journal article·2025

Investigation of Phase Formation, As-cast Microstructure, Microhardness and 3D Porosity in Quaternary Al – 5 wt.% Si – 4 wt.% Cu – 1 wt.% Ni Alloy Obtained Under Transient Heat-Flow Conditions

Matheus Carvalho Nascimento, Wysllan Jefferson Lima Garção, Paulo Felipe Júnior, Roberto Carlos Sales, Arthur Dias da Silva, Alexandre Furtado Ferreira

Materials Research· Volume 28
Publisher page

Abstract

The present experimental investigation focuses on the phase formation, microstructural patterns, microhardness and 3D porosity for a quaternary Al – 5 wt.% Si – 4 wt.% Cu – 1 wt.% Ni alloy. Through the phase diagram and Thermo-Calc Scheil simulation, one can determine the growth sequence of the phases during the cooling process. With slow cooling curve and its first and second derivatives, one can find both liquidus and solidus temperatures. An approach based on the second derivative curve was adopted to determine the onset of solidification and subsequent phase transformations. These experimental results obtained with slow cooling curves are corroborated by those determined by Thermo-Calc software. An ingot of the quaternary aluminum alloy was produced by upward vertical unidirectional solidification under transient heat extraction conditions. Here, we used a water-cooled system to investigate the thermal parameters effects on the as-cast microstructure, microhardness and 3D porosity. The impacts of solidification thermal conditions on the microstructural patterns, microhardness and porosity formation were presented and discussed. Higher values of solidification thermal parameters and refined as-cast microstructures were key factors acting during solidification, which served to conditions changes in the Vickers microhardness and porosity formation along the casting. The relationship between porosity and cooling rate is presented and discussed from experimental equation, PC = -0.41Ṫ2+2.36Ṫ+2.51. This result indicates that porosity formation is closely connected to the said thermal parameter. With 3D image analysis, the distribution of porosity size in casting can be investigated. For positions close to the water-cooled system, porosity with smaller sizes, were predominant in casting. However, for positions away from the water-cooled system with lower cooling rates, porosity with higher sizes were observed.
Source: crossref · Quality: baseline

Research context

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Universidade Federal Fluminense, Brasil

Instituto Federal do Rio de Janeiro, Brasil

Universidade do Estado do Rio de Janeiro, Brasil

Funding

CNPq

References (20)

Show source-provided references
1. Effects of solidification rate in the microstructure of Al-Si5Cu3 aluminum cast alloy10.1590/1980-5373-mr-2017-0083 ↗
2. Solidification behaviour of Al–Si based alloys with controlled additions of Eu and P10.1080/13640461.2018.1480891 ↗
3. Thermal analysis during solidification of cast Al-Si alloys10.1016/j.tca.2010.06.026 ↗
4. Effect of cooling rate and silicon refiner/modifier on solidification pathways of Al-11.3Si-2Cu-0.4Fe alloy
5. Computer-aided cooling curve thermal analysis of near eutectic Al–Si–Cu–Fe alloy10.1007/s10973-013-3005-7 ↗
6. Transient unidirectional solidification, microstructure and intermetallics in Sn-Ni alloys
7. Phase stability and unidirectional solidification in a Ni-Al bronze10.1016/j.jmrt.2023.06.030 ↗
8. Improved solidification structures and mechanical properties of Al–20 wt% Sn alloys processed by an electromagnetic vibration technique10.1016/j.msea.2022.144416 ↗
9. Investigation of thermal parameters effects on the microstructure, microhardness and microsegregation of Cu-Sn alloy directionally solidified under transient heat flow conditions10.1590/1980-5373-mr-2019-0259 ↗
10. 2025
11. Influence of cerium on microstructure and solidification of eutectic Al-Si piston alloy10.1080/10426914.2015.1127942 ↗
12. Influence of lanthanum on solidification, microstructure, and mechanical properties of eutectic Al-Si piston alloy10.1007/s11665-016-2139-8 ↗
13. Effect of praseodymium and erbium additions on solidification characteristics, microstructure and mechanical properties of as–cast ZRE1 magnesium alloy10.1002/mawe.201600766 ↗
14. Investigations on metallurgical parameters in hypoeutectic Al–Si alloys under upward directional solidifications10.1007/s00170-022-09836-3 ↗
15. The Effect of the growth rate on microsegregation: experimental investigation in hypoeutectic Al–Fe and Al–Cu alloys directionally solidified10.1016/j.jallcom.2013.01.180 ↗
16. Microstructural patterns, microsegregation, porosity, and mechanical properties of hypoeutectic Al-Fe alloy, and its dependency with solidification thermal parameters10.1590/1980-5373-mr-2022-0187 ↗
17. The formation mechanism of porosity for spray-deposited 7075 alloy10.1590/1516-1439.328414 ↗
18. A study of the mechanical properties of an Al–Si–Cu alloy (ADC12) produced by various casting processes10.1016/j.msea.2012.02.073 ↗
19. Combined deformation and solidification-driven porosity formation in aluminum alloys10.1007/s11661-019-05378-8 ↗
20. Reducing shrinkage porosity in high-performance steel castings: case of an ASME B16.34 gate valve body: part 2—simulation and experimental verification