Critical length prediction for fiber breaking in injection molded of long-fiber reinforced thin-walled products
Source abstract
Abstract
Fiber length is one of the vital factors in determining the properties of long fiber reinforced thermoplastics (LFRT). However, many factors may generate fiber breakage in the injection molding process of LFRT, such as friction, melt shear, injection rate, etc. Especially for thin-walled products, owing to the relatively narrow mold cavity and frozen layer near the mold wall, it’s usually difficult for the fibers to move freely with the melt, leading to fiber breakage under the shear stress of the flow field eventually. In such a situation, the existing buckling breakage model based on the assumption fibers immersed in the flow field being in an unconstrained state is no longer applicable. In this paper, a new model for calculating the critical length of constrained fiber in thin-walled injection molded products is developed. A typical long glass fiber reinforced polypropylene thin-walled product was employed to verify the reliability of the model. The high-precision fiber length analyzer was used to calculate the fiber length distribution at different distances from the injection port. At the same time, the length distribution at the corresponding position was predicted via the model. The average prediction accuracy in the three sampling sections is 87.8%, 91.4% and 83.6%, respectively. The results show that the proposed model can effectively predict the fiber length distribution of injection molded thin-walled products. This conclusion provides important support for further accurate calculation of the mechanical properties of products.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Composite Material Mechanics · Additive Manufacturing and 3D Printing Technologies · Injection Molding Process and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
National Engineering Research Center for Advanced Polymer Processing Technology, Zhengzhou University, Zhengzhou China
Yaoshan laboratory, Pingdingshan University, Pingdingshan, China
Shenzhen Silver Basis Technology Co., Ltd., Shenzhen, China
Funding
National Key R&D Program of China · Shenzhen Science and Technology Program · Open Fund of Yaoshan Laboratory · Major Research and Development Projects of Ningbo
References (34)
Show source-provided references
1. 10.1007/s42114-021-00407-w10.1007/s42114-021-00407-w ↗
2. 10.1002/pc.2613810.1002/pc.26138 ↗
3. 10.1063/5.005869310.1063/5.0058693 ↗
4. 10.1007/s11595-020-2300-y10.1007/s11595-020-2300-y ↗
5. 10.1016/j.polymertesting.2022.10779710.1016/j.polymertesting.2022.107797 ↗
6. 10.1080/13588265.2020.175758310.1080/13588265.2020.1757583 ↗
7. 10.1016/j.geits.2022.10004310.1016/j.geits.2022.100043 ↗
8. Li N, Li X, Yao A, et al. Effect fiber length on mechanical and thermal properties of glass fiber reinforced polyphenylene sulfide composite. J Reinforc Plast Compos 2024: 07316844241232960.
9. 10.1016/j.conbuildmat.2022.12702410.1016/j.conbuildmat.2022.127024 ↗
10. 10.1061/JMCEE7.MTENG-1688310.1061/JMCEE7.MTENG-16883 ↗
11. Li Z, Wang J, Wu A, et al. Preparation and properties of hybrid specific length carbon fiber thermoplastic composites by suspension method. Polym Compos 2024: 28318.
12. 10.1177/0954008321105948710.1177/09540083211059487 ↗
13. 10.3390/polym1315249210.3390/polym13152492 ↗
14. 10.1002/pen.2525410.1002/pen.25254 ↗
15. 10.1515/polyeng-2020-012010.1515/polyeng-2020-0120 ↗
16. 10.1002/pen.2638810.1002/pen.26388 ↗
17. Yang J, Li C, Zhang L, et al. Effect of screw configuration and screw speed on mechanical and rheological properties of glass fiber reinforced polyamide 66. Polym Mater Sci Eng 2010; 26(10): 118–121.
18. Li M. Study on injection molding of long glass fiber reinforced polypropylene[D]. Beijing: Beijing University of Chemical Technology, 2018.
19. Zhou H, Li F, Li R, et al. Research on the effect of injection molding process on the properties and appearance of long glass fiber reinforced polypropylene. China Plast Ind 2018; 46(5): 85–88.
20. 10.1007/s12289-008-0263-110.1007/s12289-008-0263-1 ↗
21. 10.1016/j.compositesa.2012.12.01110.1016/j.compositesa.2012.12.011 ↗
22. 10.1016/j.compositesa.2017.07.00910.1016/j.compositesa.2017.07.009 ↗
23. 10.1016/j.compscitech.2016.08.00710.1016/j.compscitech.2016.08.007 ↗
24. 10.1016/j.compscitech.2019.10774910.1016/j.compscitech.2019.107749 ↗
25. 10.1016/j.compositesb.2023.11055910.1016/j.compositesb.2023.110559 ↗
26. 10.1016/j.compositesa.2019.10551410.1016/j.compositesa.2019.105514 ↗
27. 10.1177/073168442091564310.1177/0731684420915643 ↗
28. 10.1016/j.compscitech.2021.10914910.1016/j.compscitech.2021.109149 ↗
29. 10.1016/j.compscitech.2023.11014610.1016/j.compscitech.2023.110146 ↗
30. 10.1007/978-94-011-0195-0_910.1007/978-94-011-0195-0_9 ↗
31. Zhuang J, Wang M, Yu T. Study on the effects of wall slip on melt filling flow in micro injection molding. China Mech Eng 2007; 18(16): 1995–1999.
32. 10.1016/j.compositesa.2020.10611210.1016/j.compositesa.2020.106112 ↗
33. 10.1016/S0266-3538(99)00132-310.1016/S0266-3538(99)00132-3 ↗
34. 10.1016/0924-0136(95)01842-510.1016/0924-0136(95)01842-5 ↗