Tribological studies on effect of mixture of fillers in polystyrene matrix composites
Source abstract
Abstract
Addition of measured amounts of fillers into a polymer matrix is expected to improve the desired properties of the composites. Also the ease of processability of the matrix and reinforcement is always desired. Use of powder fillers in the polymer matrix at ambient conditions would make the processing much easier. This will help in in situ applications. In the present work, polymer–matrix composites are prepared with polystyrene as the matrix using metal (copper/aluminum/steel) and ceramic (alumina) fillers at ambient conditions. The composites with metallic and ceramic fillers in the ratio of 50:25:25 wt% (polymer:filler 1:filler 2) designated as three-phase composites were investigated for tribological applications. Both copper and aluminum fillers were considered for comparison in terms of their contribution to tribological behavior because of their thermal conductivity, specific heat and density. Polystyrene is filled with metal powder (copper, aluminum or steel) and alumina in equal proportion and subjected to wear and friction tests. The polymer steel–ceramic composite has the least with the other two composites having almost the same values of friction coefficient. The polymer aluminum–ceramic composite has the least wear at all operating conditions. Polymer aluminum–ceramic composite was found to have better wear behavior among the three-phase composites. This may be attributed to the favorable value of density of aluminum, moderate thermal conductivity and excellent specific heat.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Tribology and Wear Analysis · Natural Fiber Reinforced Composites · Polymer Nanocomposites and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Center for Emerging Technologies, Jain University, Jakkasandra Post, Kanakapura Taluk, Bengaluru, India
High Pressure Laboratory, Materials Science Division, National Aerospace Laboratories, CSIR, Bengaluru, India
References (17)
Show source-provided references
1. 10.1016/j.wear.2007.10.00310.1016/j.wear.2007.10.003 ↗
2. 10.1016/j.triboint.2007.08.00310.1016/j.triboint.2007.08.003 ↗
3. 10.1177/089270571142180510.1177/0892705711421805 ↗
4. 10.1016/j.wear.2006.04.01210.1016/j.wear.2006.04.012 ↗
5. Cheng H, Cheng X. Mechanical and tribological properties of MWCNTs-reinforced thermoplastic poly(p-oxybenzoate) composites. J Thermoplast Compos Mater 2012; 31(11): 785–795.
6. 10.1002/app.128610.1002/app.1286 ↗
7. Deleanu L, Ripa M, Birsan IG, . Tribological aspects of a metal + polymer composite. The Annals of the University “Dunarea de Jos” of Galati, fascicle VIII, Tribology 2006; 1221–4590 (XII): 14–21.
8. 10.1016/j.wear.2005.02.05410.1016/j.wear.2005.02.054 ↗
9. 10.1016/S0043-1648(97)00178-610.1016/S0043-1648(97)00178-6 ↗
10. 10.1016/j.wear.2004.10.00810.1016/j.wear.2004.10.008 ↗
11. 10.1016/j.wear.2005.03.00310.1016/j.wear.2005.03.003 ↗
12. 10.1016/S0043-1648(02)00144-810.1016/S0043-1648(02)00144-8 ↗
13. 10.1016/S0043-1648(03)00196-010.1016/S0043-1648(03)00196-0 ↗
14. Basavarajappa S, Arun KV, Paulo Davim J. Effect of filler materials on sliding wear behavior of polymer matrix composites: a Taguchi approach. J Min Mater Charact Eng 2009; 8(5): 379–391.
15. 10.1016/j.triboint.2006.12.00210.1016/j.triboint.2006.12.002 ↗
16. 10.1016/j.wear.2008.08.01310.1016/j.wear.2008.08.013 ↗
17. Basavaraj E, Ramaraj B, Siddaramaiah. Investigations on the influence of polytetrafluoroethylene powder as a filler on physico-mechanical and wear characteristics of nylon 66/graphite composite. High Perform Polym 2012; 24: 1–9.