journal article·2022-11

Design and verification of enhanced CFRTPCs fabrication technique using fused deposition modeling

Ali Bin Naveed, Shahid Ikramullah Butt, Aamir Mubashar, Fausz Naeem Chaudhry, Najam ul Qadir, Zhang Faping

Publisher page

Abstract

Research shows that mechanical properties of parts produced using fused deposition modeling (FDM) are inferior when compared to parts produced using conventional techniques such as injection molding. Efforts have been made in recent years to improve mechanical properties by reinforcing the parts with high strength fibers. This has been achieved by either modifying FDM setups to extrude fibers with thermoplastics and fabricate continuous fiber reinforced thermoplastic composites (CFRTPCs) or employing manual techniques subsequent to part production. Existing CFRTPCs fabrication procedures have limitations of fiber exposure to environment, no direct control method for volume fraction, and poor surface finish. This research work is focused on improving the process of producing CFRTPCs by addressing these limitations using a dual extruder FDM setup. The process developed was tested for its feasibility using Kevlar fiber as reinforcement for commercially available ABS, PLA, PLA-C, and PLA-Cu thermoplastic fibers. Taguchi L 16 orthogonal array was used to design experiments, while tensile and flexural testing was performed to determine mechanical properties achieved. Tensile strength was improved up to 3 times the baseline value of thermoplastics, while flexural strength was improved up to 1.6 times. This technique can further the goal of developing CFRTPCs, on industrial level, using FDM with better control over volume fraction and fiber layup.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Manufacturing Process and Optimization · Innovations in Concrete and Construction Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Design and Manufacturing Engineering Department, NUST, School of Mechanical and Manufacturing Engineering, Islamabad, Pakistan

School of Mechanical Engineering, Beijing Institute of Technology, Beijing, China

References (38)

Show source-provided references
1. 10.1023/A:100895612677510.1023/A:1008956126775 ↗
2. 10.1016/S0007-8506(07)61136-610.1016/S0007-8506(07)61136-6 ↗
3. Noorani R · 2006
4. 10.1016/j.matdes.2009.06.01610.1016/j.matdes.2009.06.016 ↗
5. 10.1177/002199831769265910.1177/0021998317692659 ↗
6. 10.1016/S1526-6125(04)70071-710.1016/S1526-6125(04)70071-7 ↗
7. 10.1007/s40430-013-0111-110.1007/s40430-013-0111-1 ↗
8. Onwubolu GC · Int J Manuf Eng · 2014 · 2014
9. 10.1007/s40964-015-0002-310.1007/s40964-015-0002-3 ↗
10. 10.14311/AP.2015.55.035910.14311/AP.2015.55.0359 ↗
11. 10.1016/j.matdes.2017.03.06510.1016/j.matdes.2017.03.065 ↗
12. Tanoto YY · 2017
13. 10.1016/j.promfg.2017.07.07610.1016/j.promfg.2017.07.076 ↗
14. 10.1016/S0921-5093(00)01810-410.1016/S0921-5093(00)01810-4 ↗
15. 10.1007/s11668-014-9803-910.1007/s11668-014-9803-9 ↗
16. 10.1177/002199831664616910.1177/0021998316646169 ↗
17. El Magri A · J Thermoplast Compos Mater
18. Ahmed SW · J Thermoplast Compos Mater
19. 10.1016/j.jmatprotec.2016.07.02510.1016/j.jmatprotec.2016.07.025 ↗
20. 10.1016/j.matdes.2017.10.00710.1016/j.matdes.2017.10.007 ↗
21. 10.1038/srep2305810.1038/srep23058 ↗
22. 10.1016/j.compositesa.2016.05.03210.1016/j.compositesa.2016.05.032 ↗
23. 10.1108/RPJ-08-2015-009810.1108/RPJ-08-2015-0098 ↗
24. 10.1016/j.matdes.2015.10.12310.1016/j.matdes.2015.10.123 ↗
25. 10.1016/j.addma.2018.04.03910.1016/j.addma.2018.04.039 ↗
26. 10.1016/j.addma.2017.06.00410.1016/j.addma.2017.06.004 ↗
27. 10.1016/j.matdes.2017.10.02110.1016/j.matdes.2017.10.021 ↗
28. Barbero EJ · 2017
29. Ross PJ · 1996
30. Roy RK · 1990
31. ASTM International · 2007
32. ASTM International · 2015
33. ASTM International · 2003
34. ASTM International. Standard test method for tensile properties of plastics. Annual book of ASTM standards. D638–08. West Conshohocken: ASTM International, 2009, 8.
35. 10.1016/j.ijpe.2018.02.00310.1016/j.ijpe.2018.02.003 ↗
36. 10.1016/j.compstruct.2011.01.00210.1016/j.compstruct.2011.01.002 ↗
37. 10.1002/app.3514710.1002/app.35147 ↗
38. 10.1155/2013/68510410.1155/2013/685104 ↗