Plasma enhanced atomic layer deposition of textured aluminum nitride on platinized substrates for MEMS
Source abstract
Abstract
We demonstrate an N2 plasma-enhanced process for inducing (0001)-oriented ALD-grown AlN on planar substrates. We evaluate the impact of {111}-textured Pt as a growth template, precursor chemistry, dose time, stress-engineered substrates, inductively coupled plasma conditions for film bombardment during growth, and ALD equipment configurations. The thin film transverse piezoelectric coefficient e31,f determined from measurements on microelectromechanical system cantilevers coated by PEALD AlN is reported to be −0.53 ± 0.03 C/m2. An analysis of the Pt-AlN interface properties based primarily on depth-profile x-ray photoemission spectroscopy and transmission electron microscopy-energy dispersive spectra is presented. Other than the c axis wurtzite (0001) diffraction peak, no other AlN peaks were observed above the detection limits for XRD measurements. The XRD rocking-curve full-width half-maximum of the 0001 peaks was 2.9° omega, which was achieved on {111}-textured Pt. The relative dielectric constant was measured to be 8.1 < K < 8.6, and an average dielectric loss of < 0.01 was observed within the applied electric field range of ±3350 kV/cm at 10 kHz. The leakage current of the textured AlN was quite low at 1.5 × 10−6 A/cm2 over the applied field range of ±1820 kV/cm.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: GaN-based semiconductor devices and materials · Acoustic Wave Resonator Technologies · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Sensors and Electron Devices Directorate, CCDC Army Research Laboratory 1 , 2800 Powder Mill Road, Adelphi, Maryland 20783
Kurt J. Lesker Company 2 , 1925 PA-51, Jefferson Hills, Pennsylvania 15025
Fox Materials Consulting, LLC 3 , Colorado Springs, Colorado 80908-6321
Materials Research Institute, The Pennsylvania State University 4 , University Park, Pennsylvania 16802
References (29)
Show source-provided references
1. J. S. Pulskamp and R. G. Polcawich, U.S. patent US,896,699,3B2 (2012).
2. J. Vac. Sci. Technol. A · 2009 · 27 · 77610.1116/1.3077276 ↗
3. IEEE Trans. Ultrason. Ferroelectr. Freq. Control · 2007 · 54 · 242210.1109/TUFFC.2007.555 ↗
4. Sens. Actuators, A · 2012 · 188 · 30510.1016/j.sna.2011.12.029 ↗
5. J. Micromech. Microeng. · 1996 · 6 · 32010.1088/0960-1317/6/3/004 ↗
6. Sens. Actuators A · 2006 · 132 · 31110.1016/j.sna.2006.06.006 ↗
7. J. Microelectromech. Syst. · 2006 · 15 · 140610.1109/JMEMS.2006.886012 ↗
8. MRS Bull. · 2012 · 37 · 105110.1557/mrs.2012.268 ↗
9. Sens. Actuators A · 1999 · 77 · 10610.1016/S0924-4247(99)00070-9 ↗
10. Chem. Mater. · 2002 · 5 · 142410.1021/cm00034a010 ↗
11. J. Appl. Phys. · 1994 · 75 · 538510.1063/1.355693 ↗
12. Chem. Mater. · 1996 · 8 · 235910.1021/cm9601906 ↗
13. Chem. Mater. · 2002 · 14 · 72010.1021/cm011176i ↗
14. Thin Solid Films · 1996 · 289 · 15910.1016/S0040-6090(96)08927-4 ↗
15. Thin Solid Films · 2004 · 446 · 22710.1016/j.tsf.2003.10.004 ↗
16. 2004 · 11
17. J. Appl. Phys. · 2008 · 104 · 09371310.1063/1.2966482 ↗
18. Appl. Phys. Lett. · 2013 · 103 · 08211010.1063/1.4818792 ↗
19. Tech. Phys. Lett. · 2017 · 43 · 7410.1134/S1063785017010138 ↗
20. APL Mater. · 2020 · 8 · 07110110.1063/5.0011331 ↗
21. J. Vac. Sci. Technol. A · 2021 · 39 · 03240310.1116/6.0000724 ↗
22. J. Mater. Sci. Mater. Electron. · 2018 · 29 · 41210.1007/s10854-017-7930-2 ↗
23. J. Vac. Sci. Technol. A · 2020 · 38 · 06240810.1116/6.0000454 ↗
24. ACS Appl. Mater. Interfaces · 2020 · 12 · 3987010.1021/acsami.0c10515 ↗
25. J. Vac. Sci. Technol. A · 2019 · 37 · 02091310.1116/1.5079628 ↗
26. J. Vac. Sci. Technol. A · 2020 · 38 · 02240510.1116/1.5128663 ↗
27. Appl. Surf. Sci. · 2014 · 315 · 10410.1016/j.apsusc.2014.07.105 ↗
28. J. Appl. Phys. · 2013 · 113 · 08430610.1063/1.4792942 ↗
29. See the supplementary material at https://www.scitation.org/doi/suppl/10.1116/6.0001633 for for an example of the curve fitting, table containing the mechanical properties used for strain modeling, nested polarization–voltage figure, and schematic cross section of the fabricated cantilevers.