Investigating the annealing effects on the mechanical, morphological and surface properties of 3D printed PETG/OMMT nanoclay composites
Source abstract
Abstract
Fused Filament Fabrication (FFF) is a highly sought-after manufacturing method that builds parts layer by layer using thermoplastic and/or composite filaments. However, it is characterised by weak interlayer adhesion, resulting in low interlaminar strength in printed structures. Recent research suggests that post-processing heat treatments can address this issue by lowering internal thermal stresses and increasing interlayer bonding, thereby improving part properties. This study investigates the effect of annealing heat treatment on a composite consisting of glycol-modified polyethylene terephthalate (PETG) and organically modified montmorillonite nanoclay (OMMT-NC). The annealing temperature was set at 90°C, and the time duration was varied to 60, 120, and 180 minutes. The mechanical, morphological and surface properties of the OMMT-NC reinforced PETG composite were compared with those of pure PETG. Also, annealing effect on the glass transition temperatures was determined by differential scanning calorimetry (DSC). Atomic Force Microscopy (AFM) was used to investigate the change in surface roughness resulting from annealing. The experimental results show that PETG reinforced with 3 wt.% OMMT nanoclay improved the tensile, compression, flexural, and impact strength by 6.9%, 22.9%, 30.3%, and 87.5%, respectively, after annealing. The hardness also increased across all PETG composites by at least 5%, due to improved interlayer adhesion. Morphological studies were conducted to correlate the deformation behaviour and assess the impact of annealing. The findings of this work indicate that PETG/OMMT-NC composites are a potential candidate for structural applications.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Polymer Nanocomposites and Properties · Epoxy Resin Curing Processes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Indian Institute of Science
KU Leuven
National Institute of Technology Silchar
Composites and Additive Manufacturing Research Analysis (CAMRA) Laboratory, Department of Industrial Engineering and Management, Siddaganga Institute of Technology, Tumakuru, Karnataka, India
Funding
Department of Science and Technology · Science and Engineering Research Board
References (51)
Show source-provided references
1. 10.1016/j.pmatsci.2020.10063810.1016/j.pmatsci.2020.100638 ↗
2. Iso A. ISO/ASTM 52900: 2015 additive manufacturing–general principles–terminology. ASTM, 2015, vol 1, pp. 1–19. F2792-10e1.
3. 10.3390/polym1305070110.3390/polym13050701 ↗
4. 10.1007/s40436-014-0097-710.1007/s40436-014-0097-7 ↗
5. 10.1016/j.prostr.2020.04.05610.1016/j.prostr.2020.04.056 ↗
6. 10.1016/j.compositesb.2017.02.04510.1016/j.compositesb.2017.02.045 ↗
7. 10.1557/jmr.2014.21210.1557/jmr.2014.212 ↗
8. 10.1016/j.compscitech.2014.10.00910.1016/j.compscitech.2014.10.009 ↗
9. 10.1007/s11668-014-9803-910.1007/s11668-014-9803-9 ↗
10. 10.1016/j.compositesb.2018.02.01210.1016/j.compositesb.2018.02.012 ↗
11. 10.1177/0954008321106738810.1177/09540083211067388 ↗
12. 10.1007/s12206-017-0415-710.1007/s12206-017-0415-7 ↗
13. 10.1016/S0924-0136(01)00980-310.1016/S0924-0136(01)00980-3 ↗
14. Nancharaiah T, Ranga Raju D, Ramachandra Raju V. An experimental investigation on surface quality and dimensional accuracy of FDM components. Int J Emerg Technol 2019; 2(2): 106–111, [Online]. Available: https://www.researchgate.net/publication/267248480
15. 10.3390/ma1104050010.3390/ma11040500 ↗
16. 10.1108/1355254021044116610.1108/13552540210441166 ↗
17. 10.1016/j.jmapro.2015.11.00210.1016/j.jmapro.2015.11.002 ↗
18. 10.1007/s11837-015-1367-y10.1007/s11837-015-1367-y ↗
19. 10.1177/1687813222112073710.1177/16878132221120737 ↗
20. 10.1080/14658011.2020.172965710.1080/14658011.2020.1729657 ↗
21. 10.1016/j.compscitech.2018.08.04810.1016/j.compscitech.2018.08.048 ↗
22. 10.1016/j.polymdegradstab.2019.06.00110.1016/j.polymdegradstab.2019.06.001 ↗
23. KevinHart R, EricWetzel D. Fracture behavior of additively manufactured acrylonitrile butadiene styrene (ABS) materials. Eng Frac Mech 2017; 177: 1–13. https://doi.org/10.1016/j.engfracmech.2017.03.028
24. 10.1016/j.mtcomm.2020.10136510.1016/j.mtcomm.2020.101365 ↗
25. 10.1088/1757-899X/1182/1/01208310.1088/1757-899X/1182/1/012083 ↗
26. Diani J, Gall K. Finite strain 3D thermoviscoelastic constitutive model. Society 2006; 51(7): 1–10. https://doi.org/10.1002/pen
27. 10.1016/j.compscitech.2019.10771210.1016/j.compscitech.2019.107712 ↗
28. 10.1016/j.ijbiomac.2014.12.02210.1016/j.ijbiomac.2014.12.022 ↗
29. Hong JH, Yu T, Chen Z, et al. Improvement of flexural strength and compressive strength by heat treatment of PLA filament for 3D-printing. Mod Phys Lett B 2019; 33(14–15): 3–7. https://doi.org/10.1142/S0217984919400256
30. 10.1016/j.matpr.2020.10.07810.1016/j.matpr.2020.10.078 ↗
31. Jannet S, Soundararajan R, Ratna Kandavalli S, et al. Wear and friction behavior on extrusion-based 3D printed short carbon fiber reinforced PETG composites with annealing and laser treated effects. J Inst Eng: Series 2024; 1–10. https://doi.org/10.1007/s40033-024-00794-6
32. 10.1016/j.matpr.2021.02.41710.1016/j.matpr.2021.02.417 ↗
33. 10.4271/2020-28-042910.4271/2020-28-0429 ↗
34. Ranganathan S, Thangaraj HNRS, Kumar Vasudevan A, et al. Analogy of thermal properties of Polyamide 6 reinforced with glass fiber and glass beads through FDM process. SAE Technical Paper. 2020, No. 2019-28-0137: https://doi.org/10.4271/2019-28-0137
35. 10.1177/089270571984724410.1177/0892705719847244 ↗
36. Barkhad MS, Abu-jdayil B, Mourad AHI, et al. Thermal insulation and mechanical properties of. Polymers 2020; 12: 1–16.
37. 10.1108/RPJ-05-2016-007710.1108/RPJ-05-2016-0077 ↗
38. 10.1007/s00170-006-0556-910.1007/s00170-006-0556-9 ↗
39. 10.1016/j.matdes.2013.02.06710.1016/j.matdes.2013.02.067 ↗
40. 10.1016/j.prostr.2022.02.00410.1016/j.prostr.2022.02.004 ↗
41. 10.1016/j.matpr.2022.02.14210.1016/j.matpr.2022.02.142 ↗
42. 10.1016/j.progpolymsci.2003.08.00210.1016/j.progpolymsci.2003.08.002 ↗
43. 10.1016/S0927-796X(00)00012-710.1016/S0927-796X(00)00012-7 ↗
44. 10.1016/j.progpolymsci.2008.07.00810.1016/j.progpolymsci.2008.07.008 ↗
45. 10.1002/pc.2598510.1002/pc.25985 ↗
46. 10.1002/pc.2616310.1002/pc.26163 ↗
47. 10.1177/0892705724123900110.1177/08927057241239001 ↗
48. Struik, Leendert Cornelis Elisa. Physical aging in amorphous polymers and other materials, 1978. Elsevier Scientific Publishing Company, (No Title).
49. 10.1002/pen.1059910.1002/pen.10599 ↗
50. 10.1016/j.progpolymsci.2008.07.00810.1016/j.progpolymsci.2008.07.008 ↗
51. 10.1209/0295-5075/27/1/01110.1209/0295-5075/27/1/011 ↗