Effect of Growth Rings Per Inch and Specific Gravity on Compression Perpendicular to Grain in No. 2: 2 by 8 and 2 by 10 Southern Pine Lumber
Source abstract
Abstract
Abstract Southern pine lumber 2 by 8s and 2 by 10s from across the Southeast were used as the parent material source for this study. Fundamental data were collected for each piece of lumber: growth rings per inch (RPI), presence of pith, and specific gravity (SG), among other information. After mechanical property evaluation through static bending, small clear specimens were cut from the lumber pieces and tested for compression perpendicular to grain (C⊥). Those values were then compared with 2 by 8 and 2 by 10 average RPI and density. The results were significant for both tests. Therefore, a segmentation of the growth ring data into groups of <3, 3 to 5, and >5 RPI was conducted. Correlations were run specific to each group, per both lumber sizes, and still significance was found. Segmentation of SG was not significant only for 2 by 8 SG <0.4. The results suggest that SG is a better predictor of C⊥ than RPI alone due to statistical significance found during these analyses.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Wood Treatment and Properties · Tree Root and Stability Studies · Material Properties and Processing
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (42)
Show source-provided references
1. Allen, H. L. and T. Fox. 2005. What is ahead for intensive pine plantation silviculture in the South? South. J. Appl. Forestry29(2):62–69.
2. American Forest and Paper Association (AFPA). 2005. National design specification (NDS) for wood construction with commentary and supplement: Design values for wood construction 2005 edition. AFPA, Washington, D.C.
3. American Lumber Standards Committee (ALSC). 2013. American lumber standards committee board of review: Board of review minutes. 1 February 2013. ALSC, Germantown, Maryland.
4. ASTM International. 2014. Standard test methods for small clear specimens of timber. ASTM D143. ASTM International, West Conshohocken, Pennsylvania.
5. ASTM International. 2015. Standard test methods of statics of lumber in structural sizes. ASTM D198. ASTM International, West Conshohocken, Pennsylvania.
6. ASTM International. 2017. Standard test methods for density and specific gravity (relative density) of wood and wood-based materials. ASTM D2395. ASTM International, West Conshohocken, Pennsylvania.
7. ASTM International. 2019. Standard practice for establishing allowable properties for visually-graded dimension lumber from in-grade tests of full-size specimens. ASTM D1990. ASTM International, West Conshohocken, Pennsylvania.
8. Biblis, E. J. 2006. Flexural properties and compliance to visual grade requirements of 2 by 4 and 2 by 6 loblolly pine lumber obtained from 19 year old plantations. Forest Prod. J. 56(9):71–73.
9. Brashaw, B. K., V. Bucur, F. Divos, R. Goncalves, J. X. Lu, R. Meder, R. F. Pellerin, S. Potter, R. J. Ross, X. Wang, and Y. F. Yin. 2009. Nondestructive testing and evaluation of wood: A worldwide research update. Forest Prod. J. 59(3):7–14.
10. Butler, M. S., J. Dahlen, F. Antony, M. Kane, T. L. Eberhardt, H. Jin, K. Love-Myers, and J. P. McTague. 2016. Relationships between loblolly pine small clear specimens and dimension lumber tested in static bending. Wood Fiber Sci. 48(2):81–95.
11. Dahlen, J., D. Auty, and T. L. Eberhardt. 2018. Models for predicting density and ring width for loblolly pine from intensively managed plantations, and implications for wood utilization. Forests9(292):1–20.
12. Dahlen, J., P. D. Jones, R. D. Seale, and R. Shmulsky. 2012. Bending strength and stiffness of in-grade Douglas-fir and southern pine No. 2 2 × 4 lumber. Can. J. Forest Res. 42(5):858–867.
13. Dahlen, J., P. D. Jones, R. D. Seale, and R. Shmulsky. 2014. Bending strength and stiffness of wide dimension southern pine No. 2 lumber. Eur. J. Wood Wood Prod. 72(6):759–768.
14. Doyle, D. V. and L. J. Markwardt. 1966. Properties of southern pine in relation to strength grading of dimension lumber. Research Paper FPL-RP-64. USDA Forest Service, Forest Products Laboratory, Madison, Wisconsin. 62pp.
15. Fox, T. R., E. J. Jokela, and H. L. Allen. 2004. The evolution of pine plantation silviculture in the southern United States. In:Southern Forest Science: Past, Present, and Future. H. M. Rauscher and K. Johnsen (Eds.). Forest Service General Technical Report SRS-75. US Department of Agriculture, Washington, D.C.pp. 63–82.
16. França, F. J. N., T. S. F. A. França, R. D. Seale, and R. Shmulsky. 2020. Nondestructive evaluation of 2 by 8 and 2 by 10 southern pine dimensional lumber. Forest Prod. J. 70(1):79–87.
17. França, F. J. N., R. D. Seale, R. Shmulsky, and T. S. F. A. França. 2018 b. Assessing southern pine 2 × 4 and 2 × 6 lumber quality: Longitudinal and transverse vibration. Wood Fiber Sci. 51(1):2–15.
18. França, F. J. N., R. D. Seale, R. Shmulsky, and T. S. F. A. França. 2018 c. Modeling mechanical properties of 2 by 4 and 2 by 6 southern pine lumber using longitudinal vibration and visual characteristics. Forest Prod. J. 68(3):286–294.
19. França, T. S. F. A., F. J. N. França, R. D. Seale, and R. Shmulsky. 2018 a. Bending strength and stiffness of No. 2 grade southern pine lumber. Wood Fiber Sci. 50(2):1–15.
20. Frese, M. 2008. Visual strength grading supported by mechanical grading. In:ConfCOST E53, October 29–30, 2008, Delft, the Netherlands; Delft University of Technology, the Netherlands. pp. 19–30.
21. Green, D. W. 2001. Wood: Strength and stiffness. In:Encyclopedia of Materials: Science and Technology. K. H. J. Buschow (Ed.). Elsevier, Amsterdam and New York. pp. 9732–9736
22. IBM. 2018. IBM SPSS statistics for windows, version 25.0. IBM Corporation, Armonk, New York.
23. Irby, N. E., F. J. N. França, H. M. Barnes, R. Seale, and R. Shmulsky. 2020. Effect of growth rings per inch and density on compression parallel to grain in southern pine lumber. BioResources15(1).
24. James, E., D. E. Kretschmann, C. C. Hatfield, and D. W. Green. 2013. Analysis of the Part I Southern Pine In-Grade Program data. Report GTR-221. USDA Forest Products Laboratory, Madison, Wisconsin. 15pp.
25. Kenesh, R. H. 1968. Strength and elastic properties of wood in perpendicular compression. Forest Prod. J. 18(1):65–72.
26. Kretschmann, D. E. 1997. Effect of juvenile wood on shear parallel and compression perpendicular-to-grain strength of loblolly pine. Research Paper FPL-RP-647. USDA Forest Service, Forest Products Laboratory, Madison, Wisconsin. 25pp.
27. Kretschmann, D. E. 2010. Stress grades and design properties for lumber, round timber, and ties. In:Wood Handbook. W. RamsaySmith (Ed.). General Technical Report FPL-GTR-190. USDA Forest Service, Forest Products Laboratory, Madison, Wisconsin. pp. 7-1–7-16.
28. Kretschmann, D. E. and B. A. Bendtsen. 1992. Ultimate tensile stress and modulus of elasticity of fast-grown plantation loblolly pine lumber. Wood Fiber Sci. 24(2):189–203.
29. Kretschmann, D. E., J. W. Evans, and L. Brown. 1999. Monitoring of visually graded structural lumber. Research Paper FPL-RP-576. USDA Forest Service, Forest Products Laboratory, Madison, Wisconsin. 18pp.
30. Madsen, B. and L. F. Nielsen. 1976. In-grade testing: Size investigations on lumber subjected to bending. Structural Research Series Report 15. Department of Civil Engineering, University of British Columbia, Vancouver.
31. Markwardt, L. J. and T. R. C. Wilson. 1935. Strength and related properties of woods grown in the United States. Technical Bulletin 479. USDA Forest Service, Forest Products Laboratory, Washington, D.C. 99pp.
32. Mascia, N. T. and S. M. Cramer. 2009. On the effect of the number of annual growth rings, specific gravity and temperature on redwood elastic modulus. Maderas Cienc. Tecnol. 11(1):47–60.
33. Newlin, J. A. and T. R. C. Wilson. 1917. Mechanical properties of woods grown in the United States. Technical Bulletin 556. USDA Forest Service, Forest Products Laboratory, Washington, D.C. pp. 551–575.
34. Panshin, A. J. and D. deZeeuw. 1980. Textbook of Wood Technology. Vol. 1, 4th ed. McGraw-Hill, New York.
35. Shmulsky, R. and P. D. Jones. 2019. Forest Products and Wood Science: An Introduction. 7th ed. John Wiley & Sons, Hoboken, New Jersey. 482pp.
36. Southern Pine Forest Production Association (SFPA). 2005. Industry statistics: Annual production from 2000 to 2005. White Paper. SFPA, Kenner, Louisiana.
37. Southern Pine Inspection Bureau (SPIB). 2014. Standard grading rules for southern pine lumber. SPIB, Pensacola, Florida. 152pp.
38. Stoker, D. L., R. G. Pearson, D. E. Kretschmann, Y. Tang, and B. Simpson. 2007. Effect of press-drying on static bending properties of plantation-grown No. 2 loblolly pine lumber. Forest Prod. J. 57(11):70–73.
39. Wang, X. 2013. Stress wave E-rating of structural timber—Size and moisture content effects. General Technical Report FPL-GTR-226. In:Proceedings of the 18th International Nondestructive Testing and Evaluation of Wood Symposium, R. J. Ross and X. Wang, (Eds.), September 24–27, 2013, Madison, Wisconsin;USDA Forest Service, Forest Products Laboratory, Madison, Wisconsin. pp. 38–46.
40. Yang, B. Z., R. D. Seale, R. Shmulsky, J. Dahlen, and X. Wang. 2015 a. Comparison of nondestructive testing methods for evaluating No. 2 southern pine lumber. Part A, modulus of elasticity. Wood Fiber Sci. 47(4):1–10.
41. Yang, B. Z., R. D. Seale, R. Shmulsky, J. Dahlen, and X. Wang. 2015 b. Comparison of nondestructive testing methods for evaluating No. 2 southern pine lumber. Part B, modulus of rupture. Wood Fiber Sci. 47(4):1–10.
42. Zhang, Y., I. Majumdar, and J. Schelhas. 2010. Changes in woodland use from longleaf pine to loblolly pine. Sustainability2:2734–2745.