Effects of molding on property of thermally conductive and electrically insulating polyamide 6–based composite
Source abstract
Abstract
Thermally conductive and electrically insulating polyamide 6 (PA6) matrix quaternary composites were prepared by hot press molding and injection molding, respectively. The quaternary composites were composed of zero-dimensional aluminum oxide particle, one-dimensional silicon carbide whisker, two-dimensional flake graphite, and PA6 resin matrix. Morphology, structure, density, thermal conductivity, volume electrical resistivity, and tensile strength of two types of composites were characterized by scanning electron microscopy, X-ray diffractometer, thermal conductivity tester, high resistance micro-current tester, and tensile tester. The results showed that crystallinity, thermal conductivity, density, and tensile strength of hot press molding samples were superior to those of samples made by injection molding method. This is due to that hot press molding method can provide higher molding pressure and longer annealing time than injection molding. The mechanism could be explained that the performances of the composites were promoted by increasing molding pressure and annealing time.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Dielectric materials and actuators · Electromagnetic wave absorption materials · Carbon Nanotubes in Composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
State Key Laboratory of Environment-friendly Energy Materials, School of Materials Science and Engineering, Southwest University of Science and Technology, Mianyang, China
Institute of System Engineering, China Academy of Engineering Physics, Sichuan, China
Funding
Project Supported by Scientific Research Fund of Sichuan Provincial Education Department
References (27)
Show source-provided references
1. 10.1002/app.2547910.1002/app.25479 ↗
2. 10.1016/j.synthmet.2004.05.00710.1016/j.synthmet.2004.05.007 ↗
3. 10.1016/j.compscitech.2006.12.01410.1016/j.compscitech.2006.12.014 ↗
4. 10.1016/j.applthermaleng.2015.01.05610.1016/j.applthermaleng.2015.01.056 ↗
5. 10.1016/j.solmat.2017.08.02510.1016/j.solmat.2017.08.025 ↗
6. 10.1016/j.compositesa.2017.07.02110.1016/j.compositesa.2017.07.021 ↗
7. Yang N · Polym Mater Sci Eng · 2017 · 33 · 153
8. 10.1038/srep1939410.1038/srep19394 ↗
9. 10.1109/TDEI.2016.773683610.1109/TDEI.2016.7736836 ↗
10. 10.1016/j.compositesb.2017.02.00810.1016/j.compositesb.2017.02.008 ↗
11. 10.1016/j.carbon.2009.11.04010.1016/j.carbon.2009.11.040 ↗
12. 10.1016/j.compscitech.2003.11.00710.1016/j.compscitech.2003.11.007 ↗
13. 10.1016/j.compositesa.2009.04.00510.1016/j.compositesa.2009.04.005 ↗
14. 10.1016/S1359-835X(01)00107-510.1016/S1359-835X(01)00107-5 ↗
15. 10.1016/S1359-835X(01)00023-910.1016/S1359-835X(01)00023-9 ↗
16. 10.1016/j.compositesa.2005.07.00610.1016/j.compositesa.2005.07.006 ↗
17. Cunha AM, Reis RL, Ferreira FG et al. The influence of processing conditions on the mechanical behavior of UHMWPE/HA and PMMA/HA composites. Alphen aan den Rijn: Kluwer Academic, 1994, pp. 163–176.10.1007/978-94-011-0157-8_11 ↗
18. 10.1016/j.matdes.2009.03.01110.1016/j.matdes.2009.03.011 ↗
19. 10.1016/S0924-0136(98)00422-110.1016/S0924-0136(98)00422-1 ↗
20. 10.1016/0032-3861(87)90035-810.1016/0032-3861(87)90035-8 ↗
21. 10.1002/app.2660310.1002/app.26603 ↗
22. 10.1002/app.1994.07051041310.1002/app.1994.070510413 ↗
23. 10.1002/app.1985.07030053410.1002/app.1985.070300534 ↗
24. 10.1002/app.1993.07049091410.1002/app.1993.070490914 ↗
25. 10.1007/BF0065876210.1007/BF00658762 ↗
26. 10.1002/app.1991.07043061210.1002/app.1991.070430612 ↗
27. 10.1111/j.1151-2916.1988.tb05791.x10.1111/j.1151-2916.1988.tb05791.x ↗