journal article·2026-04

Optimization of conductive PETG-based composite for strain-sensing prosthetic sockets using 3D printing

Abhishek Raj, Lakshya Bhardwaj, Achint Kumar, Saumang Swarup Sharma, Pushpendra Yadav, Ankit Sahai

Publisher page

Abstract

This work focuses on optimizing the mechanical and electromechanical properties of a 3D-printed strain-sensing prosthetic socket fabricated using a conductive PETG-based composite (P15LT35 G) via Fused Deposition Modelling (FDM). A full factorial design (3 3 ) was implemented to study the influence of nozzle diameter (0.4, 0.5, 0.6 mm), infill pattern (grid, lines, gyroid), and infill density (30%, 50%, 70%) on performance characteristics. The socket was evaluated through tensile, flexural, impact, and compression testing, with the best configuration (0.4 mm nozzle, grid pattern, 70% infill) yielding a peak compressive strength of 25.62 MPa and a flexural strength of 31.72 MPa. Electrical characterization revealed that the optimized sensor exhibited a gauge factor of 1.52 with a nonlinearity coefficient of 4.01 under cyclic loading, indicating stable piezoresistive behavior. The low sensitivity, denoting controlled resistance changes under uniform loading, enhances signal reliability for limb-socket interface monitoring. ANOVA and Response Surface Methodology (RSM) were used to develop predictive models with high significance ( p < .05) and adjusted R 2 values exceeding 95%. The final prosthetic socket design includes embedded sensor paths and ventilation zones, validated through load simulations and experimental tests. The study demonstrates a robust approach for integrating sensing capability within structural components, offering a scalable solution for smart prosthetic systems.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Advanced Sensor and Energy Harvesting Materials · Prosthetics and Rehabilitation Robotics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

, Department of Mechanical Engineering

Indian Institute of Petroleum & Energy

, SRMS College of Engineering and Technology Bareilly

References (36)

Show source-provided references
1. 10.1186/s12984-023-01128-510.1186/s12984-023-01128-5 ↗
2. 10.1177/030936461039708710.1177/0309364610397087 ↗
3. 10.1097/00008526-200601000-0000210.1097/00008526-200601000-00002 ↗
4. 10.1016/j.rvsc.2023.10496010.1016/j.rvsc.2023.104960 ↗
5. 10.1208/s12249-022-02242-810.1208/s12249-022-02242-8 ↗
6. Lestari WD Adyono N Faizin AK et al. Optimization of 3D printed parameters for socket prosthetic manufacturing using the taguchi method and response surface methodology. Results Eng; 21: 101847.10.1016/j.rineng.2024.101847 ↗
7. 10.1038/s41598-024-57454-810.1038/s41598-024-57454-8 ↗
8. Beygi HB, Wong MS. Contemporary and future development of 3D printing technology in the field of assistive technology, orthotics and prosthetics. Can Prosthetics Orthot J 2023; 6: 42225.
9. 10.3390/polym1711146610.3390/polym17111466 ↗
10. Kumar S Advances in additive manufacturing volume — I. 2023.
11. 10.1007/s40964-024-00767-x10.1007/s40964-024-00767-x ↗
12. 10.1007/s12008-023-01718-610.1007/s12008-023-01718-6 ↗
13. Raj A Tyagi B Kapoor A et al. Exploring additive manufacturing parameters for improved tensile strength and functional electrode fabrication. Nature-inspired Metaheuristic Algorithms. Boca Raton: CRC Press pp. 257–283.10.1201/9781003612858-10 ↗
14. Raj A Tyagi B Jain A et al. Using annealing to improve the mechanical properties of 3D-printed PLA parts: an experimental investigation pp. 125–136.10.1007/978-981-96-1647-3_11 ↗
15. 10.1007/s11665-023-08844-y10.1007/s11665-023-08844-y ↗
16. 10.1177/089270571987059510.1177/0892705719870595 ↗
17. 10.1177/0892705725134419710.1177/08927057251344197 ↗
18. Ning F. Additive manufacturing of carbon fiber-reinforced plastic composites using fused deposition modeling : effects of. J Compos Mater 2016; 0: 1–12.
19. Dp-IJED R. Effects of infill patterns on time, surface roughness and tensile strength in 3D printing. rjwave.orgDM PatelInt J Eng Dev Res, 2017•rjwave.org 2017; 5. https://rjwave.org/ijedr/papers/IJEDR1703083.pdf
20. 10.1007/s11665-021-05578-710.1007/s11665-021-05578-7 ↗
21. Dikicier S. Additive manufacturıng techniques used in prosthetic treatments. International Journal of Oral and Dental Health. 2024; 10: 163.
22. 10.1007/s00289-025-05719-110.1007/s00289-025-05719-1 ↗
23. 10.1177/089270571243957110.1177/0892705712439571 ↗
24. Barhate AR, Gangadhar SA, Bhandari AJ, et al. Materials used in maxillofacial prosthesis: a review. Pravara Med Rev 2015; 7: 5–8.
25. 10.1016/j.medengphy.2004.08.01510.1016/j.medengphy.2004.08.015 ↗
26. 10.1177/030936461350119010.1177/0309364613501190 ↗
27. 10.4015/S101623721650022810.4015/S1016237216500228 ↗
28. Ionescu RN Totan AR Imre MM et al. Prosthetic materials used for implant-supported restorations and their biochemical oral interactions: a narrative review. Materials; 15(3): 1016.10.3390/ma15031016 ↗
29. 10.1007/s12008-022-00857-610.1007/s12008-022-00857-6 ↗
30. Tyagi B Raj A Sahai A et al. Enhancing compressive strength in polymer composites utilized for application of foot prostheses. J Polym Res 2024; 31(2): 30.10.1007/s10965-024-03880-1 ↗
31. 10.1007/s40964-024-00945-x10.1007/s40964-024-00945-x ↗
32. 10.1177/0892705722110285710.1177/08927057221102857 ↗
33. 10.1177/0892705724126131410.1177/08927057241261314 ↗
34. 10.1177/0892705723118802510.1177/08927057231188025 ↗
35. 10.1007/s12541-025-01229-210.1007/s12541-025-01229-2 ↗
36. 10.1177/0892705724128331210.1177/08927057241283312 ↗