journal article·2022-12

Effects of fabrication method of composite yarn intermediate material and resin melt viscosity on the impregnation properties and mechanical properties of PA66 fiber and glass fiber composites

Taiga Saito, Asami Nakai, Akio Ohtani

Publisher page

Abstract

Continuous fiber-reinforced thermoplastic (c-FRTP) has received attention for reducing automobile weight. Hollow molded parts made by pultrusion molding of braided composites may improve the performance and reduce the weight of automotive parts. However, pultrusion molding of braided composites suffers from productivity problems. This research aimed to increase the productivity of pultrusion molding of braided fabrics to facilitate its practical application. The effects of the fiber intermediate fabrication method and the resin melt viscosity on the impregnation and mechanical properties of the composite were investigated. Glass fiber and polyamide 66 (PA66) were used as the fiber intermediates. Two types of fiber intermediates were used, one with interlace processing and one with the fibers lined up. PA66 fibers with high and low viscosity were used. A correlation was found between impregnation properties and mechanical properties of the molded products, which improved as the unimpregnated ratio decreased. Detailed observations revealed that impregnation of PA66 resin into glass fiber bundles started from interlaced points in the fiber intermediates introduced by interlace processing. Furthermore, low-viscosity PA66 resin had higher fluidity, which better promoted impregnation into glass fiber bundles. These results clarify design guidelines for fiber intermediates to realize better mechanical properties and shorter molding cycles.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Mechanical Behavior of Composites · Natural Fiber Reinforced Composites · Fiber-reinforced polymer composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Asahi Kasei Corporation, Kawasaki, Kanagawa, Japan

Faculty of Fiber Science and Engineering, Kyoto Institute of Technology, Sakyo-ku, Kyoto, Japan

Faculty of Engineering, Gifu University, Gifu City, Gifu, Japan

References (17)

Show source-provided references
1. 10.1016/j.msea.2005.08.06410.1016/j.msea.2005.08.064 ↗
2. 10.6089/jscm.34.5110.6089/jscm.34.51 ↗
3. 10.6089/jscm.34.21110.6089/jscm.34.211 ↗
4. Ishikawa T · Int J Automot Eng · 2014 · 68 · 4
5. Yamane K
6. Bitterlich M · Kunststoffe · 2014 · 3 · 80
7. 10.1007/s10443-012-9258-710.1007/s10443-012-9258-7 ↗
8. Fujita Y · Jpn Eng Technol Intell · 2002 · 50 · 35
9. Ben G. Continuous fibre FRTP molding methods and characteristics. Tokyo: Nikkan Kogyo Shimbun, Ltd, 2015, p. 183.
10. 10.1177/089270571351912110.1177/0892705713519121 ↗
11. 10.1177/089270571452691810.1177/0892705714526918 ↗
12. 10.1177/09636935020110020310.1177/096369350201100203 ↗
13. 10.1016/S0266-3538(98)00011-610.1016/S0266-3538(98)00011-6 ↗
14. Choi BD · 796
15. Patou J · 26
16. 10.1016/S1359-835X(97)00002-X10.1016/S1359-835X(97)00002-X ↗
17. 10.1016/S0266-3538(00)00234-710.1016/S0266-3538(00)00234-7 ↗