Identification and thermomechanical analysis of the annular Fiber–Chip accumulation phenomenon in micro-drilling of PA6 glass/carbon hybrid thermoplastic composites
Source abstract
Abstract
The growing adoption of hybrid thermoplastic composites in lightweight advanced structures has heightened the need to understand their behavior during micromachining operations, yet research in this domain remains scarce. In this work, the microdrilling behavior of a PA6–Glass/PA6–Carbon hybrid composite was investigated, with an emphasis on the thermomechanical response and hole-boundary integrity. The results indicate that spindle speed is the primary parameter controlling temperature elevation; however, under all tested conditions, the measured temperatures remained below the matrix melting and degradation thresholds. Microscopic examination of the drilled holes revealed that edge quality and the prevalence of partially sheared fibers were highly influenced by the combined interaction of spindle speed and feed rate. Image analysis revealed a distinct and previously unreported phenomenon, termed Annular Fiber–Chip Accumulation (AFCA), which appeared only under specific parameter combinations and whose morphology was likely driven by restricted chip evacuation in the confined micro-drilling zone. Moreover, the developed temperature model showed a strong agreement with the experimental data, as indicated by the high coefficient of determination and adjusted coefficient of determination values (R 2 = 99.29% and R 2 adj = 98.42%). These results suggest that the model can adequately describe the variation of drilling-zone temperature within the investigated range of machining parameters. By identifying and characterizing a new microstructural pattern along the inner hole boundary, and clarifying its relationship with processing parameters, this study provides new insights to support the optimization of micro-drilling operations in hybrid thermoplastic composites.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced machining processes and optimization · Drilling and Well Engineering · Composite Material Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Arak University of Technology
Tarbiat Modares University
References (41)
Show source-provided references
1. 10.1016/j.promfg.2021.07.04510.1016/j.promfg.2021.07.045 ↗
2. 10.1016/j.procir.2016.02.25510.1016/j.procir.2016.02.255 ↗
3. 10.1016/j.jmatprotec.2014.09.00410.1016/j.jmatprotec.2014.09.004 ↗
4. 10.1016/j.compositesa.2019.10555210.1016/j.compositesa.2019.105552 ↗
5. 10.1016/j.compstruct.2014.06.03410.1016/j.compstruct.2014.06.034 ↗
6. 10.1177/002199831988333510.1177/0021998319883335 ↗
7. 10.1016/j.wear.2021.20373810.1016/j.wear.2021.203738 ↗
8. 10.1016/j.dt.2018.02.00110.1016/j.dt.2018.02.001 ↗
9. 10.1016/j.jmatprotec.2014.07.01610.1016/j.jmatprotec.2014.07.016 ↗
10. 10.1016/j.matpr.2017.12.17110.1016/j.matpr.2017.12.171 ↗
11. 10.1016/j.jmapro.2018.01.01110.1016/j.jmapro.2018.01.011 ↗
12. 10.1007/s00170-017-1009-310.1007/s00170-017-1009-3 ↗
13. 10.1177/095440621987791110.1177/0954406219877911 ↗
14. 10.1088/1361-6439/ac11cb10.1088/1361-6439/ac11cb ↗
15. 10.1177/073168440708425910.1177/0731684407084259 ↗
16. 10.1016/j.compstruct.2019.11170810.1016/j.compstruct.2019.111708 ↗
17. 10.1007/s12289-021-01644-610.1007/s12289-021-01644-6 ↗
18. 10.1177/0021998324127100410.1177/00219983241271004 ↗
19. 10.1007/s40436-015-0129-y10.1007/s40436-015-0129-y ↗
20. Beyranvand R, Ansari M, Deilami AH, et al. Effect of drilling parameters on fiber delamination, surface quality, and drilling force in curved luminum/glass/polypropylene composite. Iran J Manuf Eng 2025; 12(7): 81–95.
21. 10.1016/j.rineng.2024.10373810.1016/j.rineng.2024.103738 ↗
22. Slamani M, Chatelain J-F (eds). Issues and challenges in robotic trimming of CFRP. 2015 12th international conference on informatics in control, automation and robotics (ICINCO). IEEE, 2015.
23. 10.1007/s00170-026-18181-810.1007/s00170-026-18181-8 ↗
24. 10.1016/j.jmapro.2017.08.00610.1016/j.jmapro.2017.08.006 ↗
25. 10.3390/mi1406116010.3390/mi14061160 ↗
26. 10.1016/j.physa.2021.12584210.1016/j.physa.2021.125842 ↗
27. 10.3390/jmmp1006018410.3390/jmmp10060184 ↗
28. Sağener M Çolak O. Enhanced MQL cooling technique for hole quality in carbon fiber reinforced composites: A study on the influence of nanographene in drilling process. Results in Engineering 2024; 2026;30:110005. https://doi.org/10.1016/j.rineng.2026.11000510.1016/j.rineng.2026.110005 ↗
29. 10.1016/j.rineng.2024.10312810.1016/j.rineng.2024.103128 ↗
30. 10.1016/j.rineng.2025.10410210.1016/j.rineng.2025.104102 ↗
31. 10.1007/s00170-024-14855-310.1007/s00170-024-14855-3 ↗
32. 10.1177/0892705725138283110.1177/08927057251382831 ↗
33. 10.1016/j.compositesb.2014.12.03410.1016/j.compositesb.2014.12.034 ↗
34. Petrucci R Nisini E Ghelli D et al. (eds). Mechanical and impact characterisation of hybrid composite laminates based on flax hemp basalt and glass fibers produced by vacuum infusion. In: ECCM15 15th European conference on composite materials Venice Italy 24–28 June 2012.
35. 10.1016/j.rineng.2025.10574110.1016/j.rineng.2025.105741 ↗
36. 10.1177/0954411921103435310.1177/09544119211034353 ↗
37. 10.1177/0021998322109284310.1177/00219983221092843 ↗
38. Fereyduni F, Ansari M, Baraheni M. The role of drilling parameters in controlling delamination and hole quality of novel long-fiber PLA-glass composites manufactured by FDM. Iran J Manuf Eng 2025; 12(1): 51–64.
39. 10.1177/0021998324127103510.1177/00219983241271035 ↗
40. 10.1016/j.compositesa.2009.08.00210.1016/j.compositesa.2009.08.002 ↗
41. Toray Performance Materials Corporation. Toray CFRT® material selector guide: Toray Performance Materials Corporation. 1986; ver.: 5.0.