Effect of friction stir welding parameters on the mechanical performance of recycled HDPE plates
Source abstract
Abstract
Friction stir welding (FSW) was investigated as a solid-state processing technique for joining recycled high-density polyethylene (HDPE) plates manufactured from post-consumer bottle caps and previously used as construction formworks. The effects of rotational and traverse speeds on weld densification and mechanical performance were systematically evaluated to establish processing–structure–property relationships in recycled thermoplastic systems. Mechanical characterization included ultimate tensile strength (UTS), density, and Shore D hardness, and load–elongation response, while surface and cross-sectional morphological analyses were used to assess void formation, material consolidation, and weld integrity. Optimal conditions were identified at 1600 rpm with 12.5 mm/min and 1000 rpm with 25.0 mm/min, resulting in UTS values up to 4.7% higher than those of the unwelded material. Morphological analysis revealed that excessive heat input at elevated rotational speeds promoted void formation and reduced joint integrity, whereas moderate parameters enhanced material consolidation and produced defect-free welds. A strong correlation among UTS, density, and hardness confirmed their suitability as indicators of weld quality. These findings demonstrate that controlled FSW parameters can significantly improve the structural performance of recycled HDPE, supporting their use in sustainable construction-related and non-critical engineering applications within circular economy strategies.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Materials Engineering and Processing · Mechanical Behavior of Composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Universidad Michoacana de San Nicolás de Hidalgo
References (48)
Show source-provided references
1. 10.1016/j.chemosphere.2023.13808910.1016/j.chemosphere.2023.138089 ↗
2. 10.1016/j.ijfatigue.2018.04.02410.1016/j.ijfatigue.2018.04.024 ↗
3. 10.3390/ma1521763910.3390/ma15217639 ↗
4. 10.3390/polym1421463210.3390/polym14214632 ↗
5. 10.3390/polym1313205610.3390/polym13132056 ↗
6. 10.1007/s11837-023-05839-x10.1007/s11837-023-05839-x ↗
7. 10.1007/s00170-018-2504-x10.1007/s00170-018-2504-x ↗
8. 10.1177/089270571769777910.1177/0892705717697779 ↗
9. 10.1016/j.procir.2024.02.01110.1016/j.procir.2024.02.011 ↗
10. 10.18196/st.v27i1.2218210.18196/st.v27i1.22182 ↗
11. Kumar R, Singh R, Ahuja IPS. Friction stir welding of thermoplastic composites: a review. J Thermoplast Compos Mater 2019; 32(10): 1377–1406. https://doi.org/10.1177/0954406219848465
12. Ahmed H, van Tooren MJL, Justice J, et al. Investigation and development of friction stir welding process for thermoplastics. J Thermoplast Compos Mater 2019; 32(6): 812–833. https://doi.org/10.1177/0892705718785676
13. Sudoł M, Woźniak A, Rymuza K. Recycling of polyethylene: tribology assessment. Resour Conserv Recycl 2023; 191: 106878. https://doi.org/10.1016/j.resconrec.2023.106878
14. 10.1016/j.polymertesting.2012.11.00710.1016/j.polymertesting.2012.11.007 ↗
15. 10.1007/s10965-020-02332-w10.1007/s10965-020-02332-w ↗
16. Frigione M, Lettieri M. Mechanical properties of concrete reinforced with recycled HDPE plastic fibres. Constr Build Mater 2016; 125: 544–555. https://doi.org/10.1016/j.conbuildmat.2016.04.050
17. Burger J, Lloret-Fritschi E, Akermann M, et al. Circular formwork: recycling of 3D printed thermoplastic formwork for concrete. Technol Archit Des 2023; 7(2): 204–215. https://doi.org/10.1080/24751448.2023.2245724
18. Khan MA, Ahmad S, Ali M, et al. Optimization of friction stir welding parameters for enhanced mechanical properties of AISI 1018 carbon steel. Sci Rep 2025; 15: 16668. https://doi.org/10.1038/s41598-025-16668-0
19. 10.1016/S1003-6326(19)65134-410.1016/S1003-6326(19)65134-4 ↗
20. 10.1007/s11665-023-08671-110.1007/s11665-023-08671-1 ↗
21. Teja PJ, Jain R. Effect of external heat assistance on the weld quality of AA2024 aluminium alloy during friction stir welding. Manuf Technol Today 2023; 22(1): 20–24. https://doi.org/10.58368/MTT.22.1.2023.20-24
22. 10.1016/j.ijlmm.2024.06.00310.1016/j.ijlmm.2024.06.003 ↗
23. 10.1007/s13369-024-09057-810.1007/s13369-024-09057-8 ↗
24. ASTM International. Standard Test Method for Tensile Properties of Plastics (ASTM D638-22). ASTM International, 2022. https://doi.org/10.1520/D0638-22
25. 10.1016/j.jmapro.2019.07.01310.1016/j.jmapro.2019.07.013 ↗
26. 10.1007/s00170-021-06602-910.1007/s00170-021-06602-9 ↗
27. 10.1007/s00170-019-04006-410.1007/s00170-019-04006-4 ↗
28. 10.1016/j.jmapro.2017.02.01810.1016/j.jmapro.2017.02.018 ↗
29. 10.1016/j.jmapro.2015.07.00510.1016/j.jmapro.2015.07.005 ↗
30. 10.1016/j.jcomc.2022.10026910.1016/j.jcomc.2022.100269 ↗
31. 10.1016/j.jmapro.2018.03.01010.1016/j.jmapro.2018.03.010 ↗
32. 10.1007/s00170-019-04840-610.1007/s00170-019-04840-6 ↗
33. 10.1007/s40194-020-00890-710.1007/s40194-020-00890-7 ↗
34. Mishra D, Sahu SK, Mahto RP, et al. Friction stir welding for joining of polymers. In: Strengthening and Joining by Plastic Deformation. Springer, 2018, pp. 123–162. https://doi.org/10.1007/978-981-13-0378-4_6
35. 10.1016/j.jmrt.2022.03.08210.1016/j.jmrt.2022.03.082 ↗
36. 10.3390/polym1515323010.3390/polym15153230 ↗
37. Wu MS, Centea T, Nutt SR. Compression molding of reused in-process waste: effects of material and process factors. Adv Manuf Polym Compos Sci 2018; 4(1): 1–12. https://doi.org/10.1080/20550340.2017.1411873
38. 10.1007/s42452-021-04908-710.1007/s42452-021-04908-7 ↗
39. 10.1016/j.jmrt.2023.05.18410.1016/j.jmrt.2023.05.184 ↗
40. 10.1038/s41524-019-0207-y10.1038/s41524-019-0207-y ↗
41. 10.1016/j.matdes.2013.12.03810.1016/j.matdes.2013.12.038 ↗
42. 10.3390/met1210166010.3390/met12101660 ↗
43. 10.1016/j.matdes.2024.11342910.1016/j.matdes.2024.113429 ↗
44. 10.1007/978-981-15-1201-8_9910.1007/978-981-15-1201-8_99 ↗
45. 10.1016/j.heliyon.2023.e1762710.1016/j.heliyon.2023.e17627 ↗
46. 10.1016/j.compositesb.2017.10.03910.1016/j.compositesb.2017.10.039 ↗
47. Singh S, Singh R, Ahuja IPS. Friction stir welding of thermoplastics: an overview. Mater Today Proc 2021; 47(7): 2244–2250. https://doi.org/10.1016/j.matpr.2021.05.528
48. Zhou L, Zhang Z, Li Y. Effect of process parameters on mechanical properties and microstructure of friction stir welded HDPE sheets. J Mater Res Technol 2020; 9(3): 3091–3100. https://doi.org/10.1016/j.jmrt.2020.01.064