journal article·2025-04Open access

Rotary ultrasonic drilling of polyetherimide composite to enhance the surface roughness and MRR: Experimental investigations and statistical approach

Abhinav Shard, Vishal Gupta, Mohinder Pal Garg

Abstract

Polyetherimide Composite (PEC) is among the least dense and most compliant materials which possesses the properties of high heat resistance, durability, resistant to wear and corrosion as well as better tribological characteristics. These outstanding properties lead to its diverse applications in automobiles, aerospace, robots, sports equipment. PEC is machined by the conventional machining techniques like cutting, drilling, power hacksaw etc. Some of the limitations observed in conventional machining of these such as tool jamming, damage to surface topology, and fibres. To overcome the aforesaid limitations, in this work attempts to introduce rotary ultrasonic drilling (RUD) as viable option for machining of PEC. This work carries out the investigational study of input control factors on material removal rate (MRR) and surface roughness (SR). The outcomes of the study reveal that the with right selection of drilling control factors, better quality holes with superior topography as compared to conventional drilling, good surface finish, small exit chip sizes, low overcut errors are obtained. Interacting levels of higher spindle speed and a lower feed rate generated better surface characteristics. While drilling with the RUD as compared to normal drilling, there is a drop of 59.01 % at 550 rpm and 60 .9 % at 2550 rpm in SR.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced machining processes and optimization · Advanced Machining and Optimization Techniques · Advanced Surface Polishing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Central Institute of Hand Tools

Thapar Institute of Engineering and Technology

Punjab Engineering College (Deemed to be University)

References (68)

Show source-provided references
1. 10.1177/089270571984454610.1177/0892705719844546 ↗
2. Lin T, Xu J, Ji M, et al. Drilling performance of uncoated brad spur tools for high-strength carbon fiber-reinforced polymer laminates. Proc Inst Mech Eng Part L 2021; 235: 1879–1889.
3. Kumar D, Singh KK. Investigation of delamination and surface quality of machined holes in drilling of multiwalled carbon nanotube doped epoxy/carbon fiber reinforced polymer nanocomposite. Proc Inst Mech Eng Part L 2019; 233: 647–663.
4. 10.1016/j.compositesb.2016.10.01510.1016/j.compositesb.2016.10.015 ↗
5. 10.1016/j.compositesb.2012.10.03810.1016/j.compositesb.2012.10.038 ↗
6. 10.1016/j.compositesa.2013.09.00210.1016/j.compositesa.2013.09.002 ↗
7. 10.1016/j.compstruct.2011.11.02410.1016/j.compstruct.2011.11.024 ↗
8. 10.1115/1.403105210.1115/1.4031052 ↗
9. 10.1016/j.compositesb.2013.06.04210.1016/j.compositesb.2013.06.042 ↗
10. 10.1016/j.ijmachtools.2005.05.02310.1016/j.ijmachtools.2005.05.023 ↗
11. 10.1115/1.402652610.1115/1.4026526 ↗
12. 10.1016/S0261-3069(03)00062-110.1016/S0261-3069(03)00062-1 ↗
13. 10.1007/s12541-021-00596-w10.1007/s12541-021-00596-w ↗
14. 10.1007/s12541-015-0222-y10.1007/s12541-015-0222-y ↗
15. 10.1016/j.ultras.2012.08.00710.1016/j.ultras.2012.08.007 ↗
16. Singh RP, Singhal S. Rotary ultrasonic machining of advanced materials. Review 2015; 2: 777–785.
17. 10.1016/j.ultras.2013.09.00510.1016/j.ultras.2013.09.005 ↗
18. Sindhu D Thakur L. Rotary ultrasonic machining of hard to machine materials- A review. IJERA; 4.
19. Cong WL Pei ZJ Deines TW et al. Rotary ultrasonic machining of CFRP/Ti stacks using variable feedrate. 2013. DOI: 10.1016/j.compositesb.2013.04.022.10.1016/j.compositesb.2013.04.022 ↗
20. Churi N. Rotary ultrasonic machining of hard-to-machine. PhD Thesis, Manhattan, Kansas: Kansas State University, 2010, pp. 1–166.
21. 10.1080/10910344.2012.69896210.1080/10910344.2012.698962 ↗
22. 10.1007/s40430-017-0953-z10.1007/s40430-017-0953-z ↗
23. 10.1007/s40430-018-1524-710.1007/s40430-018-1524-7 ↗
24. 10.1007/s40430-020-02449-510.1007/s40430-020-02449-5 ↗
25. Agarwal R Gupta V Jain V. A novel technique of harvesting cortical bone grafts during orthopaedic surgeries. J Braz Soc Mech Sci Eng; 43. DOI: 10.1007/s40430-021-03064-8.10.1007/s40430-021-03064-8 ↗
26. 10.1016/j.ultras.2014.03.01210.1016/j.ultras.2014.03.012 ↗
27. 10.1016/j.ultras.2019.04.00410.1016/j.ultras.2019.04.004 ↗
28. Singh RP, Singhal S. Experimental study on rotary ultrasonic machining of alumina ceramic: microstructure analysis and multi-response optimization. Proc Inst Mech Eng Part L 2018; 232: 967–986.
29. Singh RP, Singhal S. Experimental investigation of machining characteristics in rotary ultrasonic machining of quartz ceramic. Proc Inst Mech Eng Part L 2018; 232: 870–889.
30. Zhu X, Lin B, Liu L. Efficiency-based compensations and the mechanical load dependencies of rotary transformer for rotary ultrasonic machining applications. Wiley, 2015, vol 8, pp. 986–993.
31. 10.1016/j.ultras.2015.11.00210.1016/j.ultras.2015.11.002 ↗
32. 10.1016/j.jallcom.2016.12.27510.1016/j.jallcom.2016.12.275 ↗
33. 10.1007/s00170-019-03433-710.1007/s00170-019-03433-7 ↗
34. 10.1080/10426914.2016.114018810.1080/10426914.2016.1140188 ↗
35. 10.1080/10426914.2016.117619010.1080/10426914.2016.1176190 ↗
36. 10.1080/1091034060090212410.1080/10910340600902124 ↗
37. Wang P, Jia Y, Li Y, et al. Microstructural, mechanical and tribological performances of copper foam modified CFRP composite for pantograph strip. J Appl Polym Sci 2021; 138: 1–11.
38. 10.1002/app.5136510.1002/app.51365 ↗
39. 10.1177/0731684422112204110.1177/07316844221122041 ↗
40. 10.1177/0954406222111046610.1177/09544062221110466 ↗
41. 10.1016/j.compositesa.2023.10796210.1016/j.compositesa.2023.107962 ↗
42. 10.1177/0731684423121894210.1177/07316844231218942 ↗
43. Morkavuk S Aslantaş K Gemi L et al. The influence of drilling-induced damages and hole quality on hoop tensile and fatigue behavior of CFRP tubes. Compos Part A Appl Sci Manuf; 179. DOI: 10.1016/j.compositesa.2024.108005.10.1016/j.compositesa.2024.108005 ↗
44. 10.1007/s00170-022-10297-x10.1007/s00170-022-10297-x ↗
45. 10.1177/0892705724126480310.1177/08927057241264803 ↗
46. 10.1007/s11668-020-00943-510.1007/s11668-020-00943-5 ↗
47. 10.1016/j.apacoust.2022.10916310.1016/j.apacoust.2022.109163 ↗
48. 10.1177/0892705722114285410.1177/08927057221142854 ↗
49. 10.1177/095440541667311510.1177/0954405416673115 ↗
50. 10.1177/089270571879981610.1177/0892705718799816 ↗
51. 10.1177/0892705721105232510.1177/08927057211052325 ↗
52. 10.1177/073168441246491310.1177/0731684412464913 ↗
53. Wang H, Ning F, Hu Y, et al. Surface grinding of carbon fiber-reinforced plastic composites using rotary ultrasonic machining: effects of tool variables. Adv Mech Eng 2016; 8: 14.
54. 10.1016/j.ijmachtools.2011.10.00710.1016/j.ijmachtools.2011.10.007 ↗
55. 10.1177/073168441142741910.1177/0731684411427419 ↗
56. 10.1016/S1359-835X(99)00065-210.1016/S1359-835X(99)00065-2 ↗
57. 10.1016/0020-7357(79)90019-210.1016/0020-7357(79)90019-2 ↗
58. 10.1007/s40430-022-03608-610.1007/s40430-022-03608-6 ↗
59. Shard A, Agarwal R, Garg MP, et al. In-situ temperature monitoring during rotary ultrasonic-assisted drilling of fiber-reinforced composites. J Thermoplast Compos Mater 2022: 08927057221142854.
60. 10.1016/j.ijmachtools.2005.01.03410.1016/j.ijmachtools.2005.01.034 ↗
61. 10.1007/s00170-017-1468-610.1007/s00170-017-1468-6 ↗
62. 10.1177/168781401560632910.1177/1687814015606329 ↗
63. 10.1007/s00170-017-1401-z10.1007/s00170-017-1401-z ↗
64. Shahabaz SM Shetty N Shetty SD et al. Surface roughness analysis in the drilling of carbon fiber/epoxy composite laminates using hybrid Taguchi-Response experimental design. Mater Res Express; 7. Epub ahead of print 2020 DOI: 10.1088/2053-1591/ab6198.10.1088/2053-1591/ab6198 ↗
65. 10.1016/j.jmrt.2014.10.00310.1016/j.jmrt.2014.10.003 ↗
66. 10.1177/089270572093916310.1177/0892705720939163 ↗
67. 10.1504/IJMTM.2005.00683010.1504/IJMTM.2005.006830 ↗
68. 10.1504/IJMTM.2007.01415410.1504/IJMTM.2007.014154 ↗