Laser-assisted automated tape laying: Effects of placement rate and heated tooling on layer bonding and tensile properties
Source abstract
Abstract
This paper investigates the processing parameters placement rate and tooling temperature of laser-assisted automated tape laying (ATL). Plates with carbon fiber-reinforced polyether ether ketone (CF/PEEK) were produced at 6 m/min, 9 m/min and 18 m/min, and 23°C and 250°C tooling temperature, respectively. Correlations of processing conditions with micrographs, void content, thickness, the degree of crystallinity and the shear strength of the compression shear test, including a fractographic analysis, were derived. Processing conditions that increase the degree of crystallinity were only found to improve the compression shear strength at 6 m/min placement rates, primarily due to a void content below 3.4 % and degree of crystallinity above 26 %. The fractographic analysis derived from the compression shear test revealed a strong correlation between the degree of crystallinity and the size of ductile drawings. In contrast, the transverse tensile test showed no influences on the ATL processing conditions, whereas the tensile strength in fiber direction decreased by 11 % from a placement rate of 6 m/min to 18 m/min. ATL with a 250°C tooling temperature increased the strengths by 14 % compared to those at room temperature. A further tensile strength improvement of 0° and 90° to 1754 MPa and 75 MPa was obtained by a subsequent out-of-autoclave consolidation using vacuum bagging.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Surface Polishing Techniques · 3D IC and TSV technologies · Adhesion, Friction, and Surface Interactions
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Technical University of Munich
Funding
Federal Ministry for Economic Affairs and Climate Action
References (47)
Show source-provided references
1. 10.1016/j.actaastro.2023.06.03410.1016/j.actaastro.2023.06.034 ↗
2. STORT project. https://www.asg.ed.tum.de/en/lcc/news/article/stort-project/ (accessed 5 July 2023).
3. Institute of aerodynamics and flow technology - ATEK flight experiment - propulsion technologies and components of launcher stages. https://www.dlr.de/as/en/desktopdefault.aspx/tabid-194/407_read-58040/ (accessed 5 July 2023).
4. 10.1016/j.procir.2019.09.01510.1016/j.procir.2019.09.015 ↗
5. 10.1177/089270571666251610.1177/0892705716662516 ↗
6. 10.1533/978184569925310.1533/9781845699253 ↗
7. Fricke D, Raps L, Schiel I. Prediction of warping in thermoplastic AFP-manufactured laminates through simulation and experimentation. Adv Manuf Polym Compos Sci 2022; 8: 1–10.
8. 10.1177/08927057970100060410.1177/089270579701000604 ↗
9. 10.1016/j.compositesa.2007.05.00310.1016/j.compositesa.2007.05.003 ↗
10. 10.1177/00219983950290140710.1177/002199839502901407 ↗
11. 10.1177/002199830606016210.1177/0021998306060162 ↗
12. 10.1002/adv.2017710.1002/adv.20177 ↗
13. 10.1177/002199831244181010.1177/0021998312441810 ↗
14. Schäfer PM. Consolidation of carbon fiber reinforced Polyamide 6 tapes using laser-assisted tape placement. Munich: Technical University of Munich (TUM), 2018.
15. 10.1016/j.compositesa.2013.03.00310.1016/j.compositesa.2013.03.003 ↗
16. 10.1016/j.compositesa.2014.08.00610.1016/j.compositesa.2014.08.006 ↗
17. 10.1016/S1359-835X(03)00120-910.1016/S1359-835X(03)00120-9 ↗
18. 10.1016/j.compositesa.2017.02.00810.1016/j.compositesa.2017.02.008 ↗
19. Shadmehri F, Hoa SV, Fortin-Simpson J, et al. Effect of in situ treatment on the quality of flat thermoplastic composite plates made by automated fiber placement (AFP). Adv Manuf Polym Compos Sci 2018; 4: 41–47.
20. 10.1016/S1359-835X(97)00072-910.1016/S1359-835X(97)00072-9 ↗
21. 10.1002/app.4164310.1002/app.41643 ↗
22. 10.1016/j.compositesb.2014.05.02510.1016/j.compositesb.2014.05.025 ↗
23. 10.1016/j.compositesa.2014.10.00310.1016/j.compositesa.2014.10.003 ↗
24. 10.1016/j.compositesa.2020.10616010.1016/j.compositesa.2020.106160 ↗
25. 10.1177/00219983920260160310.1177/002199839202601603 ↗
26. Schledjewski R Schlarb AK. Processing window of CF/PEEK for in-situ consolidation. In: SAMPE Europe International Conference Paris France 2007.
27. 10.1016/j.compstruct.2021.11422310.1016/j.compstruct.2021.114223 ↗
28. 10.1016/j.compositesa.2015.08.00810.1016/j.compositesa.2015.08.008 ↗
29. 10.1016/j.compositesa.2019.02.01110.1016/j.compositesa.2019.02.011 ↗
30. Dreher P Chadwick AR Nowotny S. Optimization of in-situ thermoplastic automated fiber placement process parameters through DoE. In: SAMPE Europe Conference. Nantes France 2019.
31. Schiel I, Raps L, Chadwick AR, et al. An investigation of in-situ AFP process parameters using CF/LM-PAEK. Adv Manuf Polym Compos Sci 2020; 6: 191–197.
32. 10.1016/j.compositesa.2021.10648410.1016/j.compositesa.2021.106484 ↗
33. 10.1016/j.compositesa.2012.04.01010.1016/j.compositesa.2012.04.010 ↗
34. Khan MA. Experimental and simulative description of the thermoplastic tape placement process with online consolidation. Kaiserslautern: Institut für Verbundwerkstoffe, 2010.
35. Fink BK, Gillespie JWJr, Ersoy NB. Thermal degradation effects on consolidation and bonding in the thermoplastic fiber-placement process. Adelphi, MD, USA: Army Research Laboratory. Technical Report ARL-TR-2238. https://apps.dtic.mil/sti/citations/ADA379718 (accessed 10 March 2023).
36. 10.1177/0021998322113767610.1177/00219983221137676 ↗
37. Lamontia MA Gruber MB Systems A et al. Modeling the accudyne thermoplastic in situ ATP process. In: SAMPE Europe Conference Paris France 2009.
38. 10.1016/j.compositesa.2021.10628610.1016/j.compositesa.2021.106286 ↗
39. 10.1016/j.compstruct.2020.11253910.1016/j.compstruct.2020.112539 ↗
40. Zinnecker V Backmann V Stokes-Griffin C et al. Laser-assisted thermoplastic tape placement: effects of the consolidation roller diameter on the wedge peel strength of CF/PA6. In: Sampe Europe Conference Amsterdam Netherlands 2020.
41. Backmann V Drechsler K. Automated fiber placement: relation of compression shear and tensile tests of tape laying and winding. In: Twenty-third international conference on composite materials (ICCM23) Belfast UK 2023.
42. 10.1016/S1359-835X(00)00009-910.1016/S1359-835X(00)00009-9 ↗
43. 10.1177/089270571769778010.1177/0892705717697780 ↗
44. 10.1016/0010-4361(88)90721-510.1016/0010-4361(88)90721-5 ↗
45. 10.1106/XDX9-U8K4-E0PM-70MX10.1106/XDX9-U8K4-E0PM-70MX ↗
46. 10.1002/app.1040610.1002/app.10406 ↗
47. 10.1177/0021998324124058510.1177/00219983241240585 ↗