journal article·2026-03-26

Qualitative assessment on fold cracking of coated substrates: a digital image-based approach

Magdolna Pál, Tomislav Cigula, Ivana Jurič, Bojan Banjanin, Nada Miketić, Gordana Bošnjaković, Gala Golubović

Publisher page

Abstract

Abstract This study introduces two novel image-based metrics to evaluate fold cracking in coated papers: the Crack Perimeter and Area ratio (CPA ratio) and Fold Crack Distribution (FCD). These metrics aim to supplement traditional white pixel percentage (WPP) measurements by describing crack patterns and their distribution. The results show that both metrics effectively characterise the qualitative aspects of fold cracking. The CPA ratio distinguishes between fine, segmented cracks in lighter papers and larger, cohesive damage in heavier ones. The FCD metric reveals irregular crack distributions in lower basis weight samples and more uniform patterns in heavier papers. Folding in the cross-direction consistently caused more severe and evenly spread damage compared to machine-direction folding. Strong negative correlations were observed between both metrics and the WPP values (R 2 up to 0.9952), confirming their effectiveness in characterising surface damage patterns. Results revealed that flat sample positioning (180°) fails to accurately represent physical damage, while scanning offered superior results compared to photography and microscopy for automated image analysis of fold cracking. These findings highlight the importance of standardised digitisation protocols and methodological transparency in fold crack analysis, while providing new tools for a more comprehensive characterisation of surface damage in coated papers.
Source: crossref · Quality: baseline

Affiliations

Department of Graphic Engineering and Design, Faculty of Technical Sciences , University of Novi Sad , Trg Dositeja Obradovića 6, 21000 , Novi Sad , Serbia

Faculty of Graphic Arts , University of Zagreb , Getaldićeva 2, 10000 , Zagreb , Croatia

Funding

Ministry of Science, Technological Development and Innovation of the Republic of Serbia

References (62)

Show source-provided references
1. Barbier, C., Larsson, P.L., and Östlund, S. (2002). Experimental investigation of damage at folding of coated papers. Nord. Pulp Pap. Res. J. 17: 34–38, https://doi.org/10.3183/npprj-2002-17-01-p034-038.10.3183/npprj-2002-17-01-p034-038 ↗
2. Barbier, C., Rättö, P., and Hornatowska, J. (2012). Coating models for an analysis of cracking behaviour between folded paper and creased board. In: Proceedings of 12th tappi advanced coating fundamentals symposium, Atlanta, Georgia, USA, pp. 5–16.
3. Bota, J., Pibernik, J., Kovačević, D., and Brozović, M. (2022). The effects of flatbed creasing tool on printed paperboard. In: Proceedings the eleventh international symposium GRID 2022, Novi Sad, Serbia, pp. 657–663.10.24867/GRID-2022-p71 ↗
4. Breskvar, K., Ahtik, J., and Možina, K. (2012). Cracking phenomena of coatings on label papers. Cellul. Chem. Technol. 55: 289–297, https://doi.org/10.35812/CelluloseChemTechnol.2021.55.29.10.35812/CelluloseChemTechnol.2021.55.29 ↗
5. Chen, S. and Wells, L.J. (2022). A multi-image monitoring framework for statistical process control to improve manufacturing systems. Qual. Reliab. Eng. Int. 38: 679–702, https://doi.org/10.1002/qre.3008.10.1002/qre.3008 ↗
6. dos Santos, J.W.S., Garcia, V.A.d.S., Venturini, A.C., Carvalho, R.A.d., da Silva, C.F., and Yoshida, C.M.P. (2022). Sustainable coating paperboard packaging material based on chitosan, palmitic acid, and activated carbon: water vapor and fat barrier performance. Foods 11: 4037, https://doi.org/10.3390/foods11244037.10.3390/foods11244037 ↗
7. Eklund, J., Österberg, B., Eriksson, L., and Eindenvall, L. (2002). Finishing of digital prints – a failure mapping. In: Proceedings of the 18th international congress on digital printing technologies, San Diego, California, USA, pp. 712–715, https://library.imaging.org/admin/apis/public/api/ist/website/downloadArticle/print4fab/18/1/art00069_2 (Accessed 15 April 2025).10.2352/ISSN.2169-4451.2002.18.1.art00069_2 ↗
8. Fadel, M.S., Abou-Elseoud, W.A., Hassan, E.A., Ibrahim, S., and Hassan, M.L. (2022). Use of sugar beet cellulose nanofibers for paper coating. Ind. Crops Prod. 180: 114787, https://doi.org/10.1016/j.indcrop.2022.114787.10.1016/j.indcrop.2022.114787 ↗
9. Feng, H., Zhou, W., Deng, J., Tian, Q., and Li, H. (2025). DocScanner: robust document image rectification with progressive learning. Int. J. Comput. Vis. 133: 5343–5362, https://doi.org/10.1007/s11263-025-02431-5.10.1007/s11263-025-02431-5 ↗
10. García-Hidalgo, M., García-Pedrero, Á., Colón, D., Sangüesa-Barreda, G., García-Cervigón, A.I., López-Molina, J., Hernández-Alonso, H., Rozas, V., Olano, J.M., and Alonso-Gómez, V. (2022). CaptuRING: a do-it-yourself tool for wood sample digitization. Methods Ecol. Evol. 13: 1185 1191, https://doi.org/10.1111/2041-210X.13847.10.1111/2041-210X.13847 ↗
11. Hashemi Najafi, S.M., Bousfield, D.W., and Tajvidi, M. (2019). Cracking at the fold in double layer coated paper: the influence of latex and starch composition. Tappi J. 18: 93–99, https://doi.org/10.32964/TJ18.2.93.10.32964/TJ18.2.93 ↗
12. Helanto, K., Talja, R., and Rojas, O.J. (2022). Mineral-filled biopolyester coatings for paperboard packaging materials: barrier, saleability, convertability and biodegradability properties. Nord. Pulp Pap. Res. J. 37: 212–221, https://doi.org/10.1515/npprj-2021-0076.10.1515/npprj-2021-0076 ↗
13. Holik, H. (Ed.) (2013). Handbook of paper and board, 2nd ed., Vol. 1–2. Wiley VCH, Weinheim.10.1002/9783527652495 ↗
14. Horter, T., Ruehl, H., Yang, W., Chiang, Y.-S., Glaeser, K., and Zimmermann, A. (2023). Image analysis based evaluation of print quality for inkjet printed structures. J. Manuf. Mater. Process. 7: 20, https://doi.org/10.3390/jmmp7010020.10.3390/jmmp7010020 ↗
15. Jalilibal, Z., Karavigh, M.H.A., Maleki, M.R., and Amiri, A. (2024). Control charting methods for monitoring high dimensional data streams: a conceptual classification scheme. Comput. Ind. Eng. 191: 110141, https://doi.org/10.1016/j.cie.2024.110141.10.1016/j.cie.2024.110141 ↗
16. Javed, A., Rättö, P., Järnström, L., and Ullsten, H. (2018). Crack analysis of barrier coatings based on starch and starch-PVOH with and without plasticizer. Nord. Pulp Pap. Res. J. 33: 336–347, https://doi.org/10.1515/npprj-2018-3039.10.1515/npprj-2018-3039 ↗
17. Kim, D.-S. and Sung, Y.J. (2023a). Evaluation of changes in fold cracking and mechanical properties of high-grammage paper based on pulp fiber modification. BioResources 18: 3198–3207, https://doi.org/10.15376/biores.18.2.3198-3207.10.15376/biores.18.2.3198-3207 ↗
18. Kim, D.-S. and Sung, Y.J. (2023b). Changes in fold cracking properties and mechanical properties of high-grammage paper as affected by additive and fillers. BioResources 18: 3217–3227, https://doi.org/10.15376/biores.18.2.3217-3227.10.15376/biores.18.2.3217-3227 ↗
19. Kim, C.K., Lim, W.S., and Lee, Y.K. (2010). Studies on the fold-ability of coated paperboard (I): influence of latex on fold-ability during creasing/folding coated paperboard. J. Ind. Eng. Chem. 16: 842–847, https://doi.org/10.1016/j.jiec.2010.05.001.10.1016/j.jiec.2010.05.001 ↗
20. Konovalenko, I., Maruschak, P., and Prentkovskis, O. (2018). Automated method for fractographic analysis of shape and size of dimples on fracture surface of high-strength titanium alloys. Metals-Basel 8: 161, https://doi.org/10.3390/met8030161.10.3390/met8030161 ↗
21. Kumari, S.V.G., Pakshirajan, K., and Pugazhenthi, G. (2022). Recent advances and future prospects of cellulose, starch, chitosan, polylactic acid and polyhydroxyalkanoates for sustainable food packaging applications. Int. J. Biol. Macromol. 221: 163–182, https://doi.org/10.1016/j.ijbiomac.2022.08.203.10.1016/j.ijbiomac.2022.08.203 ↗
22. Kunam, P.K., Ramakanth, D., Akhila, K., and Gaikwad, K.K. (2024). Bio-based materials for barrier coatings on paper packaging. Biomass Conv. Bioref. 14: 12637–12652, https://doi.org/10.1007/s13399-022-03241-2.10.1007/s13399-022-03241-2 ↗
23. Lee, J.-H. and Lee, H.L. (2022). Quantitative analysis of the pigment coating structure influenced by the spreading of latex binder: in situ analysis of correlations between different structural properties. Prog. Org. Coat. 165: 106739, https://doi.org/10.1016/j.porgcoat.2022.106739.10.1016/j.porgcoat.2022.106739 ↗
24. Lee, J.-H., Shin, S.J., Yeu, S.U., and Lee, H.L. (2022). Quantitative characterization of the spreading and adhesion of styrene-butadiene latex binder in the dried pigment coating layer. Prog. Org. Coat. 162: 106555, https://doi.org/10.1016/j.porgcoat.2022.106739.10.1016/j.porgcoat.2021.106555 ↗
25. Lev, R., Tanninen, P., Lyytikäinen, J., and Leminen, V. (2023). Converting and its effects on barrier properties of coated packaging materials: a review. BioResources 18: 8707–8738, https://doi.org/10.15376/biores.18.4.Lev.10.15376/biores.18.4.Lev ↗
26. Lev, R., Lyytikäinen, J., Matthews, S., Koppolu, R., Tanninen, P., and Leminen, V. (2024). Investigating the convertibility and barrier performance of a novel suberin dispersion coating during the paperboard creasing process. Packag. Technol. Sci. 37: 1037–1048, https://doi.org/10.1002/pts.2845.10.1002/pts.2845 ↗
27. Li, Y., Wu, R., Shi, J., and Wang, G. (2021). Sustainable coatings on paper for enhancing barrier properties based on hemicellulose. Nord. Pulp Pap. Res. J. 36: 618–625, https://doi.org/10.1515/npprj-2021-0045.10.1515/npprj-2021-0045 ↗
28. Lyu, K., She, W., Miao, C., Chang, H., and Gu, Y. (2019). Quantitative characterization of pore morphology in hardened cement paste via SEM-BSE image analysis. Constr. Build. Mater. 202: 589–602, https://doi.org/10.1016/j.conbuildmat.2019.01.055.10.1016/j.conbuildmat.2019.01.055 ↗
29. Marinelli, A., Profaizer, M., Diamanti, M.V., Pedeferri, M., and Del Curto, B. (2023). Heat-seal ability and fold cracking resistance of Kaolin-filled styrene-butadiene-based aqueous dispersions for paper-based packaging. Coatings 13: 975, https://doi.org/10.3390/coatings13060975.10.3390/coatings13060975 ↗
30. Mayerhoefer, M.E., Materka, A., Langs, G., Häggström, I., Szczypiński, P., Gibbs, P., and Cook, G. (2020). Introduction to radiomics. J. Nuc. Med. 61: 488–495, https://doi.org/10.2967/jnumed.118.222893.10.2967/jnumed.118.222893 ↗
31. Miao, Y., Jeon, J.Y., and Park, G. (2020). An image processing-based crack detection technique for pressed panel products. J. Manuf. Syst. 57: 287–297, https://doi.org/10.1016/j.jmsy.2020.10.004.10.1016/j.jmsy.2020.10.004 ↗
32. Mirzaei, B., Harksen, T., Smith, S., and Panek, J.C. (2021). Key material properties in crease cracking of kraft paper. Tappi J. 20: 81–89, https://doi.org/10.32964/TJ20.2.81.10.32964/TJ20.2.81 ↗
33. Mirzaei, B., Thompson Johnson, A., Panek, J., and Mwangi, G. (2023). Assessment of paperboard large deformation at fold using digital image correlation technique. Nord. Pulp Pap. Res. J. 38: 261–269, https://doi.org/10.1515/npprj-2022-0088.10.1515/npprj-2022-0088 ↗
34. Mujtaba, M., Lipponen, J., Ojanen, M., Puttonen, S., and Vaittinen, H. (2022). Trends and challenges in the development of bio-based barrier coating materials for paper/cardboard food packaging; a review. Sci. Total Environ. 851: 158328, https://doi.org/10.1016/j.scitotenv.2022.158328.10.1016/j.scitotenv.2022.158328 ↗
35. Oh, K., Sim, K., Jung, Y.B., Youn, H.J., Lee, H.L., Lee, Y.M., and Yeu, S.U. (2015). Effect of coating binder on fold cracking of coated paper. Nord. Pulp Pap. Res. J. 30: 361–368, https://doi.org/10.3183/npprj-2015-30-02-p361-368.10.3183/npprj-2015-30-02-p361-368 ↗
36. Oh, K., Seo, D., Youn, H.J., Lee, Y.M., Yeu, S.U., and Lee, H.L. (2016). Effects of coating composition and folding direction on the fold cracking of coated paper. Nord. Pulp Pap. Res. J. 31: 347–353, https://doi.org/10.3183/npprj-2016-31-02-p347-353.10.3183/npprj-2016-31-02-p347-353 ↗
37. Okhrin, Y., Schmid, W., and Semeniuk, A. (2021). New approaches for monitoring image data. IEEE Trans. Image Process. 30: 921–933, https://doi.org/10.1109/TIP.2020.3039389.10.1109/TIP.2020.3039389 ↗
38. Ong, S.Q., Pinoy, N., Lim, M.H., Bjerge, K., Peris-Felipo, F.J., Lind, R., Cuff, J.P., Cook, S.M., and Høye, T.T. (2025). ScannerVision: scanner-Based image acquisition of medically important arthropods for the development of computer vision and deep learning models. Curr. Res. Parasitol. V. 7: 100268, https://doi.org/10.1016/j.crpvbd.2025.100268.10.1016/j.crpvbd.2025.100268 ↗
39. Pál, M., Novaković, D., Dedijer, S., Koltai, L., Jurič, I., Vladić, G., and Kašiković, N. (2017). Image processing based quality control of coated paper folding. Measurement 100: 99–109, https://doi.org/10.1016/j.measurement.2016.12.033.10.1016/j.measurement.2016.12.033 ↗
40. Pál, M., Dedijer, S., László, K., Gregor-Svetec, D., Cigula, T., Pavlović, Ž., and Milić-Keresteš, N. (2021). Fold cracking of coated papers: investigation on automated computer-aided visual assessment method. Nord. Pulp Pap. Res. J. 36: 626–642, https://doi.org/10.1515/npprj-2021-0041.10.1515/npprj-2021-0041 ↗
41. Panek, J. and Hart, P. (2022). Review of coating cracking and barrier integrity on paperboard substrates. Tappi J. 21: 589–603, https://doi.org/10.32964/tj21.11.589.10.32964/TJ21.11.589 ↗
42. Panek, J., Smith, S., and Coffin, D. (2020). Creasing severity and reverse-side cracking. Tappi J. 19: 219–227, https://doi.org/10.32964/TJ19.4.219.10.32964/TJ19.4.219 ↗
43. Rajabi Abhari, A., Lee, H.L., Oh, K., Im, W., Lee, J.-H., Lee, S., and Kim, S. (2018). Suspension-polymerized latex as an additive for surface sizing and its effect on fold cracking of coated paper. BioResources 13: 7640–7653, https://doi.org/10.15376/biores.13.4.7640-7653.10.15376/biores.13.4.7640-7653 ↗
44. Rättö, P. and Hornatowska, J. (2010a). The influence of coating colour composition on the crack area after creasing. Nord. Pulp Pap. Res. J. 25: 495–501, https://doi.org/10.3183/npprj-2010-25-04-p495-501.10.3183/npprj-2010-25-04-p495-501 ↗
45. Rättö, P. and Hornatowska, J. (2010b). Dynamic aspects of crack development in coating layers. In: Proceedings of TAPPI 11th advanced coating fundamentals symposium, Munich, Germany.
46. Rättö, P., Hornatowska, J., and Barbier, C. (2012). Influence of the distribution of the shape and size distribution of pigment particles on cracking in coating layers during creasing. Nord. Pulp Pap. Res. J. 27: 714–720, https://doi.org/10.3183/npprj-2012-27-04-p714-720.10.3183/npprj-2012-27-04-p714-720 ↗
47. Ruberto, Y., Vivod, V., Grkman, J.J., Gregor Lavrič, G., Graif, C., and Kokol, V. (2024). Slot-die coating of cellulose nanocrystals and chitosan for improved barrier properties of paper. Cellulose 31: 3589–3606, https://doi.org/10.1007/s10570-024-05847-3.10.1007/s10570-024-05847-3 ↗
48. Scapicchio, C., Gabelloni, M., Barucci, A., Cioni, D., Saba, L., and Neri, E. (2021). A deep look into radiomics. Radiol. Med 126: 1296–1311, https://doi.org/10.1007/s11547-021-01389-x.10.1007/s11547-021-01389-x ↗
49. Sim, K., Youn, H.J., Oh, K.D., Lee, H.L., Han, C.S., Yeu, S.U., and Lee, Y.M. (2012). Fold cracking of coated paper: the effect of pulp fiber composition and beating. Nord. Pulp Pap. Res. J. 27: 445–450, https://doi.org/10.3183/npprj-2012-27-02-p445-450.10.3183/npprj-2012-27-02-p445-450 ↗
50. Varney, D. and Bousfeld, D. (2019). Discrete element method to model cracking for two-layer systems. Tappi J. 18: 101–108, https://doi.org/10.32964/TJ18.2.101.10.32964/TJ18.2.101 ↗
51. Versino, F., Ortega, F., Monroy, Y., Rivero, S., López, O.V., and García, M.A. (2023). Sustainable and bio-based food packaging: a review on past and current design innovations. Foods 12: 1057, https://doi.org/10.3390/foods12051057.10.3390/foods12051057 ↗
52. Vinitskaia, N., Lindstad, A., Lev, R., Kvikant, M., Xu, C., Leminen, V., Li, K., Pettersen, M., and Grönman, K. (2025). Environmental sustainability, food quality and convertibility of bio-based barrier coatings for fibre-based food packaging: a semisystematic review. Packag. Technol. Sci. 38: 255–280, https://doi.org/10.1002/pts.2868.10.1002/pts.2868 ↗
53. Wang, Q. and Ding, N. (2020). Coating factors influencing the fold cracking of coated papers. Nord. Pulp Pap. Res. J. 35: 419–431, https://doi.org/10.1515/npprj-2019-0051.10.1515/npprj-2019-0051 ↗
54. Wang, P., Lee, Y.H., Tseng, H.W., and Yang, C.F. (2023). Research and evaluation on an optical automatic detection system for the defects of the manufactured paper cups. Sensors 23: 1452, https://doi.org/10.3390/s23031452.10.3390/s23031452 ↗
55. Xia, Y., Wang, S., Meng, F., Xu, Z., Fang, Q., Gu, Z., Zhang, C., Li, P., and Kong, F. (2024). Eco-friendly food packaging based on paper coated with a bio-based antibacterial coating composed of carbamate starch, calcium lignosulfonate, cellulose nanofibrils, and silver nanoparticles. Int. J: Biol. Macromol. 254: 127659, https://doi.org/10.1016/j.ijbiomac.2023.127659.10.1016/j.ijbiomac.2023.127659 ↗
56. Yang, A., Xie, Y., and Renjung, W. (2011). From theory to practice: improving the foldcrack resistance of industrially produced triple coated paper. In: Proceedings of Tappi PaperCon conference, May 1–4, 2011, Covington, KY, USA, pp. 1845–1858. https://www.tappi.org/content/events/11papercon/documents/184.401.pdf (Accessed 20 April 2025).
57. Yang, D., Liu, Q., Gao, Y., Wan, S., Meng, F., Weng, W., and Zhang, Y. (2023). Characterization of silver nanoparticles loaded chitosan/polyvinyl alcohol antibacterial films for food packaging. Food Hydrocolloids 136: 108305, https://doi.org/10.1016/j.foodhyd.2022.108305.10.1016/j.foodhyd.2022.108305 ↗
58. Yeganeh, A., Johannssen, A., and Chukhrova, N. (2024). The partitioning ensemble control chart for on-line monitoring of high-dimensional image-based quality characteristics. Eng. Appl. Artif. Intell. 127: PB, https://doi.org/10.1016/j.engappai.2023.107282.10.1016/j.engappai.2023.107282 ↗
59. Zhang, F., Zhao, H., Sha, L., Li, J., Guo, D., and Yuan, T. (2023). One-step fabrication of eco-friendly multi-functional amphiphobic coatings for cellulose-based food packaging. Int. J. Biol. Macromol. 253: 127578, https://doi.org/10.1016/j.ijbiomac.2023.127578.10.1016/j.ijbiomac.2023.127578 ↗
60. Zhu, Z., Bousfield, D., and Gramlich, W. (2019). The influence of pigment type and loading on water vapor barrier properties of paper coatings before and after folding. Prog. Org. Coat. 132: 201–210, https://doi.org/10.1016/j.porgcoat.2019.03.031.10.1016/j.porgcoat.2019.03.031 ↗
61. Zhu, Z., Bousfield, D., and Gramlich, W. (2021). Failure prediction of waterborne barrier coatings during folding. J. Coat. Technol. Res. 18: 1117–1129, https://doi.org/10.1007/s11998-021-00465-1.10.1007/s11998-021-00465-1 ↗
62. Zhu, Y., Bousfield, D., and Gramlich, W. (2022). The influence of pigment modulus on failure resistance of paper barrier coatings. Nord. Pulp Pap. Res. J. 37: 97–107, https://doi.org/10.1515/npprj-2021-0052.10.1515/npprj-2021-0052 ↗