Effect of basalt and kenaf fiber hybridization on the physical, mechanical, and thermal properties of polymer composites
Source abstract
Abstract
Abstract Fiber-reinforced polymer composites are important for sustainable structural materials, but balancing mechanical strength and thermal stability remains challenging, especially with natural and hybrid fibers. This study addresses the gap by examining basalt (B) and kenaf (K) fiber hybrid composites with different stacking sequences. The objective was to assess how fiber arrangement affects physical, mechanical properties, thermal stability, and microstructure in polyester composites. Six configurations (B/B/B, B/K/B, B/K/K, K/B/K, K/K/B, and K/K/K) were fabricated using hand lay-up and compression molding. Results show that B/B/B has the highest tensile strength (85 MPa), lowest void content (2.6 %), and minimal water absorption, indicating strong fiber–matrix bonding. The K/K/K composite exhibited the lowest tensile strength (42 MPa), highest void content (5.5 %), and greatest water uptake, reflecting poor bonding. Thermal analysis revealed degradation between 120 and 220 °C, with basalt-rich composites having lower thermal stability than kenaf-rich ones. SEM images confirmed strong adhesion in basalt-rich composites and fiber pull-out with matrix cracks in kenaf-rich laminates. These findings highlight that basalt fibers enhance mechanical properties while kenaf fibers improve thermal resistance, guiding the design of hybrid composites for applications requiring a balance of strength and thermal stability.
Source: crossref · Quality: baseline
Research context
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Mechanical Engineering , 154105 Velammal College of Engineering and Technology , Madurai , India
Mechanical Engineering , Sri Krishna College of Engineering and Technology , Coimbatore , India
Department of Mechanical Engineering , St. Joseph’s College of Engineering , Chennai , India
References (27)
Show source-provided references
1. K. Rasu and A. Veerabathiran, “Performance of high strength natural fiber reinforced hybrid composites for structural engineering applications,” Mater. Test., vol. 67, no. 3, pp. 553–560, 2025, https://doi.org/10.1515/mt-2024-0381.10.1515/mt-2024-0381 ↗
2. S. Balasubramaniam, R. Ramalingam, and K. Rasu, “Friction and wear behavior of alkali-treated corn husk fiber reinforced polyester composites,” Mater. Test., vol. 67, no. 3, pp. 543–552, 2025, https://doi.org/10.1515/mt-2024-0366.10.1515/mt-2024-0366 ↗
3. A. Veerabathiran, R. Palanichamy, and K. Rasu, “Effect of chitosan on mechanical and thermal properties of novel Aloe vera fiber reinforced composites,” Mater. Test., vol. 66, no. 6, pp. 867–875, 2024, https://doi.org/10.1515/mt-2023-0283.10.1515/mt-2023-0283 ↗
4. K. Rasu and A. Veerabathiran, “Influence of betel nut fiber hybridization on properties of novel aloevera fiber-reinforced vinyl ester composites,” Mater. Test., vol. 66, no. 9, pp. 1475–1482, 2024, https://doi.org/10.1515/mt-2024-0108.10.1515/mt-2024-0108 ↗
5. Ö. Keleş, S. Bati, and Y. H. Çelik, “Hybrid effect on tensile, flexural, and quasi-static punch shear behavior of jute/ramie and jute/flax reinforced hybrid composites,” Mater. Test., vol. 66, no. 6, pp. 802–816, 2024, https://doi.org/10.1515/mt-2023-0383.10.1515/mt-2023-0383 ↗
6. K. Rasu and A. Veerabathiran, “Tribological behaviour of industrial waste based agave sisalana/glass fiber reinforced hybrid composites for marine applications,” Mater. Test., vol. 65, no. 4, pp. 593–602, 2023, https://doi.org/10.1515/mt-2022-0431.10.1515/mt-2022-0431 ↗
7. K. Rasu and A. Veerabathiran, “Characterization of bauxite residue filled sisal/glass fiber reinforced hybrid composites for structural applications,” Mater. Test., vol. 66, no. 11, pp. 1911–1919, 2024, https://doi.org/10.1515/mt-2024-0162.10.1515/mt-2024-0162 ↗
8. A. Doğan and Ç. Güneş, “Mechanical and thermal properties of short banana fiber reinforced polyoxymethylene composite materials dependent on alkali treatment,” Mater. Test., vol. 66, no. 4, pp. 625–635, 2024, https://doi.org/10.1515/mt-2023-0308.10.1515/mt-2023-0308 ↗
9. S. Ekşi, F. E. Danyildiz, N. Özsoy, and M. Özsoy, “Tensile, bending, and impact properties of laminated carbon/aramid/glass hybrid fiber composites,” Mater. Test., vol. 65, no. 12, pp. 1826–1835, 2023, https://doi.org/10.1515/mt-2023-0207.10.1515/mt-2023-0207 ↗
10. H. S. Hedia, M. A. Almas, H. M. Attar, F. A. Thobiani, M. A. Soliman, and M. H. Hedia, “Mechanical behavior of carbon nanotubes reinforced polymer,” Mater. Test., vol. 66, no. 6, pp. 921–929, 2024, https://doi.org/10.1515/mt-2023-0187.10.1515/mt-2023-0187 ↗
11. B. Çevik and Y. Avşar, “Production and characterization of waste walnut shell powder that can be used as a sustainable eco-friendly reinforcement in biocomposites,” Mater. Test., vol. 66, no. 8, pp. 1314–1326, 2024, https://doi.org/10.1515/mt-2024-0018.10.1515/mt-2024-0018 ↗
12. P. Murugadoss, A. Verma, S. Ballal, “Kenaf/Basalt fiber-reinforced epoxy matrix hybrid composites: current trends, challenges, and future prospects in advanced material development,” Results Eng., vol. 26, p. 104816, 2025. https://doi.org/10.1016/j.rineng.2025.104816.10.1016/j.rineng.2025.104816 ↗
13. T. Raja, D. B. Munuswamy, R. R. Francis, G. Vaidya, S. Sundararaman, and Y. Devarajan, “Experimental investigations on the effect of palm oil in kenaf fibre–reinforced basalt particulate hybrid biocomposite,” Biomass. Conv. Biorefin., vol. 14, no. 4, pp. 5345–5355, 2024, https://doi.org/10.1007/s13399-022-02714-8.10.1007/s13399-022-02714-8 ↗
14. M. R. Mudhuganti, J. L. Prasad, and E. Sammiah, “Impact of Al2O3 on mechanical properties of basalt/kenaf composite,” Mater. Today: Proc., 2023. https://doi.org/10.1016/j.matpr.2023.06.241.10.1016/j.matpr.2023.06.241 ↗
15. J. Mirzaei, A. Fereidoon, and A. G G, “An investigation into the tensile and impact strength of hybrid nanocomposites reinforced with graphene, kenaf fiber, and basalt fiber,” J. Nat. Fibers, vol. 19, no. 16, pp. 12896–12910, 2022, https://doi.org/10.1080/15440478.2022.2079580.10.1080/15440478.2022.2079580 ↗
16. M. Umashankaran, S. Gopalakrishnan, and S. S, “Preparation and characterization of tensile and bending properties of basalt-kenaf reinforced hybrid polymer composites,” Int. J. Polym. Anal. Charact., vol. 25, no. 4, pp. 227–237, 2020, https://doi.org/10.1080/1023666X.2020.1781480.10.1080/1023666X.2020.1781480 ↗
17. I. Mokhtar, M. Y. Yahya, M. R. A. Kadir, and M. F. K, “Effect on mechanical performance of UHMWPE/HDPE-Blend reinforced with Kenaf, Basalt and hybrid Kenaf/Basalt fiber,” Polym. Plast. Technol. Eng., vol. 52, no. 11, pp. 1140–1146, 2013, https://doi.org/10.1080/03602559.2013.798814.10.1080/03602559.2013.798814 ↗
18. V. Fiore, T. Scalici, G. D. Bella, and A. Valenza, “A review on basalt fibre and its composites,” Composites, Part B, vol. 74, pp. 74–94, 2015. https://doi.org/10.1016/j.compositesb.2014.12.034.10.1016/j.compositesb.2014.12.034 ↗
19. Y. Guo, M. Zhou, G. Z. Yin, E. Kalali, N. Wang, and D.-Y. Wang, “Basalt fiber-based flame retardant epoxy composites: preparation, thermal properties, and flame retardancy,” Materials, vol. 14, no. 4, p. 902, 2021, https://doi.org/10.3390/ma14040902.10.3390/ma14040902 ↗
20. M. Mohammed, A. J. M. Jawad, A. M. Mohammed, “Challenges and advancement in water absorption of natural fiber-reinforced polymer composites,” Polym. Test., vol. 124, p. 108083, 2023, https://doi.org/10.1016/j.polymertesting.2023.108083.10.1016/j.polymertesting.2023.108083 ↗
21. B. Hassanpour and V. M. Karbhari, “Characteristics and models of moisture uptake in fiber-reinforced composites: a topical review,” Polymers, vol. 16, no. 16, p. 2265, 2024, https://doi.org/10.3390/polym16162265.10.3390/polym16162265 ↗
22. K. R. P K R and S. Bheemappa, “Experimental investigations on the mechanical behavior of basalt fabric reinforced epoxy composites,” J. Polym. Res., vol. 32, no. 3, p. 83, 2025, https://doi.org/10.1007/s10965-025-04308-0.10.1007/s10965-025-04308-0 ↗
23. R. Raghavendra Rao, S. Pradeep, S. Karthik, K. R. Gopi, and B. S. Shivashankara, “Experimental investigation of effect of hybridization of UHMWPE fibers on the mechanical and physical properties of Basalt fiber reinforced polymer matrix composites,” IOP Conf. Ser.: Mater. Sci. Eng., vol. 1189, no. 1, p. 012025, 2021, https://doi.org/10.1088/1757-899X/1189/1/012025.10.1088/1757-899X/1189/1/012025 ↗
24. D. K. Rajak, D. D. Pagar, P. L. Menezes, and E. Linul, “Fiber-reinforced polymer composites: manufacturing, properties, and applications,” Polymers, vol. 11, no. 10, 2019, https://doi.org/10.3390/polym11101667.10.3390/polym11101667 ↗
25. T. Raja and Y. Devarajan, “Study on the mechanical and thermal properties of basalt fiber-reinforced lead oxide nanoparticle polymer composite for advanced energy storage applications,” J. Energy Storage, vol. 108, p. 115079, 2025. https://doi.org/10.1016/j.est.2024.115079.10.1016/j.est.2024.115079 ↗
26. S. Singh, K. G. Pankaj, and K. R. Ram, “Experimental investigations of mechanical and water absorption behavior of basalt/jute bio composite,” Eng. Res. Express., vol. 7, no. 1, p. 015531, 2025, https://doi.org/10.1088/2631-8695/adaca5.10.1088/2631-8695/adaca5 ↗
27. T. T. da Silva, P. Silveira, M. Ribeiro, “Thermal and chemical characterization of Kenaf fiber (Hibiscus cannabinus) reinforced epoxy matrix composites,” Polymers, vol. 13, no. 12, 2021, https://doi.org/10.3390/polym13122016.10.3390/polym13122016 ↗