demonstrating the potential of these WPCs as sustainable and eco-friendly materials for various applications, particularly in the construction industry.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Natural Fiber Reinforced Composites · Additive Manufacturing and 3D Printing Technologies · Innovations in Concrete and Construction Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Mekelle University
References (45)
Show source-provided references
1. Introduction AN, Callister WD, Rethwisch DG. Mater Sci Eng 2018.
2. 10.1002/pls2.1014510.1002/pls2.10145 ↗
3. 10.1080/15440478.2023.220288610.1080/15440478.2023.2202886 ↗
4. 10.1002/pls2.1016110.1002/pls2.10161 ↗
5. 10.1177/0892705723118631210.1177/08927057231186312 ↗
6. Kartal İ, Selİmoğlu H. Investigation of the mechanical behavior of recycled polypropylene-based composite materials filled with waste cotton and pine sawdust. Int. J. Comput. Exp. Sci. Eng. IJCESEN 2023; 9: 412–418.
7. 10.23960/jsl.v10i2.54710.23960/jsl.v10i2.547 ↗
8. 10.1177/089270571456312510.1177/0892705714563125 ↗
9. 10.1016/j.polymer.2024.12669810.1016/j.polymer.2024.126698 ↗
10. Schwarzkopf MJ Burnard MD Wood-plastic composites — performance and environmental impacts 2016; 19–43.10.1007/978-981-10-0655-5_2 ↗
11. 10.1023/A:102085891064610.1023/A:1020858910646 ↗
12. 10.1051/smdo/202301910.1051/smdo/2023019 ↗
13. 10.1002/pls2.1017310.1002/pls2.10173 ↗
14. 10.1002/pls2.1017210.1002/pls2.10172 ↗
15. Skosana SJ, Khoathane C, Malwela T. Driving towards sustainability: a review of natural fiber reinforced polymer composites for eco-friendly automotive light-weighting. J Thermoplast Compos Mater 2024: 08927057241254324.
16. 10.1177/089270571988909510.1177/0892705719889095 ↗
17. 10.1177/0892705723121148110.1177/08927057231211481 ↗
18. 10.1177/089270571882040310.1177/0892705718820403 ↗
19. Taifor Azeez A. A review of wood plastic composites effect on the environment. J. Babylon Univ. Sci. 2019 vol 360.
20. 10.3390/polym1321367010.3390/polym13213670 ↗
21. 10.1177/089270571877287710.1177/0892705718772877 ↗
22. 10.1177/0892705724124803610.1177/08927057241248036 ↗
23. 10.3390/polym1419420610.3390/polym14194206 ↗
24. Maddah HA. Polypropylene as a promising plastic: a review. Am J Polym Sci 2016; 6: 1–11.
25. 10.1002/app.4506010.1002/app.45060 ↗
26. 10.1016/j.carbpol.2016.10.04410.1016/j.carbpol.2016.10.044 ↗
27. 10.3390/polym1304062610.3390/polym13040626 ↗
28. 10.1016/j.matpr.2020.08.57010.1016/j.matpr.2020.08.570 ↗
29. Kartal İ, Selimoğlu H. Usability of pine sawdust and calcite together as filler in polyester composites. Int. J. Comput. Exp. Sci. Eng. IJCESEN 2023; 9: 267–273.
30. Raj SS, Kannan TK, Kathiresan M, et al. Why not stir casting for polymer composites? Investigations on poly lactic acid based wood plastic composite. Mater Today Proc 2020.
31. Prasanth I, Ravishankar DV, Manzoor Hussain M. Analysis of milling process parameters and their influence on glass fiber reinforced polymer composites (research note). Int J Eng 2017; 30: 1074–1080.
32. 10.1016/j.matdes.2014.11.02410.1016/j.matdes.2014.11.024 ↗
33. 10.1080/15440478.2020.182128310.1080/15440478.2020.1821283 ↗
34. 10.1007/s13369-021-05768-410.1007/s13369-021-05768-4 ↗
35. Kartal İ, Selimoğlu H. Usability of pine sawdust and cotton together as filler in recycled polypropylene composites. Int. J. Comput. Exp. Sci. Eng 2024; 10.
36. 10.1002/pls2.1013310.1002/pls2.10133 ↗
37. 10.1002/pls2.1014110.1002/pls2.10141 ↗
38. 10.1002/pls2.1016610.1002/pls2.10166 ↗
39. Afiqah N, Ismail NF, Fadzly MK, et al. Kenaf composites for automotive components: enhancement in machinability and moldability. Polymers 2019; 1–10.
40. 10.3390/ma1613482510.3390/ma16134825 ↗
41. Azmi H, Haron CHC, Ghani JA, et al. Study on machinability effect of surface roughness in milling kenaf fiber reinforced plastic composite (unidirectional) using response surface methodology. ARPN J Eng Appl Sci 2016; 11.
42. 10.4314/ijest.v5i4.310.4314/ijest.v5i4.3 ↗
43. 10.1177/002199831982637310.1177/0021998319826373 ↗
44. 10.1515/secm-2013-014310.1515/secm-2013-0143 ↗
45. 10.1007/s10924-020-01961-y10.1007/s10924-020-01961-y ↗