journal article·2026-06-01

Numerical and experimental analysis of thermal design of a drying chamber for roll-to-roll (R2R) printing devices

Hyeokgyun Moon, Ritesh Prakash, Moe Moe Than, Bukuk Oh, Gyoujin Cho, Jinkee Lee

Flexible and Printed Electronics· Volume 11· Issue 2
Publisher page

Abstract

Abstract This study evaluates the thermal performance of a hot-air drying chamber for roll-to-roll (R2R) flexible electronics using experiments and three-dimensional heat transfer simulations. A computational fluid dynamic model incorporating a moving reference frame for the polyethylene terephthalate film was developed in ANSYS Fluent (ANSYS Inc., USA) and validated against measured surface temperature data over film speeds ranging from 10 to 90 mm s −1 , yielding errors below 10.4%. At 90 mm s −1 , the baseline chamber with 6 mm distributor holes showed a time-averaged spatial coefficient of variation ( {\overset{―}{CV}}s ) of 3.87% and a temporal coefficient of variation ( C{V}t ) of 1.84% in the transverse direction. Increasing the distributor hole diameter from 6 to 8 or 9 mm resulted in little to no improvement in transverse temperature uniformity, due to the reduced jet momentum and enhanced thermal stratification. In contrast, a multi-diameter configuration (6 mm bottom half, 7 mm middle quarter, and 8 mm top quarter) effectively compensated for hydrostatic pressure drop, ensuring balanced airflow, enhanced mixing, and fewer recirculation zones. This optimized design reduced {\overset{―}{CV}}s to 2.18% and C{V}t to 1.71%, representing improvements of 43.67% and 7.07% relative to the baseline case. As a result, the chamber delivered more uniform and stable thermal conditions, particularly in the downstream region which critically governs the drying process. The proposed multi-diameter distributor design offers a simple and cost-effective retrofit that significantly enhances thermal uniformity, which is expected to reduce drying-related defects such as cracking, delamination, and poor adhesion in printed electronics. These results offer practical guidelines for optimizing thermal design in high-performance R2R drying systems.
Source: crossref · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Nanomaterials and Printing Technologies · Rheology and Fluid Dynamics Studies · Heat Transfer and Numerical Methods

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Sungkyunkwan University

Indian Institute of Technology (Indian School of Mines

Materials and Production Engineering Research Institute, LG Electronics

Funding

National Research Foundation of Korea

References (32)

Show source-provided references
1. A review on printed electronics: fabrication methods, inks, substrates, applications and environmental impacts10.3390/jmmp5030089 ↗
2. Fully roll-to-roll gravure printed electronics: challenges and the way to integrating logic gates10.35848/1347-4065/ac48d3 ↗
3. The 2021 flexible and printed electronics roadmap10.1088/2058-8585/abf986 ↗
4. Roll-to-roll printing of perovskite solar cells10.1021/acsenergylett.8b01556 ↗
5. Roll-to-roll gravure printed electrochemical sensors for wearable and medical devices10.1021/acsnano.8b02505 ↗
6. Towards roll-to-roll printed batteries based on organic electrodes for printed electronics applications10.1016/j.est.2021.102680 ↗
7. A facile process combined with roll-to-roll flexographic printing and electroless deposition to fabricate RFID tag antenna on paper substrates10.1016/j.compositesb.2021.109194 ↗
8. Roll-to-roll, dual-layer slot die coating of chitin and cellulose oxygen barrier films for renewable packaging10.1021/acsami.2c09925 ↗
9. Effect of process parameters on the morphology and nanostructure of roll-to-roll printed P3HT: PCBM thin films for organic photovoltaics10.1016/j.solmat.2012.12.044 ↗
10. Web unevenness due to thermal deformation in the roll-to-roll manufacturing process10.3390/app10238636 ↗
11. Strain optimization of tensioned web through computational fluid dynamics in the roll-to-roll drying process10.3390/polym14122515 ↗
12. Web wrinkle defects due to temperature profile in roll-to-roll manufacturing systems10.3390/polym15020457 ↗
13. A study of hybrid drying process to improve drying speed and electrical conductivity for roll-to-roll printing10.1143/JJAP.49.05EC10 ↗
14. Upscaling of polymer solar cell fabrication using full roll-to-roll processing10.1039/b9nr00430k ↗
15. Ink‐jet printing and microwave sintering of conductive silver tracks10.1002/adma.200502422 ↗
16. Rapid uniformity analysis of fully printed SWCNT-based thin film transistor arrays via roll-to-roll gravure process10.3390/nano13030590 ↗
17. A review: fundamentals of computational fluid dynamics (CFD)10.1063/1.5066893 ↗
18. Roll to roll air-floating oven drying process design and analysis for printed electronics10.1007/s12541-014-0470-2 ↗
19. Ahmed · 2020
20. A comparative analysis of printed circuit drying methods for the reliability of assembly process10.1016/j.microrel.2022.114478 ↗
21. Delamination behavior of lithium-ion battery anodes: influence of drying temperature during electrode processing10.1080/07373937.2015.1060497 ↗
22. Control of the coffee ring effect during R2R gravure printing for minimizing threshold voltage variation in printed carbon nanotube-based thin film transistors10.1016/j.mtadv.2023.100385 ↗
23. ANSYS, · 2025
24. Statistical properties of turbulent free jets issuing from nine differently-shaped nozzles10.1007/s10494-009-9240-0 ↗
25. Digital twins: a solution under the standard k-ϵ model in industrial CFD, to predict ideal conditions in a sugar dryer10.3390/fluids10060146 ↗
26. Versteeg · 2007
27. Patankar · 2018
28. Incropera · 2017
29. Microstructural and thermomechanical simulation of the additive manufacturing process in 316L austenitic stainless steel10.3390/IEC2M-09237 ↗
30. Bathe · 2006
31. Mean absolute percentage error for regression models10.1016/j.neucom.2015.12.114 ↗
32. Evaluation of various turbulence models in predicting airflow and turbulence in enclosed environments by CFD: part 2—Comparison with experimental data from literature10.1080/10789669.2007.10391460 ↗