journal article·2025-09Open access

Localised heating of carbon fibre reinforced thermoplastic tubes in rotary draw bend forming process

Mengyuan Li, Chris Stokes-Griffin, Silvano Sommacal, John Holmes, Paul Compston

Abstract

This paper presents a localised heating technique using an induction heater and a steel spring mandrel for post-forming of polyamide six carbon (CF/PA6) thermoplastic tubes. During heating, the mandrel is heated up more rapidly than the tube to catalyse tube heating to its formable temperature of 220°C. Upon heating, the tube matrix softens to enable fibre movements when a tube undergoes rotary draw bending (RDB), forming the desired curvature. Four sets of [±60°]₄ CF/PA6 tubes were formed using an induction heater incorporated RDB setup into 45°, 90°, 135°, and 180° bends with a bending ratio of 2. Optical characterisation and micro-computed tomography were performed to analyse tube fibre angle and geometry changes. Results suggest that the presented technique is capable of producing tube bends with significant improvements in efficiency and quality as compared to oven and infrared heating, opening up the potential for rapid post-forming of composite tubes for high performance applications.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Laser and Thermal Forming Techniques · Mechanical Behavior of Composites · Mechanical and Thermal Properties Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Materials Physics, Research School of Physics, Australian National University, Canberra, ACT, Australia

Funding

ARC Training Centre for Automated Manufacture of Advanced Composites

References (34)

Show source-provided references
1. 10.1016/j.repl.2021.06.00110.1016/j.repl.2021.06.001 ↗
2. 10.1016/j.compositesb.2022.11046310.1016/j.compositesb.2022.110463 ↗
3. Goodarzi M. Study on the shear bending process of circular tubes 2007; 145.
4. 10.1016/S0034-3617(03)00728-810.1016/S0034-3617(03)00728-8 ↗
5. 10.1016/j.compstruct.2023.11711910.1016/j.compstruct.2023.117119 ↗
6. 10.1299/jsmea.46.42610.1299/jsmea.46.426 ↗
7. 10.1016/S0026-0576(13)70159-410.1016/S0026-0576(13)70159-4 ↗
8. 10.1016/j.jmsy.2021.10.01510.1016/j.jmsy.2021.10.015 ↗
9. Schäfer J, Gries T. 17 - braiding pultrusion of thermoplastic composites. In: Kyosev Y (ed). Advances in Braiding Technology. Woodhead Publishing, 2016, pp. 405–428.
10. 10.1016/j.repl.2015.01.00410.1016/j.repl.2015.01.004 ↗
11. 10.1016/B978-0-12-819496-6.00001-410.1016/B978-0-12-819496-6.00001-4 ↗
12. 10.1016/B978-0-08-100789-1.00001-010.1016/B978-0-08-100789-1.00001-0 ↗
13. 10.1016/j.procir.2019.09.00310.1016/j.procir.2019.09.003 ↗
14. 10.1063/1.496358410.1063/1.4963584 ↗
15. 10.1016/j.compstruct.2014.05.03710.1016/j.compstruct.2014.05.037 ↗
16. 10.1002/pc.1059610.1002/pc.10596 ↗
17. 10.1016/j.matdes.2016.12.01310.1016/j.matdes.2016.12.013 ↗
18. Stokes-Griffin CM, Compston P. Laser-assisted tape placement of thermoplastic composites: the effect of process parameters on bond strength. Proc 5th Int Conf ICSAT 2013 2014; 133–141.
19. 10.1016/j.compositesa.2014.08.00610.1016/j.compositesa.2014.08.006 ↗
20. Engel B, Böcking J. Bending of fibre-reinforced thermoplastic tubes. 20th International Conference on Composite Materials, 2015; 9.
21. Garthaus C Barfuss D Witschel B et al. Tape braiding: high-performance fibre-reinforced thermoplastic profile structures 2015; 52: 62–64.
22. 10.1016/j.compositesa.2022.10694810.1016/j.compositesa.2022.106948 ↗
23. Eckardt S, Barfuß D, Condé-Wolter J, et al. Study on bend-forming behaviour of thermoplastic tape-braided CFRTP profiles. SAMPE Europe Conference 2020, 2020, p. 9.
24. 10.4028/p-fxk5d910.4028/p-fxk5d9 ↗
25. Banno T, Rashidi A, Crawford B, et al. Development of bend-forming technologies on CFRTP tube. Twenty-Second International Conference on Composite Materials, 2019, p. 6.
26. Li M, Stokes-Griffin C, Compston P. Comparative study on the heating methods in the post-forming of carbon reinforced thermoplastic tubular structures. Composites meet Sustainability - Proceedings of the 20th European Conference on Compoite Materials. Lausanne, 2022, pp. 472–479.
27. 10.1016/j.compositesa.2019.02.01110.1016/j.compositesa.2019.02.011 ↗
28. 10.1016/j.compositesa.2020.10595310.1016/j.compositesa.2020.105953 ↗
29. 10.1016/S0266-3538(98)00184-510.1016/S0266-3538(98)00184-5 ↗
30. Mühlbauer A. History of induction heating and melting. Vulkan-Verlag GmbH, 2008.
31. Moosbrugger C. ASM ready reference: electrical and magnetic properties of metals. ASM International, 2000.
32. 10.1007/s10443-024-10234-z10.1007/s10443-024-10234-z ↗
33. Myers GR, Kingston AM, Latham SJ, et al. In: Stock SR, Müller B, Wang G (eds). Rapidly converging multigrid reconstruction of cone-beam tomographic data. San Diego, California, United States, 2016, p. 99671.
34. 10.1016/j.compositesa.2019.04.02910.1016/j.compositesa.2019.04.029 ↗