Estimation of mass and moisture content of flat square lumber in a stack during air-drying process by the vibration method with additional mass
Source abstract
Abstract
Abstract A vibration test to measure the mass of a specimen without weighing it using the difference between the resonance frequency with an additional mass and that without it (vibration method with additional mass, VAM) was applied to Japanese cedar flat square lumber with dimensions of 210 mm × 135 mm × 3000 mm both with and without a pith in the process of air-drying. The longitudinal and bending vibration tests were performed on the specimens with and without an additional mass. The accuracy of VAM that was expressed by the estimated mass by VAM to the measured mass (MVAM/M0) was sufficiently high throughout the air-drying process. The accuracy of VAM for the longitudinal vibration was higher than that for the bending vibration. The moisture content based on the estimated mass by VAM was in the expected range.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Textile materials and evaluations · Wood Treatment and Properties · Mechanical and Thermal Properties Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (17)
Show source-provided references
1. Matsumura Y (2017) Wood properties and issues of sawmilling for large-diameter Sugi Logs. Abstracts of Mokuzai to Mizu Kenkyukai. 1–7
2. Nakayama Y (1968) Studies on the dynamic Young’s modulus of wooden beam (I) The dynamic Young’s modulus and the bending strength. Bull Kochi Univ For 2:17–32
3. Skrinar M (2002) On elastic beams parameter identification using eigen frequencies changes and the method of added mass. Comput Mater Sci 25:207–21710.1016/S0927-0256(02)00265-3 ↗
4. Türker T, Bayraktar A (2008) Structural parameter identification of fixed end beams by inverse method using measured natural frequencies. Shock Vib 15:505–51510.1155/2008/692962 ↗
5. Kubojima Y, Sonoda S (2015) Measuring Young’s modulus of a wooden bar using longitudinal vibration without measuring its weight. Eur J Wood Wood Prod 73:399–40110.1007/s00107-015-0884-2 ↗
6. Matsubara M, Aono A, Kawamura S (2015) Experimental identification of structural properties of elastic beam with homogeneous and uniform cross section. Trans JSME. https://doi.org/10.1299/transjsme.15-0027910.1299/transjsme.15-00279 ↗
7. Kubojima Y, Kato H, Tonosaki M, Sonoda S (2016) Measuring Young’s modulus of a wooden bar using flexural vibration without measuring its weight. BioResources 11:800–810
8. Matsubara M, Aono A, Ise T, Kawamura S (2016) Study on identification method of line density of the elastic beam under unknown boundary conditions. Trans JSME. https://doi.org/10.1299/transjsme.15-0066910.1299/transjsme.15-00669 ↗
9. Kubojima Y, Sonoda S, Kato H (2018) Application of the vibration method with additional mass to timber guardrail beams. J Wood Sci 64:767–77510.1007/s10086-018-1771-3 ↗
10. Kubojima Y, Sonoda S, Kato H (2020) Mass of piled lumber estimated through vibration test. J Wood Sci 66:3210.1186/s10086-020-01880-5 ↗
11. Kubojima Y, Sonoda S, Kato H (2021) Mass of piled round bar estimated through vibration tests. Wood Fib Sci 53:216–22710.22382/wfs-2021-21 ↗
12. Kubojima Y, Sonoda S, Kato H (2017) Practical techniques for the vibration method with additional mass: effect of crossers’ position in longitudinal vibration. J Wood Sci 63:147–15310.1007/s10086-017-1610-y ↗
13. Kubojima Y, Sonoda S, Kato H (2018) Practical techniques for the vibration method with additional mass: bending vibration generated by tapping cross section. J Wood Sci 64:16–2210.1007/s10086-017-1676-6 ↗
14. Kubojima Y, Suzuki Y, Kato H, Kobayashi I, Matsumoto H, Ishida Y (2021) Temporal change in moisture gradient in flat square lumber produced from large-diameter log during natural drying. Wood Ind 76:540–544
15. Kubojima Y, Sonoda S, Kato H (2017) Practical techniques for the vibration method with additional mass: effect of specimen moisture content. J Wood Sci 63:568–57410.1007/s10086-017-1653-0 ↗
16. Kubojima Y, Sonoda S, Kato H (2021) Measuring density and Young’s modulus of a log through the vibration test without measuring its weight. J Wood Sci 67:610.1186/s10086-020-01929-5 ↗
17. Sonoda S, Kubojima Y, Kato H (2017) Application of the vibration method with additional mass to lumber in structural sizes—application to lumber for column use. Abstracts of the 67th Annual Meeting of Japan Wood Research Society, D17-07-1515.