Correlation of fracture toughness with microstructural features for ultrafine‐grained 6082 Al alloy
Source abstract
Abstract
Abstract In the present work, cryorolling (CR) and room temperature rolling (RTR) followed by annealing (AN) at 200°C were carried out to investigate the effects of grain size, precipitates (Mg‐Si‐phases), and AlFeMnSi‐phases on the fracture toughness of 6082 Al alloy. Using the values of the conditional fracture toughness, (KQ), in the critical fracture toughness (KIC) validation criteria, it was found that the sample size is inappropriate, which implies that the conditional fracture toughness obtained cannot be considered as the critical fracture toughness. Therefore, to establish the relative improvement in fracture toughness, the equivalent energy fracture toughness (Kee) and J‐integral were calculated and used. The results show that the values of Kee (89.91 MPa √m) and J (89.86 kJ/m2) obtained for the sample processed via CR followed by AN (CR + AN) are the highest when compared with the other samples processed through CR, RTR, and RTR followed by AN, RTR + AN. Microstructural features such as high fraction of low Taylor factor, high fraction of kernel average misorientation, Si‐rich particles, small size AlFeMnSi‐phases, and mixed mode of failure (transgranular shear and micro‐void coalescence) also support the high fracture toughness in the CR + AN sample. It was also observed that the effect of residual stresses on the fracture toughness of CR and RTR samples is minimal. Therefore, the correlation between microstructure and residual stresses is not considered in the present work due to very small values of the residual stresses for CR and RTR samples and the absence of residual stress from the heat‐treated samples.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Microstructure and mechanical properties · Microstructure and Mechanical Properties of Steels · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical Engineering Howard University Washington D.C. 20059 USA
Department of Engineering Design Indian Institute of Technology Madras Chennai 600036 India
Herbert Gleiter Institute of Nanoscience Nanjing University of Science and Technology Nanjing Jiangsu China
Funding
Department of Defense, USA
References (44)
Show source-provided references
1. 10.1016/j.actamat.2006.06.00510.1016/j.actamat.2006.06.005 ↗
2. 10.1016/j.jallcom.2014.12.15910.1016/j.jallcom.2014.12.159 ↗
3. 10.1016/j.matdes.2012.11.04710.1016/j.matdes.2012.11.047 ↗
4. 10.1016/j.matchemphys.2015.09.01410.1016/j.matchemphys.2015.09.014 ↗
5. 10.1016/j.matchar.2015.07.03310.1016/j.matchar.2015.07.033 ↗
6. 10.1016/j.matdes.2016.03.09510.1016/j.matdes.2016.03.095 ↗
7. 10.1016/j.matdes.2015.09.02910.1016/j.matdes.2015.09.029 ↗
8. 10.1016/j.msea.2015.06.01910.1016/j.msea.2015.06.019 ↗
9. 10.1007/s11665-016-2126-010.1007/s11665-016-2126-0 ↗
10. 10.1016/j.msea.2017.03.03410.1016/j.msea.2017.03.034 ↗
11. 10.1016/j.jnucmat.2007.03.07910.1016/j.jnucmat.2007.03.079 ↗
12. 10.1016/j.engfailanal.2016.03.01010.1016/j.engfailanal.2016.03.010 ↗
13. 10.1016/j.msea.2009.12.03310.1016/j.msea.2009.12.033 ↗
14. 10.1016/j.actamat.2015.07.04910.1016/j.actamat.2015.07.049 ↗
15. 10.1016/j.scriptamat.2011.02.00710.1016/j.scriptamat.2011.02.007 ↗
16. 10.1007/s11661-009-0111-z10.1007/s11661-009-0111-z ↗
17. The effect of incoherent particles on toughness of an Al‐Mg‐Si alloy
18. 10.1016/S1003-6326(17)60055-410.1016/S1003-6326(17)60055-4 ↗
19. 10.1016/j.msea.2013.03.02110.1016/j.msea.2013.03.021 ↗
20. 10.1007/s11665-014-1096-310.1007/s11665-014-1096-3 ↗
21. Dieter GE · 1
22. 10.1016/j.engfracmech.2012.02.00110.1016/j.engfracmech.2012.02.001 ↗
23. 10.1115/1.360120610.1115/1.3601206 ↗
24. DonatoGHB RuggieriC.Estimation procedures for J and CTOD fracture parameters using three‐point bend specimens. Proc IPC.2006;2006:19‐26.10.1115/IPC2006-10165 ↗
25. 10.1088/0034-4885/67/8/R0210.1088/0034-4885/67/8/R02 ↗
26. Taylor GI · 1938 · 218
27. Plastic strain in metals
28. Physics and phenomenology of strain hardening: the FCC caseProg
29. Texture evolution and ultrafine grained formation in cross‐cryo‐rolled Zircaloy‐210.1007/s40195-015-0267-z ↗
30. 10.1007/s13632-015-0219-z10.1007/s13632-015-0219-z ↗
31. 10.2320/matertrans.45.231610.2320/matertrans.45.2316 ↗
32. 10.1016/j.ijfatigue.2011.02.00610.1016/j.ijfatigue.2011.02.006 ↗
33. 10.1016/j.ijfatigue.2016.03.01810.1016/j.ijfatigue.2016.03.018 ↗
34. 10.1016/j.msea.2013.11.07910.1016/j.msea.2013.11.079 ↗
35. 10.1016/j.actamat.2007.01.03810.1016/j.actamat.2007.01.038 ↗
36. 10.1016/S1359-6462(03)00396-810.1016/S1359-6462(03)00396-8 ↗
37. 10.1016/j.msea.2007.01.06210.1016/j.msea.2007.01.062 ↗
38. 10.1016/j.msea.2006.04.04410.1016/j.msea.2006.04.044 ↗
39. 10.1016/j.actamat.2011.01.01710.1016/j.actamat.2011.01.017 ↗
40. Cryogenic toughness of commercial aluminum‐lithium alloys: role of delamination toughening10.1007/BF02653929 ↗
41. 10.1016/S0036-9748(88)80312-010.1016/S0036-9748(88)80312-0 ↗
42. 10.1520/STP34909S10.1520/STP34909S ↗
43. 10.1520/STP26927S10.1520/STP26927S ↗
44. 10.1016/j.matchar.2017.02.00310.1016/j.matchar.2017.02.003 ↗