Electrohydrodynamic printed nanoparticle-based resistive temperature sensor
Source abstract
Abstract
Abstract Temperature sensors based on the principle of a change of resistance are fabricated on polyethylene terephthalate (PET) substrates using a silver nanoparticles (AgNPs)-based ink using a bespoke drop-on-demand (DoD) electrohydrodynamic (EHD) printer. Two sensors consisting of either a single or double layer of silver were deposited using EHD printing and were found to exhibit an internal resistance of a few hundred ohms for the double-layer sensor compared to 1 kΩ for the single-layer sensor. The achieved pattern width was almost half the size of nozzle internal diameter (160 μ m), and printed without treatment of substrate and nozzle. The sensors were characterized over a temperature range of 20 °C–110 °C. Both sensors showed a linear behavior with low hysteresis within the temperature ranges considered in this study and are found to recover the nominal resistance value with good reproducibility. The double-layer sensor showed high sensitivity with a temperature coefficient of resistance (TCR) of 3.4 × 10 −3 {}∘{C}−1 , which is an order of magnitude larger than that observed for the single-layered sensor with a TCR of 8.41 × 10 −4 {}∘{C}−1 . The sensors were also tested in a controlled humid environment and results are presented on the dependence of the internal resistance on the level of humidity. The proposed flexible printed sensors are promising for temperature monitoring systems and wearable technologies.
Source: crossref · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electrohydrodynamics and Fluid Dynamics · Advanced Sensor and Energy Harvesting Materials · Nanomaterials and Printing Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. Printed Wheatstone bridge with embedded polymer based piezoresistive sensors for strain sensing applications10.1016/j.addma.2018.01.004 ↗
2. All-printed flexible and stretchable electronics10.1002/adma.201604965 ↗
3. Inkjet printed electronics using copper nanoparticle ink10.1007/s10854-009-0049-3 ↗
4. Printed electronics: present and future opportunities10.1109/ICSensT.2015.7438427 ↗
5. High-resolution electrohydrodynamic jet printing10.1038/nmat1974 ↗
6. Direct fabrication of copper nanoparticle patterns through electrohydrodynamic printing in cone-jet mode10.1080/10426914.2012.663121 ↗
7. Ink bridge control in the electrohydrodynamic printing with a coaxial nozzle10.1016/j.jmapro.2020.10.057 ↗
8. Tip-assisted electrohydrodynamic jet printing for high-resolution microdroplet deposition10.1016/j.matdes.2019.107609 ↗
9. Direct printing of copper conductive micro-tracks by multi-nozzle electrohydrodynamic inkjet printing process10.1016/j.jmatprotec.2011.10.024 ↗
10. Fine-resolution patterning of copper nanoparticles through electrohydrodynamic jet printing10.1088/0960-1317/22/6/065012 ↗
11. High-speed and drop-on-demand printing with a pulsed electrohydrodynamic jet10.1088/0960-1317/20/9/095026 ↗
12. Fine resolution drop-on-demand electrohydrodynamic patterning of conductive silver tracks on glass substrate10.1007/s00339-012-7267-x ↗
13. Study of drop-on-demand printing through multi-step pulse voltage10.1007/s12541-011-0086-8 ↗
14. High-resolution ac-pulse modulated electrohydrodynamic jet printing on highly insulating substrates10.1088/0960-1317/24/4/045010 ↗
15. Electrically tunable printed bifocal liquid crystal microlens arrays10.1002/admi.202000578 ↗
16. A carbon nanotube strain sensor for structural health monitoring10.1088/0964-1726/15/3/009 ↗
17. In-situprocess and condition monitoring of advanced fibre-reinforced composite materials using optical fibre sensors10.1088/0964-1726/7/2/002 ↗
18. Paper-based printed impedance sensors for water sorption and humidity analysis10.1088/2058-8585/aa5eeb ↗
19. Inkjet printed nanomaterial based flexible radio frequency identification (RFID) tag sensors for the internet of nano things10.1039/C7RA07191D ↗
20. Temperature sensor realized by inkjet printing process on flexible substrate10.1016/j.mseb.2015.11.003 ↗
21. Large-area compatible fabrication and encapsulation of inkjet-printed humidity sensors on flexible foils with integrated thermal compensation10.1088/0960-1317/23/2/025012 ↗
22. Inkjet printing on paper for the realization of humidity and temperature sensors10.1109/TRANSDUCERS.2011.5969506 ↗
23. Characterization of flexible temperature sensor fabricated through drop-on-demand electrohydrodynamics patterning10.7567/JJAP.53.05HB02 ↗
24. Mechanisms, capabilities, and applications of high-resolution electrohydrodynamic jet printing10.1002/smll.201500593 ↗
25. A research on sintering process of conductive silver paste in low temperature used for silk-screen printing10.1063/1.5048744 ↗
26. Simulation and prediction of the thermal sintering behavior for a silver nanoparticle ink based on experimental input10.1039/C4TC00632A ↗
27. The characterization of electrically conductive silver ink patterns on flexible substrates10.1016/j.microrel.2009.04.004 ↗
28. Facile synthesis of PdAgCo trimetallic nanoparticles for formic acid electrochemical oxidation10.1246/cl.160243 ↗
29. The impact of surface properties of polymeric substrates on the nano-behavior10.1109/ISSE.2016.7563225 ↗
30. Tailoring the temperature coefficient of resistance of silver nanowire nanocomposites and their application as stretchable temperature sensors10.1021/acsami.9b04045 ↗